BitEdit Modules

Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars. Supported file size is 1.46 MB. Available the following cards: Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction Boost control: the boost controller duty cycle base, in regeneration, in the double injection mode, with a disabled EGR, the m..

In stock

Bosch EDC17CP02

Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars. Supported file size 4MB. Available the following cards: Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction Boost control: the boost controller duty cycle base, in regeneration, in the double injection mode, with a disabled EGR, the maximal ..

In stock

Bosch EDC17CP09

Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars. Supported file size 4MB. Available the following cards: Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction Boost control: the boost controller duty cycle base, in regeneration, in the double injection mode, with a disabled EGR, the maximal ..

In stock

Bosch EDC17CP45

Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74. Available the following cards: The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during acceleration/deceleration, the composition of the mixture, coeff. warm-up, Rev XX on the coolant temperature, the optimum ignition timin..

In stock

Bosch M17.8.7/ME17.9.74

Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)! Supported file size 7.5 MB. A list of available maps: Control air mass: expected mass air flow correction flow Pressure boost: the desired boost pressure, the limit boost pressure, PWM boost controller and its limits ..

In stock

Bosch MD1

$415.79

In stock

Bosch ME(D)(G)17.9.8

Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles. Available maps: The filling: Ripple sensor mass air flow, the calculated content Control boost the Efficiency of the compressor and the turbine, Isobaric heating process in the turbine Correction according to the temperature of the EXHAUST gas: the Correction of the lea..

Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai. Available the following cards: Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the throttle The temperature fan switch XX: XX desired speed for automatic transmission, manual transmission, when driving Contr..

In stock

Bosch ME(G)17.9.1 x

Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai. Available maps: The filling: Ripple sensor mass air flow, the calculated content Correction according to the temperature of the EXHAUST gas: the Correction of the lead angle on the temperature of the EXHAUST gas static temperature of the EXHAUST gas The injection Angle of..

In stock

Bosch ME(G)17.9.2x

Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5. You can edit the following cards: calculation of the mass of air and mass flow through the throttle momentum XX enrichment and obedienee during acceleration and deceleration phase control injection control of the composition of the mixture th..

In stock

Bosch ME17.8.5

Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production. Supports the following cards: Control the mass of air: mass flow rate through the throttle, the throttle position, the map of the accelerator pedal Pressurization: control valve boost request, linerization, P-component, the basis of regula..

In stock

Bosch ME17.8.8

Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market. Supported maps: Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal, Throttle valve position from airmass flow Boost control: Turbo compressor efficiency, Warmup isobar process for charger ..

In stock

Bosch MED17.8.10

Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles. You can edit the following cards: Idle speed: the Rpm of the twentieth Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correction Factors for atmospheric pressure, advance angle at the start, the Coefficients of correction of the fuel supply at start-up ..

In stock

Bosch MSE 3.0

$118.80

In stock

Bosch MSE6.0/US6.0

Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs Available maps: Air control: Pulsation correction for mass air flow in additional mode Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error, Target air filling calculated, Throttle valve position from airmass flow Airmass calculation: efficiency: Exhaust gas rest pr..

$244.94

In stock

CFMoto Bosch ME(D)17.8.10

Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles. The following calibrations are available for editing: Air Control: Accelerator pedal map Boost limiters: Boost limitation by coolant temperature, Boost limitation from engine speed, Boost limiter to prevent overspeed Exhaust gas model: Exhaust gas temperature, Exhaust gas temperature 2 ..

Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb. The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters, the maximum power of the engine and correction of power control XX in different modes, the fuel supply, the composition of the mi..

In stock

Continental GPEC (SIM90)

$118.80

In stock

Continental GPEC2

Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb. The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the constraints on the mass of air, lambda regulation, management of XX in different modes, control..

Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A. ..

In stock

Continental GPEC2A

Module for the calibration firmware different motorcycles BRP, Ducati, Arctic Cat, Stels, Dinli, etc. with the control units Continental M3C. Available the following cards: The calculated mass air flow to throttle position, correction of the estimated air flow correction volumetric efficiency of the intake, correct air flow from the external pressure, the delay of injection to the injectors, the basic ign..

In stock

Continental M3C

Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles. You can edit the following cards: Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow from torque Boost control: calculated charger speed, maximal boost pressure, minimal pressure boost, pressure ratio, wastegate ..

In stock

Continental SIM2K-24x

Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles. Available maps: Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode Driver request: Driver interpretation map Exhaust camshaft position: Exhaust camshaft position setpoint Exhaust gas temperature model:..

In stock

Continental SIM2K-26x

Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1. A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation of the usr, the calculation of the injection time, the composition of the mixture to limit the opacity, the pressure in the rail a..

In stock

Delphi DCM6.1

Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles. You can edit the following cards: Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of the XX with the XX, correction at idle and poliestrowy correction, the composition of the mixture at partial and full load, the R..

In stock

Delphi MT05

$118.80

In stock

GM ACDelco E92

Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.) You can edit the following cards: Fan Control: the Desired FAN control, FAN control via Desired coolant temperature Fuel: AFR target value as stoichiometry, Dynamic Airflow High RPM, Dynamic Airflow High RPM, Mass air flow sensor scaling Fuel:Injector: Injector F..

Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3. For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculation of the pressure controller the boost of efficiency, the expected position of the boost controller, the boost limit by the temper..

In stock

Honda Bosch Petrol Turbo

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental . It supports all the Continental blocks with the Motorola processor MPC5554 2Mb. We provide the following card for editing: Control of valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors,the threshold determination of full load, compensation for fuel tempe..

In stock

Honda Continental

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi. All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb. We provide the following card for editing: Control of valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors,the threshold determination o..

In stock

Honda Hitachi

Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi. Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo. Maps available: the expected boost pressure, boost limiter, the position of the control valve the boost phase of the camshaft, the correction of the injectors, the pressure at the inlet to deter..

In stock

Honda Hitachi 0.66 Turbo

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin. It supports all blocks Keihin processor SH7058, SH72543, MPC5566. Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors,the threshold determination of full load, compensation for fuel temperature, the composition of the mixtu..

In stock

Honda Keihin

$593.98

In stock

Honda Keihin 1.5 NA

Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor. Supported file size: 2.5 MB Supported Maps: Air Calculation: Air Charge Efficiency High VTEC, Air Charge Efficiency Low VTEC, Airmass flow through throttle body in additional mode, Exhaust back pressure after catalyst, Airmass flow thro..

$115.75

In stock

Honda Keihin 1.5 Turbo

Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin. Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maximal boost by atmospheric pressure, intake boost by maximal temperature, maximal ratio boost, desired boost pressure, exhaust back ..

$475.18

In stock

Honda Keihin 2.0 Turbo

Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin. Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maximal boost by atmospheric pressure, intake boost by maximal temperature, maximal ratio boost, desired boost pressure, exhaust back ..

$475.18

In stock

Honda Keihin 2.3 Turbo

Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb. Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors, the threshold determination of full load, compensation for fuel temperature, the composition o..

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita. Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543. We provide the following card for editing: Control of valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors,the threshold determination of full load, compensation f..

In stock

Honda Matsushita

A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units. Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An indicative set of cards has been grouped by type and presented below: R8C / H8C 32..128Kb: Axis conversion ..

In stock

Honda Moto Keihin

$593.98

In stock

Honda Motorola

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB. Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the opening time of the injectors,the threshold determination of full load, compensation for fuel temperature, the composition of th..

Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Panasonic processor Infineon Tricore TC197X with internal flash memory 4Mb. ..

In stock

Honda Panasonic

Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering. ..

In stock

Honda Petrol Full

$3 207.49

In stock

Isuzu Transtron Aurix

Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines. Supported maps: Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pressure in additional mode, Maximum Boost Limit, Maximum Turbo Position Limit, Turbo position in additional mode DPF: DPF Bo..

Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles. Supported maps: Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, Target Boost Maximum, Target Turbo Boost, Turbo Boost DPF: DPF Target Rail Pressure, ITH Target Position DPF, Target Boost DP..

In stock

Isuzu Transtron Delphi

Isuzu Transtron SH7058/SH7059

In stock

Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059. Supported filesize - 1Mb and 1.5Mb. Supported maps: Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant, Target Boost Intake Air Temperature Compensation, Target Boost Max/ Target Turbo Boost DPF: DPF Target Rail ..

Isuzu Transtron SH72533/SH72544

In stock

Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544. Supported filesize - 2Mb and 2.5Mb. Supported maps: Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant, Target Boost Intake Air Temperature Compensation, Target Boost Max/ Target Turbo Boost D..

Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles. Available maps: The filling: Ripple sensor mass air flow, the calculated content Control boost the Efficiency of the compressor and the turbine, Isobaric heating process in the turbine Correction according to the temperature of the EXHAUST gas: the Correctio..

In stock

Kefico CPEGD2/CPGDSH2

Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx. Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase injection, the limit engine speed, set pressure intake map pressure recovery at the inlet, the calculation of the efficiency of the ..

In stock

Marelli 8Gx Petrol Turbo

Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6. Idle speed in all modes The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the moment to limit the power of The knock control correction angle, the sensitivity of the knock sensors, map to determine bad/good..

In stock

Marelli IAW 9GV

Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles. We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads, calculation of time, the requested torque, relative torque, and limiting torque and the ignition timing and the correction angle ..

In stock

Marelli IAW7GFR

Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB. To adjust available the following cards: The injection correction injection for IDENTITY, and control of the injection phase at start-up Idle speed in all modes The friction torque and mechanical loss torque, the requested torque in different modes and on different gears..

In stock

Marelli IAW7GV

Mazda Denso Petrol SH705x

In stock

Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058. You can edit the following cards: Air load: engine load limitation, load correction for MAF Configuration: engine volume, dwell time, MAF scaling EGR: EGR target position Idle: desired idle speed Injection: target AFR at open loop, the target AFR at closed loop, load threshol..

Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D. Editable the following cards: Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boost EGR control: mass air flow voltage valve EGR Injection volume: conversion of point in the injection volume in differ..

In stock

Mazda Denso SkyActiv-D

Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters. Editable the following cards: The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts, the enrichment in the control mode and power mode, the threshold pedal position to switch to power mode, the request is the throt..

In stock

Mazda Denso SkyActiv-G

Mazda Mitsubishi 2.3 Turbo

In stock

Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor. Available the following cards: Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure limitation, maximal intake pressure, wastegate duty Calculated EGT Idle: desired idle speed in drive,desired idle spee..

Mazda Mitsubishi SkyActiv-G

In stock

Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters. Editable the following cards: The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts, the enrichment in the control mode and power mode, the threshold pedal position to switch to power mode, the request is the throt..

Mitsubishi Denso Diesel SH7058

In stock

Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi. Supported file size is 1Mb. You can edit the following cards: Air mass: the expected air mass, the expected mass of air with EGR off Boost control: the limitation of temperature boost charge air, limiting the boost, the expected boost pressure, PWM valve pressurization Inje..

Mitsubishi Denso Diesel SH7059

In stock

Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi. Supported file size - 1.5 MB. You can edit the following cards: Air mass: the expected air mass, the expected mass of air with EGR off Boost control: the limitation of temperature boost charge air, limiting the boost, the expected boost pressure, PWM valve pressurization In..

Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb. The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the constraints on the mass of air, lambda regulation, management of XX in different modes, control the injector, the correction to the PW..

In stock

Motorola NGC4

Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb. The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the constraints on the mass of air, lambda regulation, management of XX in different modes, control the injector, the correction to the P..

In stock

Motorola NGC4A

Nissan Denso Diesel SH7058

In stock

Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan. Supported file size is 1 MB. Available the following cards: Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in different conditions, smoke limitation, time of injection from the pressure in the rail, the injection of the additional calibrat..

Nissan Denso Diesel SH7059

In stock

Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan. Supported file size - 1.5 MB. Available the following cards: Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in different conditions, smoke limitation, injection time, calibration of the sensors the IDENTITY of the air flow sensor, EXHAUST ..

Nissan Hitachi Petrol Full

In stock

A set of 7 modules to edit all available petrol cars Nissan and infiniti with the control units from Hitachi. 15% savings when ordering the kit. The list of modules includes: Nissan Hitachi Petrol Gen1 SH7054 Nissan Petrol Gen1 Hitachi SH7055 Nissan Hitachi Petrol Gen1 SH7058 Nissan Petrol Gen1 Hitachi SH7059 Nissan Hitachi Petrol Gen1 SH72xx Nissan Hitachi Petrol Turbo Gen1 N..

$1 615.62

In stock

Nissan Hitachi Petrol Gen1 SH7054

Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti. Supported size firmware 384Кб. Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the mode of regulation and the basic composition of the mixture, the compensation of the fuel in the mixture, calibration MAF base..

Nissan Hitachi Petrol Gen1 SH7055

In stock

Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars. Supported size 512 KB firmware. Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the mode of regulation and the basic composition of the mixture, the compensation of the fuel in the mixture, calibration MAF bases Q..

Nissan Hitachi Petrol Gen1 SH7058

In stock

Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars. Supported firmware size of 1MB. Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the regulatory regime and the underlying composition of the mixture, the phase of the intake shaft, the compens..

Nissan Hitachi Petrol Gen1 SH7059

In stock

Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars. Supported firmware size 1.5 MB. Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation of the fuel in the mixture, calibration MAF bases QH0, the basic setting of the throttle, the sensitivity of the knock sensors, tri..

Nissan Hitachi Petrol Gen1 SH72xx

In stock

Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti. Supported size 2.0 firmware MB. Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation of the fuel in the mixture, calibration MAF bases QH0, the basic setting of the throttle, the sensitivity of the knock sensors,..

Nissan Hitachi Petrol Gen2

In stock

Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB. Editable the following calibration: sensitivity Control PID-boost regulator correction according to the degree of pressurization, the specified charge restriction charge correction time of injection, the conversion of the mixture to the..

Nissan Hitachi Petrol Turbo Gen1

In stock

Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR). Supported file MCU Renesas SH7058 size 1.0 MB. Available the following cards: The specified boost pressure, multiplier to limit and boost cut-off, the calculation of the relief valve of the boost from the speed and pressure, given a PWM for valve control the boost, the estimated temperatur..

Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia. This module provides a set of cards is sufficient to create the modified files at any Stage: Control boost PWM control valve boost limit the boost and MAF, threshold of time to start regulating boost The limitation engine speed (cut-off) Management XX: XX desired speed in the D position and ..

In stock

Renault Siemens EMS3150

Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71. Available the following cards: The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficiency for the calculation of injection mass of fuel by the throttle position, a correction on the warm-up, compensation injection at ..

In stock

Siemens MSE 3.7

Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17. To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control boost regulator to control injection timing, number of injection, the conversion time in number, the limit number, the controller..

In stock

Toyota Bosch Diesel

Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi. Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size). The efficiency of the intake: the intake efficiency of the intake and vypusnogo shafts, the correction efficiency on engine speed, load calculation Injection: injection correction when the lambda regu..

In stock

Toyota Delphi Petrol

The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx. You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more accurate settings you can also control corrections and limiters main parameters of engine operation, and contr..

In stock

Toyota Denso Diesel 1

The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx. You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more accurate settings you can also control corrections and limiters main parameters of engine operation, and control of actuators(pres..

In stock

Toyota Denso Diesel 2

The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx. You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more accurate settings you can also control corrections and limiters main parameters of engine operation, and control of actuators(pressu..

In stock

Toyota Denso Diesel 3

The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085). Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit, control of the turbine geometry, the pressure in the rail limiters, torque limit, control the advance and duration of injection ..

In stock

Toyota Denso Diesel 4

Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD. The module supports firmware files: MCU D76F0196F1 1536Kb MCU D76F0219F1 2048Kb You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more accurate settings you can also control..

In stock

Toyota Denso Diesel 5

Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines . Supported filesize: 4Mb. Available maps: Air calculation: Air flow correction, Desired air calculation, Desired air calculation in additional mode Boost Pressure: Base boost pressure in additional mode, Base boost pressure with active EGR Boost P..

In stock

Toyota Denso Diesel 6

Set of 5 modules 1,2,3,4,5 Toyota Denso Diesel. Allows you to edit all available diesel cars are Toyota, Lexus, Hino on the units of DENSO. 10% savings when ordering. ..

In stock

Toyota Denso Diesel FULL

$1 389.91

In stock

Toyota Denso FULL

Set of 15 modules Toyota Denso Diesel 1,2,3,4,5 + 1,2,3,4,5,6 Petrol + turbo Petrol + OLD + Gearbox+ GT86. Allows you to edit all the available vehicles Toyota, Lexus, Scion, Hino on the units of DENSO. 15% savings when ordering. ..

$3 736.13

In stock

Toyota Denso Gearbox

The module allows you to adjust the transmission of Toyota, Lexus, in which the control program resides in a separate processor NEC 76F0040AGD. We offer to edit the following settings of the transmission conditions for the transmission shift up and down, control pressure switch, overall oil pressure, the expected switching time, as well as the calibration of the oil temperature sensor in the box ..

$593.98

In stock

Toyota Denso Petrol 1

The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the correction angle of the camshaft position for the VVT, maps, en..

The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the correction angle of the camshaft position for the VVT, maps, enr..

In stock

Toyota Denso Petrol 2

The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the correction angle of the camshaft position for the VVT, maps, enrichment and correction of injection, throttle, re..

In stock

Toyota Denso Petrol 3

The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085. Currently it supports the following cards: Air calculation: Calculated air load from requested torque, Mass air flow pulsations factor Automatic transmission down..

In stock

Toyota Denso Petrol 4

The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the correction angle of the camshaft position for the VVT, maps, enrichment and correction of injection, throttle, requested torque at..

In stock

Toyota Denso Petrol 5

The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the correction angle of the camshaft position for the VVT, maps, enrichment and correctio..

In stock

Toyota Denso Petrol 6

Set of 8 modules 1,2,3,4,5,6 Petrol Toyota Denso, Toyota Denso Toyota Denso OLD and Petrol Turbo. Allows you to edit all available petrol cars are Toyota, Lexus, Scion on the units of DENSO. 10% savings when ordering. 10% savings when ordering. ..

In stock

Toyota Denso Petrol FULL

$2 031.41

In stock

Toyota Denso Petrol Old

An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB. Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only possible via the diagnostic connector. Read-only virtual with the corresponding module Bitbox. Supported engine: 1AZF..

Toyota Denso Petrol Turbo

In stock

Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB. Supported models: Lexus NX 200t Lexus IS 200t Lexus GS 200t Lexus RX 200t Toyota Crown 2.0 t etc. Supported engines: 8AR-FTS ..

Toyota Denso Yaris GR Turbo

In stock

Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine. Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing Only 4MB files are supported. The following MCU1 8 A 230-52 XXX cards are available: Air control: Efficiency in additional mode, Maximal mass air flow Boost control: l..

Toyota GT86 / Subaru BRZ Denso SH72531

In stock

Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S. Available maps: The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the expected turnover of the twentieth, the enrichment in acceleration to throttle position, as well as correction factors of enrichment..