Ford Fiesta: 1.0L Ecoboost GTDI 100/125PS [C1BA] (MED17) [RD/WR/CK]
Ford Focus 3 2015: 1.0L Ecoboost 2015+ GTDI 100/125PS [DA6A] (MED17) [RD/WR/CK]
Ford Focus 3 2015: 1.5L Ecoboost 2015+ GTDI 150/180PS [FV6A] (EMS2510/EMS2511) [RD/WR/CK]
Ford Kuga 2 2017: 1.5L Ecoboost 2015+..
$93.03
Ford Focus 3: 1.0 L Ecoboost 2015+ GTDI 100/125PS [FV6A] (MEDG17) [RD/WR/CK]
Ford Kuga 2: 1.6 L Ecoboost GTDI AWD 150/182PS (MEDG17) [RD/WR/CK]
Ford Mondeo 5: 1.5 L Ecoboost GTDI AT 150/180PS (MEDG17) [RD/WR/CK]
Ford Mondeo 5: 2.0 L Ecoboost GTDI 200PS (MEDG17) [RD/WR/CK]
..
$93.03
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
$359.60
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
$359.60
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
The China EDC17CV44 Truck module allows you to view, compare and edit firmware files of FAV cars, Shacman trucks, MAZ, Yutong, etc. with a WP7, KR10, WP12 engine with an EDC17CV44 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection pha..
$332.24
Machine 2004-2012 years with modules PCM150F, PCM170F (two versions), M799G - Escape, Explorer, Mustang, Mazda CX9, etc
Requires adapter enabled FEPS, for example: Scanmatik-2 PRO, MongooseJLR, Mongoose, Ford, Openport 2.0, Ford/Mazda VCM 1, VCM 2
Mazda6 3.0 L AJ 2003-2005 [RD/WR/CK]
..
$93.03
The module is designed to work with ECU EDC17 installed with a diesel engine 6.7 l in the Ford. Supported read, write, review, and correction of the COP.
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [BC3A] [RD/WR/CK]
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [DC3A/FC3A] [RD/WR/CK..
$132.89
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
The module allows you to view, edit, compare the firmware files of Foton, JAC cars with Cummins engine with the Continental CM2880 control unit.
It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader.
The module contains more than 1000 b..
$332.24
The module is designed to work with DCM6.2AP, DCM7.1AP ECUs installed on Chinese-made cars via a diagnostic connector. Supports reading, writing, checking and correcting checksums.
Changan 2.0L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng 2.3L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng/Yucha..
$132.89
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
This module allows chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with the Abit M240 ECU.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the control program a..
$332.24
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.79
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.59
The module is designed for Chip tuning TCM (TCU) module automatic transmission has the internal name of the Power Stroke and mounted on the following models Ford F450, F350, F250, Explorer, Edge, Territory, and other
List of cars:
Car Ford MY11 E265 ASSY PART AR79-14C337-AC 201..
$93.03
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports the read/write and the conversion stock firmware with base IDS (VBF) in binary form.
..
$66.45
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
Working with this type of ECU is 'on the bench'.
Car Volvo S60 Y283 I5T_13A200_257_Y283_2.5L_US_AWD 31411200AA 2010 Denso SH72543 31312651AB Bench 69
Car Volvo XC60 Y413 Y413_A_MP_150hp_Eu6b 31669250AB 150 2010 Denso SH72546 31452623 Bench 69
Car Volvo V40 Y555 Y555_M_LP_150hp_Eu6b ..
$132.89
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
Read/Write firmware
Read/Delete errors
Check/Fix the checksum
The module automatically determines the size. Supports all markets. Read a full Hour, recording 10-15 minutes of cars and trucks. Machinery is the ECU is written HOUR SH7059 processor.
Used processors SH7058, ..
$106.32
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
