CombiLoader Modules

Designed for chip tuning of ECU Abit M20.20, M20.21, M240, M240S1, MD22. Modules allow you to: - Read and write calibration area - Read and write control program - Calculate and, if necessary, automatically correct the checksum of the calibration area - Perform ECU identification - Read and reset fault codes ..

In stock

Abit M20.21/M240/MD22

Module ACDelco Delphi intended read / write FLASH memory of ECU Delphi ACDelco E37/E38/E39/E67/E78/E83 installed on Chevrolet and Opel via the diagnostic connector. Table of applicability ACDelco E37 (2.4 L — LE5/LE9): Chevrolet Captiva (C140) 2011+ Opel Antara 2011+ Table of applicability ACDelco E38 (4.8 L — part no ly2; 5.3 L — LY5/LC9/L45; 6.0 L — LQ4/L92/L76; 6.2 L — L92/L94/L9H): ..

In stock

ACDelco Delphi

Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector. ..

In stock

ACDelco Siemens

Attention! This module works in conjunction with CombiLoader 2.16 or later. The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector. The module automatically corrects CS calibrations during recording. The J2534 adapter, purchased separately, is required for operation. ..

In stock

AECS UAZ

The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector. Module is the automatic correction of the COP calibration during the recording. Work with the J2534 adapter, sold separately. ..

In stock

AMT WHA

The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector. Module is the automatic correction of the COP calibration during the recording. Work with the J2534 adapter, sold separately. ..

In stock

AMT WHA

Bosch EDC16 Bosch ME9 BSM and BSM (J2534) (set)

In stock

The modules are designed to read / write the FLASH/EEPROM of the ECU series Bosch EDC7/EDC16/PSG16/ME9 without opening. The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details. The module does not support the ECU family ME9 following manufacturers: BMW. Supported file formats: Uncompressed BIN (plain bin..

Bosch EDC17CV44/54 (J2534)

In stock

The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector. Work with the J2534 adapter, sold separately. The module performs automatic recalculation of the COP. ..

The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector. Work with the J2534 adapter, sold separately. The module performs automatic recalculation of the COP. ..

In stock

Bosch EDC7UC31 (J2534)

The module allows you to write firmware diagnostic method, without removing the ECU from the vehicle through the DLC (to work with the ECU on the car must be connected directly to the connector of the UNIT to disassemble the unit is not required). Support ECU Bosch MSE3.0, M7.9.7, ME7.9.7, M7.9.71(M7.9.7+), M7.8, ME7.8.8. ..

In stock

Bosch M(E)7.x (OBDII)

Kia, Hyundai, equipped with ECU Bosch M(G)7.9.8. Designed for recording FLASH memory ECU Bosch M7.9.8 and MG7.9.8 via the diagnostic connector without removing the ECU from the vehicle. ..

In stock

Bosch M7.9.8 (J2534)

The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU. Please note: Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections in accordance with the type of ECU. The module is provided in two options: working through the adapter Loader and adapter J..

In stock

Bosch ME17.9.x VAZ/UAZ

Bosch ME17.9.x VAZ/UAZ for users of J2534 module BSL TC17xx

In stock

The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU. Please note: Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections in accordance with the type of ECU. The module is provided in two options: working through the adapter Loader and adapter J..

$43.81

In stock

Bosch ME9.x GM J2534 and the Bosch ME7.9.9 J2534 (kit)

The modules are designed to read / write FLASH Chevrolet/Opel/Cadillac/SAAB, equipped with ECU Bosch ME9.x and the Bosch ME7.9.9 via the diagnostic connector. Work with the J2534 adapter, sold separately. Module is a Bosch ME9.x GM makes automatic recalculation of the COP recorded calibrations. ..

The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45. Bosch ME17.2.1/ME17.4.5, MEV17.2.1/MV17.4.6, MEVD17.2, MEVD17.2.2. Module is the automatic correction of the COP calibration during the recording. Re..

In stock

Bosch MEDC17 BMW Exx

$233.67

In stock

Bosch MEDC17 BMW Exx for users 2 or 3 version of module BSL TC17xx J2534

The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45. Bosch ME17.2.1/ME17.4.5, MEV17.2.1/MV17.4.6, MEVD17.2, MEVD17.2.2. Module is the automatic correction of the COP calibration during the recording. Re..

The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening. The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details. Module is the automatic correction of the COP while recording. Module is not supported to work with ECUS without internal FLASH, TPROT above 3 TC1766/TC1796 ECU with the Chinese ON. ..

In stock

Bosch MEDC17 BSM (J2534)

Bosch MEDC17 BSM (J2534) for users 3 version of module BSL TC17xx J2534

In stock

The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening. The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details. Module is the automatic correction of the COP while recording. Module is not supported to work with ECUS without internal FLASH, TPROT above 3 TC1766/TC1796 ECU with the Chinese ON. ..

Bosch MEDC17 Hyundai/Kia and Bosch MEDC17 Hyundai/Kia UDS (kit)

In stock

The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector. Is free app for all users 2 or 3 version of module BSL TC17xx J2534. Module Bosch MEDC17 Hyundai/Kia supported the following types of ECUS: (read/write) Bosch EDC17C08 (read/write) Bosch EDC17CP14 (TPROT3) (read/write) Bosch EDC17CP14 (TPR..

Bosch MEDC17 PSA, SID807 PSA (kit)

In stock

The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector. The modules support the following types of ECUS: Bosch EDC17C10 (CPU TC1797) Bosch MED17.4 (CPU TC1766) Bosch MEV17.4 (TC1796 processor and external memory) Bosch MEV17.4 (CPU TC1766) Bosch MEV17.4.2 (TC1767 processor) ..

Bosch MEDC17 PSA, SID807 PSA (set) for users 2 or 3 version of Module BSL TC17xx J2534

In stock

The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector. The modules support the following types of ECUS: Bosch EDC17C10 (CPU TC1797) Bosch MED17.4 (CPU TC1766) Bosch MEV17.4 (TC1796 processor and external memory) Bosch MEV17.4 (CPU TC1766) Bosch MEV17.4.2 (TC1767 processor) ..

The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector. The module supports the following types of ECU: Bosch ME17.9.5. Bosch ME17.9.51. Bosch ME17.9.6. Bosch ME17.9.61 (recording after CPU shutdown). The module automatically corrects CS calibrations during recording. Supported f..

In stock

Bosch MEDC17 Suzuki

Bosch MEDC17 Suzuki for users 2 or 3 version of module BSL TC17xx J2534

In stock

The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector. The module supports the following types of ECU: Bosch ME17.9.5. Bosch ME17.9.51. Bosch ME17.9.6. Bosch ME17.9.61 (recording after CPU shutdown). The module automatically corrects CS calibrations during recording. Supported f..

Bosch MEDC17 VAG K/CANTP2.0

In stock

The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24. Bosch MED17.1, MED17.1.1, MED17.5, MED17.5.1, MED17.5.2, MED17.5.5, MED17.5.6, ME17.5.20. Module is the automatic ..

Bosch MEDC17 VAG K/CANTP2.0 for users 2 or 3 version of module BSL TC17xx J2534 or module Bosch MEDC17 VAG UDS

In stock

The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24. Bosch MED17.1, MED17.1.1, MED17.5, MED17.5.1, MED17.5.2, MED17.5.5, MED17.5.6, ME17.5.20. Module is the automatic ..

The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17CP54, EDC17C46, EDC17C54, EDC17C64, EDC17C74 Bosch MED17.1, MED17.1.1, MED17.1.6, MED17.1.21, MED17.1.27, MED17.5, MED17.5.5, MED 1..

In stock

Bosch MEDC17 VAG UDS

Bosch MEDC17 VAG UDS for users 2 or 3 version of module BSL TC17xx J2534

In stock

The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector. The module supports the following types of ECUS: Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17CP54, EDC17C46, EDC17C54, EDC17C64, EDC17C74 Bosch MED17.1, MED17.1.1, MED17.1.6, MED17.1.21, MED17.1.27, MED17.5, MED17.5.5, MED 1..

The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, if necessary, automatically correct the checksum of the calibrations area - Identify the ECU - Read and clear fault codes - Add pr..

In stock

Bosch MG1 China

The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles. ..

In stock

Bosch MSE6.0

The module is designed for reading and writing FLASH/EEPROM ECUs based on ST/Motorola/FreeScale/NXP processors of the SPC5/MPC5xxx families via the built-in BAM (BootAssistModule). Such ECUs include, for example: Delphi ACDelco E78 Delphi ACDelco E83 Delphi DCM6.2 Delphi MT62.1 SID605/WISE15/WISE15C Other types of ECUs with processors of the SPC5/MPC5xxx families Th..

In stock

BSL mode SPC5/MPC5xxx

BSL TC17xx J2534 limited entry only ECU Bosch M(E)17.9.7 VAZ and UAZ, without recalculating the checksum of the firmware

In stock

The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader. To this type are (read/write/unlock): ME17.9.7, VAZ, UAZ M(E)17.9.71, TPROT 12, UAZ (new!) Read-only format ChipTuningPRO 7: ME17.9.11/12, Hyundai, Kia Siemens SIM2K-2xx Continental EMS2204 Delphi MT..

BSL TC17xx J2534 with no restrictions on entry with recalculation of the checksum, keeping the firmware in open format

In stock

The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader. To this type are: ME17.9.7, VAZ, UAZ M(E)17.9.71, TPROT 12, UAZ (new!) ME17.9.11/12, Hyundai, Kia Siemens SIM2K-2xx Continental EMS2204 Delphi MT80 Delphi SID-208 Different ECU MED17 family ..

BSL TC17xx J2534 with no restrictions on entry without recalculating the checksum of the firmware, keeping the firmware in a proprietary format SMS-BIN

In stock

The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader. To this type are: ME17.9.7, VAZ, UAZ M(E)17.9.71, TPROT 12, UAZ (new!) ME17.9.11/12, Hyundai, Kia Siemens SIM2K-2xx Continental EMS2204 Delphi MT80 Delphi SID-208 Different ECU MED17 family ..

Continental DC4 TCM and Continental TA2005 TCM (kit)

In stock

Set of modules (General license): Continental DC4 TCM Continental TA2005 TCM The modules are designed to read / write calibrations and programs of the DC4/TA2005 TCM ECU installed on Renault vehicles via the diagnostic connector. Additional function: Calculation of the CS of the calibration area. Identification of the ECU. Recording the ECU VIN code (TA2005). ..

Continental EMS2204 Ford J2534

In stock

The module is intended for recording and(or) region calibration ECU Siemens EMS2204, installable in particular on cars Ford Focus 3 engine 1.6 l ..

Continental EMS3110/3120/3125 Renault J2534

In stock

Cars Renault Logan 2, Sandero 2, Fluence, Megane 3, Latitude, Duster.. Designed to read and record the calibration and program the ECU mounted on Renault cars via diagnostic connector. ..

Continental EMS3180 Renault J2534

In stock

It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector. Additional functions: Calculation of the CS of the calibration area. ECU identification: allows you to request the identification data of the ECU. To work with the EMS 3180 ECU, which includes full access to FLASH/EEPROM, an extension of the module's cap..

Continental SIM2K-SIM2K and 25x-26x (J2534) (set)

In stock

Modules are designed for reading and writing the ECU Continental SIM2K-250/251/253/258/259/260/261, installed in Hyundai/Kia vehicles. The work can be done with ECU opening, without ECU opening (after preparation), or in diagnostic mode (functions such as identification, error reading/reset, and software and/or calibration writing are available). The module automatically recalculates the checksum of the written calibrations..

Designed for reading and writing FLASH memory of Cummins CM876/CM2150/CM2220(/C)/CM2880/CM2350(/A)/CM2620D1/CM2670(A/C/D/E/F) ECUs installed in vehicles such as GAZ/MAZ/KAMAZ and others through the diagnostic connector. The module also includes a flexible mechanism for reading and writing ECU configuration parameters. If the ECU performs a digital signature check, it can only be written with original software. This applies ..

In stock

Cummins CMx J2534

Delphi DCM3.7 SsangYong Delphi DCM3.7 GM, Delphi DCM3.7 GreatWall, Delphi DCM3.7 Hyundai/Kia Delphi DCM3.7 VAG (kit)

In stock

The set of modules (General license): Delphi DCM3.7 SsangYong Delphi DCM3.7 GM Delphi DCM3.7 GreatWall Delphi DCM3.7 Hyundai/Kia Delphi DCM3.7 VAG The modules are designed to read / write FLASH memory of ECU Delphi DCM3.7, mounted on SsangYong, Opel, Chevrolet, Great Wall, Kia, Hyundai and VAG group via the diagnostic connector. Extra features: The calculation of ..

It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector. Additional functions: Calculation of the CS of the calibration area. ECU identification: allows you to request the identification data of the ECU. Reading and resetting errors. ..

In stock

Delphi DCM6.2 China

Designed to read/write calibration and program the ECU Delphi DCM6.2/6.2A/6.2C installed on the Peugeot/Citroen via the diagnostic connector. Extra features: The calculation of the COP of field calibrations. Identification of control UNIT: allows you to request identification data of the ECU. Read and reset errors. ..

In stock

Delphi DCM6.2 PSA

The module is designed for reading and writing software and calibrations of the Delphi DCM 6.2V ECU of VAG group cars via UDP protocol via the diagnostic connector. The module automatically corrects CS calibrations during recording. The module supports the "Virtual reading" function of the ECU. The ECU is read when connected "on the table" without opening the ECU. ..

In stock

Delphi DCM6.2V VAG

Chevrolet (Lacetti, Epica, Tacuma, Rezzo, Spark) and Daewoo. ..

In stock

Delphi MR140/HV240 Ext

$182.56

In stock

Delphi MT05 and FAI-CR

Module MT-05 Designed for chip tuning of Delphi MT05 and Delphi MT05.2 ECUs installed on various types of motorcycles. Delphi MT05 and MT05.2 control units differ in the type of processor used and the size of FLASH memory. For Delphi MT05, the FLASH size is 128KB, for Delphi MT05.2 - 256KB. The type of ECU is determined automatically by the module. Supports reading the full FLASH image, writing software/calibrations, workin..

The cars of Chinese production (Great Wall Hover, BYD, etc.) with Delphi MT20U ECU, MT20U2, MT20UED, MT22U and MT22.1. Supported read and write FLASH and EEPROM. ..

In stock

Delphi MT20

Delphi MT34 China J2534, Delphi MT80 China J2534, Delphi MT92 Great Wall J2534 (kit)

In stock

Modules allow you to produce a chip tuning (reading and writing FLASH) ECU Delphi MT34, Delphi MT80 and Delphi MT92 vehicle Great Wall/Haval/Geely, via the diagnostic connector. Work with the J2534 adapter, sold separately. ..

Delphi MT80 + MT60 empowerment

In stock

The modules operate only in conjunction with the base module Delphi MT60/MT80 and designed for read-write full image of ECU Delphi MT60/MT80 diagnostic method using the J2534 interface. ..

It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector. It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector. Pay attention: Delphi MT22.5 ECUs have two different hardware modifications (externally identical): programmable by CAN: work with such ECUs is supported by this module programmab..

In stock

Deplhi MT22.x/MT62.1

DSI TCM / Continental DCT GreatWall / Continental EAST80.D1 / EAST80.F1 (complect)

In stock

Module kit: The module is designed to read/write FLASH memory of DSI TCM / Continental DCT GreatWall / Continental EAST80.D1 / EAST80.F1 vehicles via the diagnostic connector. The module performs automatic correction of the COP of calibrations during recording. The module is designed to write software / calibrations through the diagnostic socket. The module performs automatic correction of the COP of calibrati..

Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector. Extra features: The calculation of the COP of field calibrations. To change VIN: allows you to change the VIN code in the downloaded firmware. Identification of control UNIT: allows you to request identification data of the ECU. ..

In stock

EMS3130 J2534

EMS3130 J2534 for owners of the Sirius module 3x

In stock

Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector. The price shown is for the owners of the Sirius module 3x Extra features: The calculation of the COP of field calibrations. To change VIN: allows you to change the VIN code in the downloaded firmware. Identification of control UNIT: allows you to request identificati..

The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, there are no ways to recover the ECU after a failure. Be extremely careful when working with the ECU. Writing incompatible software or..

In stock

EMS31xx/SID321 Renault

Ford Extra empowerment modules Ford

In stock

The empowerment of Ford modules work with the ECU SID208/SID209(CK4A), including full access to the FLASH EEPROM through the diagnostic connector. ..

Ford Siemens SIM28/29 and Siemens SIM22/210 (kit)

In stock

The modules are designed to read / write flash memory of ECU Siemens vehicle Ford Focus 2, C-Max, Kuga engines 1.4...1.6 l (2004...2009), Ford Fiesta, Fusion engines 1.2...1.6 l ..

In stock

In stock

Isuzu Transtron J2534

Kit modules: Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector. Isuzu Transtron 7058 (J2534) Module is designed to read / write to K-line FLASH memory Transtron ECU based on Renesas SH7058 processor if the AT E..

The car is equipped with ECU January-7.2+, M73, M74K. Does not work with 'closed' versions of the ECU M73! ..

In stock

January-7.2+/M73/M74K

$43.81

In stock

M11/M73A

Cars equipped with ECU Mikas-11,ET(CR) and M73 with the latest version of the software. The module allows to work with the so-called 'closed ECU', which cannot work with standard modules Mikas-11/Mikas-11ET/Mikas-11CR/VS-8, January-7.2+/M73 or BSL. ..

Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN. ..

In stock

M74 K-Line + CAN

M74.8/M74.8+/M74.9 VAZ (set)

In stock

The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.9..

$131.44

In stock

M74.8/M74.8+/M74.9 VAZ (set) for M74.9 GAZ users

The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.9..

The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Soft Container File format. To edit such firmware, only CTPro editor should be used. An J2534 adapter, purchased separately, is requi..

In stock

M74.9 GAZ

$131.44

In stock

M74.9 GAZ for M74.8/M74.8+/M74.9 VAZ users

The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Soft Container File format. To edit such firmware, only CTPro editor should be used. An J2534 adapter, purchased separately, is requi..

The car 'Lada Vesta/XRay/Largus' with electronic gas pedal, equipped with ECU M86/M74M. The module is intended for read-write FLASH/EEPROM ECU М86 with a production of vases, based on the Infineon processor family XC27x5 via the built-in BootStrapLoader, and recording via the diagnostic connector. ECU programming is performed without disassembling the ECU. Work with the J2534 adapter, sold sep..

In stock

M86/M74M

MagnetiMarelli MM4HV/MM7GV VAG

In stock

The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices. The modules support the following types of ECUS: MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB. MagnetiMarelli MM7GV: petrol engines 1.4/1.6 l CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Module is the automatic correction of the COP calibratio..

The module is designed for reading and writing MCM2.1 D4/D5 ECUs installed on MercedesBenz trucks. The ECU can be operated both without opening in the OBD-Full mode, and with opening in BSL mode. Identification and error reading/reset functions are also available. The module automatically recalculates the values of recorded calibrations. The module allows you to fully read and write the con..

In stock

MCM2.1 Mercedes-Benz

$730.23

In stock

Mikas-10.3 (M103, M113)

Daewoo, ZAZ Ukrainian Assembly, GAS. ..

$58.42

In stock

Mikas-10.3 (M114)

Cars equipped with ECU M114 (new version ECU M10.3, is mounted on Daewoo Sens, GAZelle, etc.). ..

Autobile 'Volga', 'Gazelle', UAZ, equipped with ECU Mikas-Mikas 11b-11ET, Mikas-11CR or VS-8. Can be programmed without changes to the ECU. Does not work with 'closed' versions of the ECU! ..

In stock

Mikas-11/VS-8

Cars equipped with ECU М124 (new version ECU Mikas, for installation on automobiles GAZ.). ..

In stock

Mikas-12.3 (M124)

The module is intended for read / write FLASH and EEPROM ECU MIKAS-12, M74.5, M75 and M86 running programs production ELKAR/ITELMA installed on new cars UAZ and VAZ with electronic gas pedal. Features of the module: The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader). The possibility of opening a firmware in BIN format (normal binary). Save firm..

In stock

Mikas-12/M74.5/M75/М86И

The module is designed for reading and writing ECU MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90, installed on BMW cars. Work with the ECU is performed on the table without opening the ECU. Identification and error reading/reset functions are also available for the E-Series ECU. The module automatically recalculates the CS of recorded calibrations. ..

In stock

MSVD8x/90 BMW (J2534)

Renault Extra expansion capabilities of the modules Renault

In stock

The empowerment modules Renault to work with the ECU EMS3155/SID310, EMS3120/EMS3125/EMS3150 and SID307, including full access to FLASH/EEPROM. ..

The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector. ECU Continental EMS3155 is installed on the engines 1.2 T. ECU Continental SID309 is installed on the engines of 1.5 l . ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L. ECU Bosch EDC17C84 is installed on the engine 1.6 l To work with the EC..

In stock

Renault UDS (kit)

The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars. Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available. The module automatically recalculates the CS of recorded calibrations. The module allows you to fully read and write the contents of the ECU. ..

In stock

SDI9/10 Porsche (J2534)

SDI9/10 Porsche (J2534) for SDIx Porsche Module Users

In stock

The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars. Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available. The module automatically recalculates the CS of recorded calibrations. The module allows you to fully read and write the contents of the ECU. ..

The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles. Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available. The module does not support work with SDI7 ECU with hardware number 97061860202 (3.6l). The module automatical..

In stock

SDIx Porsche (J2534)

SID206 + SID208 + SID209 + SID211 Ford J2534 (kit)

In stock

The kit contains modules: Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L. Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particular on cars Ford Transit 2.2 L Diesel. Module SID209 designed for recording and(or) field calibration of the ECU SID209, ins..

Designed to read and record the calibration and program the ECU SID208 vehicle Peugeot Boxer/Citroen Jumper via the diagnostic connector. Extra features: The calculation of the COP of field calibrations. Identification of control UNIT: allows you to request identification data of the ECU. Reading ECU password: allows to read the ECU password to unlock BSL module TC17xx J2534. Read an..

In stock

SID208 PSA J2534

The module is designed for reading/writing software/calibrations of the SID212/EVO ECU installed on Ford vehicles. The ECU can be operated in the following modes: OBD: Read (1h50min ON/calibration, 38min calibration) and write (3min ON/calibration, 1min calibration) of the original ECU software/calibrations are available. Bench: Read (5min ON/calibrations, 2min calibrations) ON/calibrations and ..

In stock

SID212/EVO Ford (J2534)

SID301/305/306/307 Delphi DCM3.4, EDC17C11/42 Renault J2534 (kit)

In stock

The set of modules (General license): EDC17C11 Renault Bosch J2534 EDC17C42 Renault Bosch J2534 SID301 Renault J2534 SID305/306 Renault J2534 SID307 Renault J2534 Delphi DCM3.4 Renault J2534 The modules are designed to read/write and(or) field calibration of the ECU installed on the Renault/Nissan with diesel engines. Work with the J2534 adapter, sold separately. ..

SID605/WISE13H/WISE15/MD1/EQ EDC17CV54 J2534

In stock

It is designed for reading and writing software/calibrations of the SID605/WISE13H/WISE15/MD1/EQ EDC17 V6/V7 ECU installed on MAZ cars and Chinese-made cars via a diagnostic connector. The kit supports the following types of ECU: SID605: software/calibration recording. WISE15: Read-write software/calibrations. WISE15C: Read-write software/calibrations/configurations. Bosch MD1CC878/W..

The BMW cars with ECU Siemens MS41/42/43: E36/E38/E39/E46/E53 6-cyl 2.0 L — 3.0 L. ECU Programming can be performed directly on the vehicle through the diagnostic connector. ..

In stock

Siemens MS41/42/43

Siemens SIM2K C201/241/242/245 Siemens SIM2K 140/141/341/D160, Delphi MT38 and Delphi MT86 (kit)

In stock

ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong. Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle. Works through the J2534 interface. ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato, Carens, Sorento, Sportage), Hyundai (Sonata, IX35) with engines of 2.0 L and more, as well as the Chevrolet Epica. The modul..

Chevrolet Spark M300, TagAz Vega C-100. Designed for read-write calibrations and programs the ECU via the diagnostic connector. ..

In stock

Siemens SIM2K-D51/D52

The module is designed to read / write calibration and program control UNIT Siemens SIM2K-243 GM vehicle Chevrolet Spark M-300. The module allows reading and writing of programs or the field of calibrations, diagnostic method, without removing the ECU from the vehicle. Works through the J2534 interface. ..

In stock

Siemens SIMK2K-243 GM

Siemens SIMK43/41/31 J2534

In stock

Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN) ..

$87.63

In stock

Siemens SIMK43/41/31 J2534 for users of the module SIMK43/41/31

Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN) ..

Siemens SIMK43/41/31 K-Line

In stock

Kia, Hyundai, equipped with ECU Siemens SIMK43 and SIMK41, Chery QQ cars equipped with ECU Siemens SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface) ..

$58.42

In stock

Siemens SIMTEC70, SIMTEC7x, Bosch M7.6.x, Bosch M7.9.7.1, PSG16, Bosch and Delphi MT35E for chip tuning Opel cars (complete set)

The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector. Table of applicability ECU SIMTEC 70: Opel Astra G (1998-2000) X18XE1/X20XEV Opel Vectra B (1998-2001) X18XE1/X20XEV Opel Zafira (1999-2000) X18XE1 The module is designed SIMTEC7x read / write FLASH memory of ECU Siemens SIMTEC71.x SIMTEC75.x and SIMTEC8..

Chevrolet (Lacetti, Epica, Tacuma, Rezzo), Daewoo (Matiz). ECU programming can be performed directly on the vehicle through the diagnostic connector. ..

In stock

Siemens Sirius D3x/D4x

The cars of Chinese production Lifan, Breeze, etc. is Designed to read / write FLASH and EEPROM ECU Siemens Vagon VAx ..

In stock

Siemens Vagon VAx

$58.42

In stock

Siemens VDO MSE3.5

RoadPartner cars TagAz/TaGeR/SsangYoung Rexton with engines 2.3/2.8/3.2 L. Intended for read-write FLASH memory via the diagnostic connector. ..

SIM271DE 2.0 MercedesBenz (J2534)

In stock

The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles. Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors. The module performs automatic recalculation of the COP recorded calibrations. The module allows full read and write the conte..

SIMOS12/16/18 VAG J2534 (complect)

In stock

The modules are designed for reading and writing the SIMOS12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECU installed on VAG vehicles. Work with the SIMOS12.1/12.2 ECU is performed on the table without opening the ECU. Работа с ЭБУ SIMOS16.11 is performed on the table with the ECU openin Work with the SIMOS18.1/18.2 ECU is performed on the table with the ECU opening. Identification and error reading/resetti..

Allows you to work with Renault Clio/Megane/Scenic/Logan, equipped with systems Sirius32/EMS3132/Sirius34/EMS3134. ECU programming directly on the vehicle through the diagnostic connector. The main difference from similar applications is the ability to read/write programs for a replacement. Issued for the replacement module Siemens EMS3132 for users module Siemens EMS3132 update free. ..

In stock

Sirius 3x

The Bosch ME7.4.4 Bosch ME7.4.5, Valeo V46 and Valeo J34P (kit)

In stock

The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector. Work with the J2534 adapter, sold separately. Extra features: Identification of control UNIT: allows you to request identification data of the ECU. Read error: reads from the ECU the number of DTCs and displays their codes. Initialization: allows initializi..

The Delphi MT60 J2534, Delphi MT80 J2534, J2534 Siemens SIMTEC76 (kit)

In stock

Daewoo Gentra (Delphi MT60), Chevrolet Aveo, Chevrolet Cruze (Delphi MT80), Chevrolet Cruze, Daewoo Lacetti (Siemens SIMTEC76). Designed for read-write FLASH memory of ECUS via diagnostic connector. ..

Valeo V4X J2534, J2534 Sagem S3K

In stock

The Valeo V4X module is designed to read and write the FLASH memory of the Valeo S3000/V40/V42 ECU installed on Renault cars through the diagnostic connector. The Sagem S3K module is designed to read and write calibrations and the program of the Sagem S3000 ECU (512k FLASH) installed on Renault cars through the diagnostic connector. ..

Visteon ESU-131/411/418 and Visteon ESU-312/412/415 (kit)

In stock

The modules are designed to read / write flash memory of ECU Visteon ESU-131/312/411/412/415/418 vehicle Ford Focus 2, C-Max, Kuga engines 1.8...2.0 l (2004...2010) and Ford Mondeo 4 S-Max, Galaxy with 2.0 engine...2.3 l (2004..2011 onwards) ..

For programming ECU VS-5.6, you must use a special adapter, the cost of the adapter is included in the cost of the module. Required shipping of the adapter to the user. The vehicles are equipped with ECU ITELMA VS-5.6. ..

In stock

VS-5.6

$36.51

In stock

WestPort WP580 GAZ (J2534)

The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector. Work with the J2534 adapter, sold separately. ..