The developer will be on vacation from August 6 to August 18 inclusive. No activations will be performed during this period. Support will work in weekend mode.

 

A new version of the program 1.4.8 has been released:

 

1. The virtual reading function has been added to the module 13 "Honda/Acura ECU with K-line".

2. In module 51 of the "China Vehicle ECU", test support has been added for the ME17.8.8 ECU installed on Hisun ATVs (direct connection only), as well as the MT95.1 ECU installed on BAIC hybrid vehicles. It supports reading, writing, checking, and correcting checksums. Improved stability of operation with MT95.1 ECUs installed on Tank vehicles.

 

BAIC 2.0T PHEV (Delphi MT95.1) [THU/PO/CS]

 

3. In module 53 "Infineon Tricore Bootloader", the ability to read the password of the SID807EVO ECU used in Volvo vehicles has been added.

4. In the 57" module of the SIMOS 8/10/11/12/PCR2 ECU.1" improved operation in service mode with the Simos 12.

5 ECU. In module 59 "Renault/Nissan ECU with UDS protocol", test support for the BED511 ECU has been added. Supports reading, writing, checking, and correcting checksums.

6. Module 74 of the Toyota/Lexus Generation 3 ECU has added support for the ECU used with 1GD-FTV diesel engines in vehicles of the LC7x family. Supports reading, writing, checking, and correcting checksums.

 

LC7x 2.8TD P5-UDS (1GD-FTV/2GD-FTV/R7F701216) [THU/PO/CS]

LC7x 2.8TD MCU #2 P5-UDS (1GD-FTV/R7F701201) [THU/PO/CS]

 

7. Module 77 "Service mode of Bosch ME9/MED9/EDC7/EDC16/PSG16/TCU ECU" has added support for MED9 ECU.6.1, used in Ferrari vehicles. It supports reading, writing, checking, and correcting checksums.

8. In module 82 "Service mode of the Bosch SH725XX transmission control unit", the ability to reboot the VGS-NAG3 control unit has been added, which is necessary for "cloning" the control unit.

9. Module 87 "ECU Citroen/Peugeot Delphi DCM6.2/DCM7.1B" now provides full support for ECU DCM7.1B used in Citroen, Peugeot, Opel, Fiat vehicles.

 

Citroen/Peugeot 2.0L HDi (DCM7.1B) [THU/PO/CS]

Citroen/Peugeot 2.0L HDi EEPROM (DCM7.1B) [THU/PO]

 

10. In module 89 of the "MG1/Denso ECU of China", test support for the MG1US008 ECU used in BYD and Roewe vehicles has been added. It supports reading, writing, checking, and correcting checksums.

11. Module 92 "Bosch MD1/MG1 ECU Service Mode" adds support for the TC389QP microcontroller used in the PDCU8.0 ECU, and also adds support for ECU operation with TC2xx family microcontrollers unlocked for service mode by third-party boot loaders.

12. Module 95 "Toyota/Lexus Generation 4 ECU" adds support for ECU used with 1GD-FTV diesel engines in Hiace vehicles. Reading and writing are supported.

 

Hiace 2.8TD P5-UDS (1GD-FTV/R7F701216) [THU/PO/NC]

 

13. In module 97 "China's AECS/LinControl ECU", support has been added for the G-Tech GT-54 ECU used in Jetour vehicles, the AECS FC-54 ECU used in Chery vehicles, the AECS FC-60 ECU used in JAC vehicles, and test support for the LinControl LEC4HE ECU used in Linxys vehicles. It supports reading, writing, checking, and correcting checksums.

 

Chery 1.5T E4T15C (AECS FC-54) [THU/PO/CS]

JAC 2.0T (AECS FC-60) [THU/PO/CS]

Jetour 1.5T E4T15C (G-Tech GT-54) [THU/PO/CS]

 

14. Module 99 "Service mode of the EMS 2.3/2.4 ECU for Volvo/Renault trucks" now fully supports all known ECU variants EMS2.3 and EMS2.4.