Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
For chip-tuning of cars of Chinese production with electronic gas pedal.
..
$119.61
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
The module is designed for chip tuning of VAG group cars with gasoline engines, Bosch MG1CS001 ECU, for example:
Audi A1 2.0 TFSI
Audi A3 2.0 TFSI
Audi A4 2.0 TFSI
Audi A5 2.0 TFSI
Audi A7 2.0 TFSI
Audi Q2 2.0 TFSI
Audi Q3 2.0 TFSI
Audi Q5 2.0 TFS..
$186.05
The module allows you to write firmware diagnostic method, without removing the ECU from the vehicle through the DLC (to work with the ECU on the car must be connected directly to the connector of the UNIT to disassemble the unit is not required).
Support ECU Bosch MSE3.0, M7.9.7, ME7.9.7, M7..
$66.45
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$212.63
The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recording.
..
$199.34
The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recordin..
$265.79
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$66.45
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$132.89
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$66.45
The modules are designed to read / write the FLASH/EEPROM of the ECU series Bosch EDC7/EDC16/PSG16/ME9 without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
The module does not s..
$199.34
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector.
Is free app for all users 2 or 3 version of module BSL TC17xx J2534.
Module Bosch MEDC17 Hyundai/Kia supported the following types of EC..
$106.32
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$39.87
Kia, Hyundai, equipped with ECU Bosch M(G)7.9.8. Designed for recording FLASH memory ECU Bosch M7.9.8 and MG7.9.8 via the diagnostic connector without removing the ECU from the vehicle.
..
$93.03
The modules are designed to read / write FLASH Chevrolet/Opel/Cadillac/SAAB, equipped with ECU Bosch ME9.x and the Bosch ME7.9.9 via the diagnostic connector.
Work with the J2534 adapter, sold separately. Module is a Bosch ME9.x GM makes automatic recalculation of the COP recorded calibration..
$53.16
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles.
..
$106.32
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$106.32
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector.
Table of applicability ECU SIMTEC 70:
Opel Astra G (1998-2000) X18XE1/X20XEV
Opel Vectra B (1998-2001) X18XE1/X20XEV
Opel Zafira (..
$119.61
License 49, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
..
$132.89
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
The Bosch EDC7UC31 MAZ / KRAZ / URAL module is designed for chip tuning of MAZ, KrAZ, MZKT, Ural cars and generator sets with diesel engines.
Supported firmware (software versions P766.120), module EDC7UC31 MAZ / KRAZ / URAL:
P766_120_MAZ_YAMZ-650_C_14_w_o_Cr_Ct
..
$265.79
The Bosch MD1CS001 (DDE802L, DDE803S) BMW module is designed for chip tuning of BMW cars with B47D20xx diesel engines. Installed on:
3rd G20 Series
5th series G30 and G31
X3 Series G01
X4 Series G02
Pay attention:
A third-party developer module! Tech..
$332.24
The Bosch EDC7UC31 KAMAZ module is designed for chip tuning of KAMAZ vehicles with diesel engines of the KAMAZ-740 family.
Supported firmware (software versions P702.141, P986.310), EDC7UC31 KAMAZ module:
702V141_740.60-360-290812_5460-4010142-01
702V141_740.60-360-29..
$265.79
Bosch EDC17C74 module is designed for chip tuning of Audi A3 / Q2, VW Golf / Passat / Tiguan, Skoda Superb / Kodiaq and others with 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
By default, the firmwar..
$132.89
Bosch EDC17C64 module is designed for chip tuning of Audi A3 / A4 / A6 / Q5, VW Golf7 / Sharan / Tiguan, Skoda Octavia and others with 1.6L and 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
..
$132.89
The Bosch EDC17C64 GAZ module is designed for chip tuning of GAZ group cars with VAG 2.0TDi diesel engines.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
The firmware of the Bosch EDC17 family controllers ..
$106.32
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
The module is designed for chip-tuning of automobiles in China, equipped with Bosch ME17.8.8, for example, Chery Tiggo 2.0 L, Chery Bonus (A19), Lifan X60, Lifan Solano II, etc.
Please note:
Third-party module developer! Technical support from the author of the module (KHN0..
$132.89
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5, for example, VW Tiguan 2.0 L TSI, VW Passat B6 1.8 L, Skoda Oktavia 1.8 L TSI, Audi A4 1.8 L TFSI, Seat Altea, Skoda Yeti 1.8 L TSI, etc..
Please note:
Third-party module developer! Technical suppo..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.5, for example, VW Touran 1.4 TFSI, VW Golf IV 1.4 TSI, VW Tiguan 1.4 TSI, Skoda Superb 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.21, for example, the VW Golf 1.4 TSI, Skoda Octavia 1.2 TSI, Audi A3 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch М..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.25, for example, the VW Golf 1.2 TSI, 1.4 TFSI, Skoda Octavia, Skoda Superb 1.4 TFSI, VW Jetta 1.4 TFSI.
Please note:
Third-party module developer! Technical support from the author of the module (K..
$159.47
The module is designed for chip-tuning of automobiles in China, equipped with Bosch MED17.8.10, for example, Geely Atlas 1.8 T.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored ..
$159.47
Optional module for chip tuning of BMW cars with Bosch MEVD17 control units.2.4
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Contain..
$132.89
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.9 control units.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family controllers is saved in the SMS-Soft Containe..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.2, for example, VW Passat 1.8 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the f..
$159.47
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
The module is designed for chip-tuning VAG cars equipped with Bosch ME17.5.26, for example, Skoda Octavia 1.6 MPI, Skoda Rapid 1.6 MPI Skoda Yeti 1.6, 1.6 MPI VW Jetta, VW Polo 1.6.
Please note:
Third-party module developer! Technical support from the author of the module (..
$159.47
The Bosch MD1CP002 (DE 832) BMW module is designed for chip tuning of BMW cars with B57D30xx and B47D20xx diesel engines.
Installed on:
3rd G20 Series
5th series G30 and G31
6th Series G32
7th series G11 and G12
8th series G14, G15 and G16
X3 S..
$332.24
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$93.03
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.5
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Container File format..
$132.89
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
The module is designed for chip-tuning VAG cars with engines 1.8 T, 2.0 T, equipped with Bosch MED17.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Sof..
$159.47
Additional module for chip tuning BMW cars with Bosch MEVD17.2.5 control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load such firmware, on..
$132.89
The module is designed for chip-tuning VAG group (VW Tiguan, Touareg) with a diesel engine capacity of 3.0 L, Bosch ECU EDC17CP14.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are st..
$132.89
Additional module for chip tuning BMW cars with Bosch MEVD17.2.8 and MEVD17.2.H control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load su..
$132.89
The module is designed for chip-tuning VAG group (VW Amarok, VW Crafter, VW LT) with a diesel engine capacity of 2.0 L, ECU Bosch EDC17C54.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC..
$132.89
Additional module for chip tuning Peugeot with the control units Bosch MEVD17.4.2.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Containe..
$132.89
The module is designed for chip-tuning of cars of the VAG group (Audi A3/A4/A5/A6/Q3/Q5/TT, Skoda Superb, VW Golf, VW Passat, VW Tiguan, etc.) with a diesel engine capacity of 2.0 L, EDC17C46 Bosch ECU.
Please note:
Third-party module developer! Technical support from the a..
$132.89
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
The module is designed for chip-tuning VAG group diesel engine 3.0 L ECU Bosch EDC17CP44.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are stored by default in the format of SMS-Soft..
$132.89
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
The module is designed for chip tuning Hyundai(IX35, IX55, Santa Fe, Tucson) and Kia(Carnival, Mohave, Sorento, Sportage) with diesel engines 2.0 CRDi (D4HA, 184HP), 2.2 CRDi (D4HB, 197HP) and 3.0 V6 CRDi (D6EB, 247HP).
Please note:
Third-party module developer! Technical s..
$106.32
The module is designed for chip tuning of BMW cars with the N55B30 engine.
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by d..
$132.89
The module is designed for chip-tuning, car Hyundai I40, Hyundai IX35, KIA Soul diesel engines 1.6 CRDi and 1.7 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmware families Bosch МEDC17 are stored by..
$106.32
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
The module is designed for chip tuning Hyundai(I30, I40, IX35, Santa Fe) and Kia(CEE'd, Optima, Soul, Sportage, Venga) with diesel engines 1.6 CRDi, 2.0 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Fir..
$106.32
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.89
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.32
For chip-tuning of automobiles in China, equipped with ECU Bosch M7.8.
..
$66.45
For chip tuning Hyundai and Kia with the control units Bosch ME17.9.11/12/13
..
$132.89
The Bosch EDC7UC31 GAZ module is designed for chip tuning of GAZ and MAZ cars with YAMZ-5344.20, YAMZ-53416, YAMZ-53441.20, YAMZ-53442, YAMZ-536, YAMZ-53601, YAMZ-53602, YAMZ-53603, YAMZ-53613, YAMZ-53622, YAMZ-53623, YAMZ-53624, MMZ-245 diesel engines.7.
Supported firmware (softwa..
$265.79
For chip tuning Hyundai vehicles equipped with KEFICO ECU or Bosch 7.9.7.
..
$66.45
For chip-tuning KIA vehicles equipped with KEFICO ECU or Bosch 7.9.7.
..
$66.45
For chip-tuning of automobiles in China, equipped with ECU Bosch M7.9.7 and M7.9.7+.
..
$66.45
The module is designed for chip tuning of Audi A4, A5, VW Amarok, Crafter, Passat, Transporter cars with 2.0L TDI and 2.5L TDI diesel engines.
Allows for professional chip tuning of Bosch EDC17CP20 control systems. The possibility of correctly disabling the ecology of EGR, DPF, SCR (AdBlue).
..
$199.34
The module is designed for chip tuning Hyundai Santa Fe, Hyundai Tucson, KIA Carnival, KIA Sorento Prime, KIA Sportage diesel engines 2.0 CRDi and 2.2 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmw..
$106.32
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
For chip tuning Hyundai and Kia with diesel engine (CRDI).
..
$106.32
For chip tuning cars Chevrolet Captiva and Opel Antara with the engine volume of 3.2 L.
..
$93.03
The module is designed for chip tuning of VAG cars (Skoda, Audi) with 1.0TFSI and 1.4TFSI engines equipped with Bosch MED17.1.27. Please note: Third-party developer module! Technical support from the module author (KHN09). Firmware for Bosch ME17 controllers is saved by default in SMS-Soft Contai..
$159.47
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalculated checksum of the se..
$39.87
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalculated checksum of the se..
$39.87
For chip-tuning Chevrolet Captiva cars with engines 2.4 L.
..
$106.32
For chip-tuning cars Opel turbocharged a series of engine Z20LEL, Z20LEH, Z20LER.
..
$93.03
For chip-tuning of cars Chery (QQ, Fora, B11, Acteco, Elara, Jagga, Eastar).
..
$66.45
For chip-tuning Opel cars with engines Z10XEP, Z12XEP, Z14XEP.
..
$93.03
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to work in service mode (on the table) with Bosch transmission control units with SH725xx family microcontrollers used in ZF 8HP, VAG DQ380/381/500, MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. It supports reading, writing, checking and correcting CS in FLASH memory and rea..
$132.89
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
The Bosch EDC17C76 (DDE742) module is designed for chip tuning of BMW cars with N 57 x diesel engines. Installed on:
X5 Series F15
X6 Series F16
Pay attention:
A third-party developer module! Technical support from the author of the module (M. Glazyrin).
&nb..
$265.79
The Bosch EDC17CP09 module (P_573 DDE73), (P_574 DDE73a), (P_613 DDE73) is designed for chip tuning of BMW cars with N57xx diesel engines. Installed on:
3rd series E90, E91, E92 and E93
5th Series F07
7th series F01 and F02
X5 E70 Series
X6 Series E71
Pay att..
$199.34
The Bosch EDC17CP45/CP 49 module (DE 731 P_730), (DDE731a P_731), (DDE731a P_731), (DDE751a P_1319) is designed for chip tuning of BMW cars with N47xx, N57xx, and B47xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, and F23
3rd series F3..
$332.24
The Bosch EDC17C50 (DE 701) BMW module is designed for chip tuning of BMW and MINI cars with N47x, B47xx and B37xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, F23, F45 and F46
3rd series E90, E91, F30, F31, and F34
4th series F32, ..
$332.24
The Bosch MD1CP032 (DE 853) BMW module is designed for chip tuning of BMW cars with M47 and B57xx diesel engines.
Installed on:
X5 Series G05
X6 Series G06
X7 Series G07
Pay attention:
A third-party developer module! Technical support from t..
$332.24
The module is designed for chip tuning of Citroen and Peugeot cars with 5GY (EP6FDTM), 5GZ (EP6FDT) engines equipped with Bosch MED17.4.4, for example, Peugeot 208 A9, Peugeot 308 T9, Peugeot 3008 T8, Citroen DS3 A55, Citroen DS5 B81, Citroen C4 Grand Picasso B78.
Pay attention:
..
$159.47
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$239.21
The module is designed to work with the Bosch MD1/M1 ECU "on the bench" using SPC5777M/SPC58/TC275TP/TC277TP/TC298TP/TC299TP microcontrollers. It supports reading, writing, checking and correcting checksums for FLASH, as well as reading and writing EEPROM. Work is possible only with an ECU with a..
$265.79
The module is designed to work with ECU Bosch ME7.9.20 installed on the Nissan X-Trail T31 petrol engine volume of 2.5 L. is Supported by the record validation and correction checksums.
EFI ME7.9.20 Calibration (ST10F275 Bosch EXT/512KB) [WR/CK]
..
$66.45
The module is designed to work in service mode with the ECU ME9/MED9/EDC16. It supports reading and writing the built-in flash memory of the MPC556/MPC562/MPC564 microcontrollers, external flash memory and EEPROM, as well as checking and correcting CS and RSA signatures (except for the MED9 VAG E..
$239.21
The module is designed to work with Bosch ECU installed in the Honda cars. Supported ECU MED17.9.3, EDC17C58 (write after unlocking in BSL) as well as EDC17CP06, EDC17CP16 (recording without unlocking).
PGM-FI (Bosch EDC17CP06/EDC17CP16/2MB) [WR/CK]
PGM-FI (Bosch EDC17CP50/4MB) [Unl..
$93.03
Sending activation files after 02/22/2022!
The module works with BCM manufactured by Bosch, Continental Gen.1(2 byte SeedKey), Gen.2(5 byte SeedKey).
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Readin..
$106.32
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.32
Module 'Module Bosch M78/ME797+ - OBD2' is designed to record via OBD2 connector firmware ECU Bosch M78, ME797+ cars Ukrainian and Chinese production. Currently supported ECU M78 cars ZAZ Forza, Geely CK2, Geely MK2, Geely Emgrand Great Wall Wingle, ECU M788 car JAC, Geely GC6, Chery Tiggo, Lifan..
$46.90
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
Module Bosch ME17.9.11/12/13/21 - OBD2' is designed to read and write via OBD2 connector tuning and serial firmware. This module provides a fake digital signature of the downloaded firmware to enable it write via OBD2 connector.
..
$91.02
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.80
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.74
The Bosch module M(E)7.9.7-OBDII (Bosch Kefico M7.9.7, Bosch M7.9.7(+) (VAZ), Bosch M7.9.7+ (Geely cars, Amulet), Bosch M7.9.7.1 (Chevrolet Aveo), Bosch ME7.9.7 (Chery cars))
..
$11.71
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.80
The module is designed to work through the diagnostic connector of a car with DSG and automatic transmission units used in VAG concern cars. It supports reading (virtual), writing, checking and correcting checksums.
DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL420/AL600 (09L/09E) K-Line..
$132.89
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.47
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.45
Module Bosch ME17.9.11/12-OBD2 is designed to write FLASH memory of ECU Bosch ME17.9.11, Bosch ME17.9.12 via the J2534 device. Please note that this module can record only serial firmware!
..
$11.71
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.61
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.58
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.74
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.60
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$53.16
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$53.16
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
The module is designed to record the FLASH memory of the ECU M 7.9.8 7.9.8 and MG via OBDII diagnostic connector.
..
$70.31
Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any e..
$86.38
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$106.32
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$106.32
Includes maps calibrations for all versions (free map updates for new software). Works with standard (uncompressed) format. Writing a modified firmware available only via BSL mode any existing boot loader.
..
$93.03
The module is designed to read and write FLASH memory from ECU ME7.9.9 Chevrolet Captiva via OBDII diagnostic connector.
..
$58.61
The module is intended for editing data from Ieprom blocks Bosch ABS9, VAZ cars (XRAY / VESTA). You can change the main mileage, mileage after ECU reset, TPMS log mileage, VIN, Hardware ID, wheel diameter, TPMS activation flag. The module monitors the integrity of the data upon opening and recalc..
$26.58
FID: 180, 181
Module to read and write via the diagnostic connector Ford control units Bosch MG1.
Ford Bosch MG1CS015 TC277 (FID: 180)
The family support units Ford Bosch MG1CS015 processor-based Infineon Aurix TC277 with internal memory of 4 MB.
Allows readi..
$239.73
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.73
Includes extra features: preparing firmware ME17.9.11/12/13 to record its diagnostic method (WITHOUT opening the UNIT) disable diagnostic read firmware ME17.9.11/12/13 ( just 17.9.7, 17.9.71, 17.9.8, 17.9.21). Advanced features available for purchase under any of the modules of the family Bosch M..
$26.58
The module is intended for editing of data logger units UAZ Bosch M(E)17.9.7 and M(E)17.9.71. So the module allows to change the counter programmed the ECU. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes,..
$26.58
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.66
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
$299.66
The module is intended for editing of data logger units VAZ Bosch ME17.9.7 and ME17.9.71. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes, respectively the type of ECU).
..
$26.58
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
Module to work through the diagnostic connector for Ethernet control units Bosch MG1 and MD1 mounted on the BMW F and G-series.
Supported units Bosch processor-based NXP MPC5777 with 7.5 Mb of internal flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)
BMW Fx..
$419.53
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.53
The module is designed for chip tuning of VAG cars equipped with Bosch MED17.5.20 with 1.4 TFSI engines.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in..
$159.47
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.96
Support cars: Hyundai Accent, Elantra, Kia Rio, Cerato, Ceed
..
$52.71
The module for the new version of the program Chiploader NG
Module [51] Bosch MEDC17 - Bench is designed to read and write the internal memory (flash and eeprom) of the processor is Tricore ECU Bosch MEDC17 on the table without disassembling the ECU.
Detailed information ..
$258.00
Support vehicles: Chevrolet Captiva
..
$29.35
Only supports record turbocharged petrol auto. Ford.
..
$39.87
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.89
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports the read/write and the conversion stock firmware with base IDS (VBF) in binary form.
..
$66.45
Features of the module:
Write firmware
Read/Delete errors
Virtual reading
Check/Fix the checksum (the bypass digital signature)
Tabs:
CAN - for Master ECU
Slave To record a second engine ECU (Slave)
Stock - to return to the flow without using th..
$132.89
Module functions:
Recording calibrations
Identification
Reading/erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
DDE721b
DDE73a
DDE731a
MEVD17.2
..
$132.89
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.89
The module is designed for chip tuning of Korean-made cars of 2018 and newer with GDI gasoline engines equipped with Kefico CPEGD2.20.1 / CPEGD2.20.2 / CPEGD2.20.3 / CPGDSH2.26.1 / CPGDSH2.26.3 / CPGPSH2.14 ECUs.1.
These ECUs are used on cars such as:
Hyundai Elantra, Avant..
$265.79
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.89
The module is designed to work with the Bosch ECU automatic transmission 6HP, 8HP a / m JLR through the diagnostic connector of cars. Supported read, write, check checksum correction:
ZF 6HP26/6HP28 TCM (MPC5xx/TC1766) [RD/WR/CK]
ZF 6HP28 Continental TCM (TC1766) [AH42-Ax] [R..
$119.61
The module is designed to work with ECU Bosch ME(D)17/EDC17 working on CAN Protocol TP2.0/K-Line. Supports recording via the diagnostic connector modified firmware, validation and correction checksums. Supported ECU MED17.1/17.1.1, ME(D)17.5/17.5.1/17.5.2/17.5.5/17.5.6/17.5.20, EDC17U01/U05, EDC1..
$119.61
The module is designed to work with ECU Bosch EDC17CP27/EDC17C49/EDC17C79 installed on vehicles of Jeep. Supported read, write, review, and correction checksums.
2.8 L CRDI (EDC17CP27)[RD/WR/CK]
3.0 L CRDI (EDC17C49/C79) [RD/WR/CK] read-may require direct connection to the ECU
..
$93.03
VW Touran, Golf, Passat, Transporter, Caddy cars with engines AVQ,BKC,BMT,BLS, etc. with a volume of 1.9L
Supported Software:
1037367485P379U6FP
1037368205P213U6FT
1037370254P213U8C3
1037370811379U85B6
1037371094379U85B6
1037371250379U85B6
..
$39.87
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
Module Bosch ME17.9.7(1)-OBD2 with write support ECU Bosch ME17.9.7 via the OBD2 socket of the car VAZ, UAZ, as well as records with ECU Bosch ME17.9.71 UAZ.
Please note that for correct record ECU Bosch M(E)17.9.71 you must first disable the monitoring of a digital signature, and writing the..
$58.61
The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector.
ECU Continental EMS3155 ustanavlivaetsya on engines 1.2 T.
ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L.
ECU Bosch EDC17C84 i..
$132.89
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by default. To download such firmware, you need to use only the CombiLoader loader.
Savi..
$106.32
Distribution of activation files after 01.06.2023
License 118, may be applicable at the discretion of the licensee (user) to work:
with a Bosch electric power steering on the Nec V850 70F3187 + EEPROM 95080 MK on the table or via the OBDII connector (where there is a technical ..
$66.45
The module is designed to work with ECU Bosch MED17.7.1/MED17.7.2/MED17.7.5/MED17.7.3/MED17.7.3.1, EDC17CP01/EDC17CP10 (with external flash), EDC17CP46/EDC17CP57/EDC17CP60/EDC17C66 installed on vehicles from Mercedes-Benz and Infiniti some. Supported reading (only for blocks EDC17), entry, valida..
$159.47
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
The set of modules (General license):
EDC17C11 Renault Bosch J2534
EDC17C42 Renault Bosch J2534
SID301 Renault J2534
SID305/306 Renault J2534
SID307 Renault J2534
Delphi DCM3.4 Renault J2534
The modules are designed to read/write and(or) field calibrati..
$106.32
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.74
License 37, may be applicable at the discretion of the licensee (user) to the work:
PIN reading
Reading ID keys
Reading the number of keys
List of supported ECUs:
BOSCH 17.9.11(Hyundai/Kia)
BOSCH 17.9.12(Hyundai/Kia)
..
$79.74
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
This module enables the following additional functions:
Mixing of the calibration firmware Bosch ME17.9.7 VAZ and UAZ. The function requires the module ME17.9.7 VAZ/UAZ.
Patch to disallow read firmware Bosch ME17.9.7, Bosch ME17.9.71 (VAZ, UAZ), Bosch ME17.9.11/12 and ME17.9.21 (Kia..
$39.87
Basic kit:
GM ISFI-2S
VAZ, the first serial electronic control system on domestic cars.
January 4
VAZ, second serial electronic system of injection control, the domestic counterpart of ISFI-2S. Used since 1995
January-5.1.x
VAZ, a domestic ..
$66.45
License 31, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
It only works with the full firmware version (FULL FLASH..
$106.32
A special adapter to connect the control units on the table.
Performs automatic power management, and boot pins through the J2534 adapter.*
Required to read in the BSL mode for control units Bosch M7.8/ME7.8.8 and Continental SIM2K-25x/26x
* - tested and guaranteed works wi..
$53.16
Machine 2004-2012 years with modules PCM150F, PCM170F (two versions), M799G - Escape, Explorer, Mustang, Mazda CX9, etc
Requires adapter enabled FEPS, for example: Scanmatik-2 PRO, MongooseJLR, Mongoose, Ford, Openport 2.0, Ford/Mazda VCM 1, VCM 2
Mazda6 3.0 L AJ 2003-2005 [RD/WR/CK]
..
$93.03
Designed for chip-tuning of cars and cars of Chinese production installed ECU BOSCH M7.8. Supports recording FLASH via the diagnostic connector. As well as reading and writing FLASH/EEPROM memory controller via BSL mode.
..
$66.45
Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering.
..
$3 236.37
License 26, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash or EEPROM file, depending on the type of ECU.
Works as an edit..
$106.32
Designed for chip-tuning of cars VAZ, UAZ with mounted ECU BOSCH ME17.9.7. Supports only FLASH programming through the diagnostic connector
..
$106.32
Module OPEL ECU - OBD2 includes work with the ECU Simtec-71.5, Simtec-71.6, Simtec-75.1, 75.5 Simtec, Simtec 81.1, Delphi MT35E, Bosch ME9.1 / ACDelco E77 (read and write FLASH memory). Supports data only ECU on the CAN bus.
..
$56.62
The module is designed to work with ECU Bosch EDC17CV44/54
..
$66.45
The kit includes the modules:
28 Module Ford EMS2204;
27 Module-Ford Bosch MED17.2;
22 Module, Ford, Siemens VDO EMS2102 and EMS2101;
21 Module Ford Diesel SID206;
19 Module Ford SIM210, SIM22;
15 Module-Ford Bosch ME 9.0 Petrol (Turbo);
14 Module Ford Diesel Delphi DC..
$265.79
The Ford EDC17CV41 module 24 allows you to view, compare and edit firmware files of Ford Cargo F-Max vehicles (Bosch EDC17CV41 ECU).
Calibrations are available for editing: boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phases, torque limits, ..
$398.68
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.66
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
The KMS MD1CE100 module allows you to view, compare and edit the firmware files of Kamaz K5 cars with an R6 engine (Bosch MD1CE100 ECU).
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, DPF, EGR, AdBlue, ..
$664.47
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)
Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Mar..
$239.73
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.73
Set of 3 modules at a discount.
BMW Bosch Exx CAN
Fxx Bosch ENET
Fxx/Gxx Bosch MG1/MD1 ENET
..
$1 078.79
Designed for chip-tuning of cars Hyundai, KIA, CHERY, GEELY, HAFEI, VORTEX ESTINA c installed ECU BOSCH M7.9.7,M7.9.7+,МЕ7.9.7, M(G)7.9.8
..
$66.45
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.74
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
Designed for chip-tuning of cars VAZ, GAZ, UAZ, ZAZ installed the ECU Я7.2+, M11/М11ЕТ/М11CR/M73/M10.3/M11.4/ Bosch M7.9.7 and M7.9.7+
..
$66.45
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.89
Module TC1762/TC1766/TC1796/TC1797/TC1767/TC1724/TC1738/TC1791/TC1793/TC1798/TC1728/TC1782/TC1784/GPT boot mode (ECU families Bosch ME17.9.x and other CPU Tricore TC1762 / TC1766 / TC1796 / TC1797 / TC1767 / TC1724 / TC1738 / TC1791 / TC1793 / TC1798 / TC1728 / TC1782 / TC1784)
Clo..
$180.15
Module EDC17/MED(G)17 (Kia/Hyundai) - OBD2 is designed to write FLASH memory of ECU Bosch EDC17C08, Bosch, EDC17CP14, Bosch MED(G)17.9.8 via the J2534 device.
Please note that this module can only record the previously prepared serial tuning or firmware!
..
$28.33
Включает карты основных калибровок прошивок M7.8.0. Бесплатное обновление карт для новых софтов Bosch M7.8.0. Работает с стандартным форматом прошивок.
Возможности двухрежимных прошивок Bosch M7.8.0: Переключение основных калибровок (более 20). Организация переключения режимов по сигналам ДТВ..
$51.83
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.87
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.73
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
The module is designed to work with ECU Bosch EDC7UC31/MS6.1
..
$66.45
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.36
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.59
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.22
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.87
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.34
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.89
It is designed for reading and writing software/calibrations of the SID605/WISE13H/WISE15/MD1/EQ EDC17 V6/V7 ECU installed on MAZ cars and Chinese-made cars via a diagnostic connector.
The kit supports the following types of ECU:
SID605: software/calibration recording.
..
$265.79
![[54] BOSCH ME17.8.8 - OBD2](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[54] BOSCH ME17.8.8 - OBD2")
