The module is designed to work with the Mitsubishi ECU of cars of various brands on the "table". Supports read, write, review, and correction checksums:
CAN-bus Bootloader FLASH (MH8114F/MH8115F/MH8501F) [RD/WR/CK]
CAN-bus Bootloader FLASH (MH8601F/MH8610F/MH8611F/1N83M) [RD/WR/CK]
..
$119.46
Work with ECU Hitachi processor SH72533 installed on modern vehicles X-Trail, Qashqai, Juke, Teana, Murano, Patrol, Pathfinder and others with the 2014-2016 model years. The type definition module, read and write calibration check/correction checksums.
EFI SH72533 Gen 2 (2014+) Calibratio..
$66.36
MH Generic Read-Only [RD]
Colt MT (MH8304F/512KB) [RD/WR/CK]
Colt AT (MH8304F/768KB) [RD/WR/CK]
Colt RallyArt 1.5T (MH8104F/512KB) [RD/WR/CK]
Galant 9 2.4L (2005-) (MH8304F/768KB) [RD/WR/CK]
Pajero MT (2007-) (MH8302F/512KB) [RD/WR/CK]
Pajero AT (2007-) (MH..
$119.46
EFI Generic Read-Only (Hitachi) [RD]
EFI SH705519N (Hitachi SH7055/512KB) [RD/WR/CK]
EFI SH705822N, SH705828N (Hitachi SH7058/1MB) [RD/WR/CK]
EFI SH705927N (Hitachi SH7059/1.5 MB) [RD/WR/CK]
EFI SH725331N (Hitachi SH72531/1.25 MB) [RD/WR/CK]
EFI S7253332N (Hitach..
$106.18
The module is designed to work with the ECU EDC7/EDC16/EDC17 diesel engines Mitsubishi Fuso Canter. Supported read, write, review, and correction of the COP. For some cars with ECU EDC7/EDC16 for writing may require a direct connection to the connector block.
Fuso Canter (EDC7C4-6/EDC16C3..
$132.73
The module is designed to work with blocks of variable-speed drives and automatic transmission that are installed on Mitsubishi vehicles, supported by reading and writing.
CVT Lancer X/ASX 1.8/2.0L, Outlander XL/3 2.0/2.4L (MH8104F/512KB MH8106F/1MB) [RD/WR/CK]
AT Pajero Sport (2010..
$132.73
Work with ECU Denso processors SH7058, SH7058S and SH7059 installed on vehicles Mitsubishi. Automatic detection of module type, read, write, verification/correction checksums.
Denso Diesel (SH7058/SH7058S/1MB SH7059/1.5MB SH72543/2MB) [RD/WR/CK]
..
$92.91
PGM-FI Generic Read-Only [RD]
AT/CVT/DCT Generic Read-Only [RD]
PGM-FI (Keihin SH7058/1MB) [RD/WR/CK]
PGM-FI (Keihin SH72543/2MB) [RD/WR/CK]
PGM-FI (Keihin SH72546/3.75MB) [RD/WR/CK]
PGM-FI (Keihin MPC5566/3MB) [RD/WR/CK]
PGM-FI (Keihin TC1782/..
$199.09
The module is designed to work with ECU Bosch ME(D)17/EDC17 working on CAN Protocol TP2.0/K-Line. Supports recording via the diagnostic connector modified firmware, validation and correction checksums. Supported ECU MED17.1/17.1.1, ME(D)17.5/17.5.1/17.5.2/17.5.5/17.5.6/17.5.20, EDC17U01/U05, EDC1..
$119.46
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.64
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.88
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055S/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7058/1MB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2007+ CAN-bus (SH7058S/1MB) [RD/..
$119.46
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.73
FIDs: 346, 347
A module for working on a CAN bus with control units of Peugeot and Citroen petrol cars.
PSA Valeo V46.11 (FID: 346)
The control unit is powered by a Renesas SH72544 processor with 2.5 Mb internal flash memory. Allows reading and writing of the..
$179.29
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.88
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
$359.82
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.64
FID: 340
Module for working with Honda/Acura cars via CAN bus with Keihin control units.
The family supports control units:
Keihin SH7058 (1MB)
Keihin SH72543 (2MB)
Keihin MPC5554 (2MB)
Keihin TC1782 (2.5MB)
Keihin TC275 (4MB)
Ke..
$309.13
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.36
The module is designed to work with engine control units, automatic transmission and hybrid installation of Toyota/Lexus/Scion/Hino vehicles via CAN bus and K-line. There is a virtual reading function for ECUs operating over the K-Line and CAN-bus protocol (if there is a corresponding file on the..
$132.73
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.85
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.94
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.79
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.92
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.73
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.92
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.85
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.88
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
$359.82
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.79
Almost all types of blocks that are programmed via the Can bus are supported:
Matsushita SH7058 1024K
Matsushita SH72543 2048K
Continental MPC5554 2048K
Temic MPC5554 2048K
Keihin MPC5566 3072K
Keihin SH72543 2048K
Keihin SH7058 1024K
Hitachi SH70..
$159.27
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.23
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.88
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
$299.85
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
$239.88
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.91
FID: 238, 242, 245, 246
Module for reading and writing control unit Denso installed on diesel vehicles with engines Mazda SkyActiv-D.
Mazda Diesel Denso Gen3 SH72543 (FID: 246)
The control unit is powered by a processor Renesas SH72543 with internal flash memory ..
$239.88
FID: 180, 181
Module to read and write via the diagnostic connector Ford control units Bosch MG1.
Ford Bosch MG1CS015 TC277 (FID: 180)
The family support units Ford Bosch MG1CS015 processor-based Infineon Aurix TC277 with internal memory of 4 MB.
Allows readi..
$239.88
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.79
FIDs: 155, 157, 177
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.
Renault Siemens SID301 (FID:157)
This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0..
$239.88
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
$239.88
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.30
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
$123.65
FIDs: 142, 143, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 349, 353
A module for working with gasoline, electric and diesel cars with Denso SH72xxx CAN control units.
The work is performed when connected to the table via the CAN bus. Removing the ECU is necessa..
$239.88
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
$299.85
License 13, may be applicable at the discretion of the licensee (user) to the work:
Reading/Clearing fault codes
Clearing collision information.
Unlocking the ECU.
Changing the ECU configuration.
Reading/VIN entry.
List of supported ECUs:
Renault SAND..
$79.64
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.88
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$66.36
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$33.18
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.86
Cable to connect your ECU 'on the table' and programming using Combiloader and related modules. Version CAN + GPT
..
$59.73
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.88
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$39.82
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.64
ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong.
Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle.
Works through the J2534 interface.
ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato..
$92.91
Kit modules:
Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector.
Isuzu Transtron ..
$106.18
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.36
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.64
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.64
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.82
Designed to work with Hitachi ECU (read full flash, write calibration, recalculation of the COP) with the SH705x CPUs installed on Nissan/Infiniti.
read Full cpu dump SH705x, SH7253x / Read Full Flash cpu SH705x, SH7253x
recalculation of the checksum / CRC
..
$159.27
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.85
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.73
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
$239.88
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$106.18
Great Wall/Lifan ME17 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.6L/2.0L D4G15/E4G16/SQR484 (ME17.8.8) [RD/WR/CK]
Chery 2.0L D4G20 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.5T/2.0T E4G15C/E4T15C/D4T20 (ME17U6) [RD/WR/CK]
Chery 1.6T F4J16 (MED17.8.10) [RD/WR..
$159.27
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.85
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.85
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation.
..
$79.64
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.18
Cable to overwrite the ECU M74 with Combiloader and ACC. module. The new version with the socket of OBD (CAN)
..
$53.09
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$92.91
Set of 3 modules at a discount.
BMW Bosch Exx CAN
Fxx Bosch ENET
Fxx/Gxx Bosch MG1/MD1 ENET
..
$1 079.47
The module is designed for operation with control units EDC15C7, EDC16CP34 and EDC16C39, supported reading and writing of calibration on K-line and the record as a whole on the CAN bus (supports basic BDM format and the format of GDS), verification and correction checksums.
2.0 L, 2.5 L C..
$66.36
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.64
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.18
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.73
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.76
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.36
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.73
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.27
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.73
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.36
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$743.28 $542.86
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
$359.82
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$26.55
The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector.
Table of applicability ECU SIMTEC 70:
Opel Astra G (1998-2000) X18XE1/X20XEV
Opel Vectra B (1998-2001) X18XE1/X20XEV
Opel Zafira (..
$119.46
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$79.64
License 136, may be applicable at the discretion of the licensee (user) to the work:
with direct connection via CAN bus with Magneti Marelli IAW 9 GVCE control units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data.
Magneti Marelli IAW 9GV..
$79.64
Module OPEL ECU - OBD2 includes work with the ECU Simtec-71.5, Simtec-71.6, Simtec-75.1, 75.5 Simtec, Simtec 81.1, Delphi MT35E, Bosch ME9.1 / ACDelco E77 (read and write FLASH memory). Supports data only ECU on the CAN bus.
..
$56.66
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.64
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
$239.88
Forester, Impreza, Legacy 2000-2002 K-Line (UJ WA12212920/128KB) (Test) [RD/WR/NC]
Forester, Impreza, Legacy 2000-2002 K-Line (UJ WA12212930/256KB) [RD/WR/NC]
Forester, Impreza, Legacy 2002-2005 K-Line (UJ/Hitachi WA12212940/384KB) (Test) [RD/WR/NC]
Forester, Impreza, Legacy..
$119.46
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.09
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.88
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
$299.85
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.85
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.64
FID: 280
Module for reading and writing by CANbus Isuzu diesel vehicles with Transtron ECUs based on Renesas SH7058, SH7059, SH72533 and SH72544.
Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)
Family for Transtron ECUs based on MCUs Renesas SH7058/SH7059/..
$179.91
The module is designed for operation with control units SIMK-41/43, SIM2K-47 used in vehicles Kia/Hyundai. Supported reading (when available), entry, checking and correction of the checksum, automatically detect the type of ECU.
2.0 L, 2.7 L K-Line (SIMK-41/43) [RD/WR/CK]
2.0 L, 2.4..
$66.36
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.73
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.64
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.91
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.73
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.18
The module is designed to work with ECU Delphi MT38, Delphi MT86, supported reading (where possible), recording, checking and correction checksums. MT38 available for work in BSL mode.
2.7L, 3.3L, 3.8L (MT38/CAN) [WR/CK]
2.7L, 3.3L (MT38/K-Line) [RD/WR/CK]
2.7L, 3.3..
$92.91
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$238.91
License 05, may be applicable at the discretion of the licensee (user) to the work:
Autoliv production units
INFINEON XC2361 Reading/EEPROM recording, Flash reading, Clearing collision information via CAN.
INFINEON XC2336B Reading/EEPROM recording, Flash reading, Clea..
$79.64
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
BitBox is an evolving software package that allows to identify, read and write the internal ..
$46.99
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.64
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.64
Reading(slow)/Entry of the calibration Can
Read/Delete errors
Check/Fix the checksum
Virtual reading
Supported units EDC17C08 and EDC17CP14 with any TPROT
..
$66.36
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.64
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.64
The module is designed to work through the diagnostic connector of a car with DSG and automatic transmission units used in VAG concern cars. It supports reading (virtual), writing, checking and correcting checksums.
DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL420/AL600 (09L/09E) K-Line..
$132.73
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.64
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.84
Read/Write calibration by K line
Record calibration + program Can
Read/Delete errors
Check/Fix the checksum (fake digital signatures)
Supported units EDC16C39-5.41 and EDC16CP34-5.30
..
$66.36
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.92
The module supports the TCM/M32R CVT [512 KB/896kb/1024kb] CAN
Identification
Read/Write calibration
Read/Delete errors
Recalculation of the COP
..
$92.91
Module features:
Reading calibrations
Recording calibrations
Reading the full data image
Recording a complete data image
Identification
Reading/erasing errors
Recalculation of the checksum
The module also supports:
..
$66.36
Features of the module:
Write firmware
Read/Delete errors
Virtual reading
Check/Fix the checksum (the bypass digital signature)
Tabs:
CAN - for Master ECU
Slave To record a second engine ECU (Slave)
Stock - to return to the flow without using th..
$132.73
The module is designed for diagnostics of EDC17CV44/54 CAN
..
$106.18
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.64
Designed for chip tuning of MAZ cars with installed WISE15 ECU (WEICHAI). To work with the WISE15 ECU, you need a 24V J2534 adapter and a CAN2CAN adapter.
..
$132.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.91
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.94
Cable for read and write ECU М86 with Combiloader and the module. In the cable combined essential variations pins CAN. Have a switch pin enable programming.
..
$53.09
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.64
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
$119.94
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.92
The kit includes the modules:
39 Module, Nissan/Infiniti Hitachi/Unisia Jecs SH705x, K-line
37 Module, Nissan/Infiniti Hitachi SH705x, SH7253x Can
..
$199.09
License 01, may be applicable at the discretion of the licensee (user) to the work:
Allows you to read and write the FULL Flash image 29F200/29F400.
Allows you to read/write the emulated in Flash EEPROM.
The "MAKE VIRGIN" function allows you to make the ECU "New", suitable ..
$132.73
Module 3 supports reading and writing of the following types of processors of the M32r series used in both the engine control unit and the active central differential control unit:
MH8104F_(512K) by CAN
MH8104F_(512k) by Kline (repair/restoration)
MH8106F_(1024K) by CAN
..
$92.91
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.73
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.12
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.40
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 193.23
CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary f..
$99.55
Designed for chip tuning of ECU Abit M20.20, M20.21, M240, M240S1, MD22. Modules allow you to: - Read and write calibration area - Read and write control program - Calculate and, if necessary, automatically correct the checksum of the calibration area - Perform ECU identification - Read and reset..
$132.73
License 32, may be applicable at the discretion of the licensee (user) to the work:
Chery Kimo Read/Write EEPROM, Read/Write KM (Adapter J2534)
Chery Amulet Read/Write EEPROM, Read/Write KM(KLine)
Chery Tiggo ver 1 Read/Write EEPROM, Read/Write KM(KLine)
Chery Fora Read/..
$66.36
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
$239.88
Module supported:
Read/erase error codes
Verification and recalculation of the checksum (CS)
Identification
Entry
Reading
For the following ECU's:
BRZ SH72531 [1280k] CAN 2013+
SH7058 [1024k] CAN 2007+
SH7058 [1024k] K-line 2003+
SH7..
$106.18
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.36
The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles.
Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available.
..
$199.09
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.88
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.91
The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles.
Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors.
..
$132.73
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.18
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.82
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.74
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.73
Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
$143.93
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.18
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.18
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.85
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.64
Autobile 'Volga', 'Gazelle', UAZ, equipped with ECU Mikas-Mikas 11b-11ET, Mikas-11CR or VS-8. Can be programmed without changes to the ECU. Does not work with 'closed' versions of the ECU!
..
$19.91
Chevrolet (Lacetti, Epica, Tacuma, Rezzo), Daewoo (Matiz). ECU programming can be performed directly on the vehicle through the diagnostic connector.
..
$92.91
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.46
The family of modules includes three separate module from the ECU to the M74.5, M75, MIKAS-12 or M86 (FOR ITELMA, firmware, VAZ and UAZ), which can be purchased independently. All the modules have identical functionality and are designed to create dual-mode firmware with an individual set of cali..
$53.09
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.46
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.09
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.64
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.09
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.09
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.09
The kit contains modules:
Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L.
Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particu..
$66.36
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.09
The BMW cars with ECU Siemens MS41/42/43: E36/E38/E39/E46/E53 6-cyl 2.0 L — 3.0 L. ECU Programming can be performed directly on the vehicle through the diagnostic connector.
..
$66.36
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.46
CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1.
Power supply.
To work CombiBox must submit the stabilized voltage..
$92.91
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.99
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$132.73
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$212.37
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$92.91
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.18
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.73
Cars equipped with ECU Mikas-11,ET(CR) and M73 with the latest version of the software. The module allows to work with the so-called 'closed ECU', which cannot work with standard modules Mikas-11/Mikas-11ET/Mikas-11CR/VS-8, January-7.2+/M73 or BSL.
..
$119.46
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$92.91
Universal adapter for SM2/SM2PRO + PCMflash Scanner with manual and automatic control of power supply to the unit and BOOT control.
Indication:
Green - Adapter power
Red - power on of the POWER+12v unit (manual switch-on is possible).
Blue - enabling BOOT, outpu..
$73.00
License 75, may be applicable at the discretion of the licensee (user) to the work:
Reading/FullFlash Entry
Reading/EEPROM recording
The ability not to overwrite the boot sector.
The module allows you to use your Seed Key, in case it was replaced with a non-s..
$106.18
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.18
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.73
The Bosch EDC7UC31 MAZ / KRAZ / URAL module is designed for chip tuning of MAZ, KrAZ, MZKT, Ural cars and generator sets with diesel engines.
Supported firmware (software versions P766.120), module EDC7UC31 MAZ / KRAZ / URAL:
P766_120_MAZ_YAMZ-650_C_14_w_o_Cr_Ct
..
$265.46
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.09
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.09
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.09
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.09
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
The cars ECU:
Logan / Sandero EMS3120 TC1738 [2048k] CAN
Fluence / Megane EMS3120 TC1738 [2048k] CAN
Fl..
$86.27
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.73
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.88
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
$239.88
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.88
Reading calibrations
A record of calibrations
The writing of a complete image data
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
MED17 only a virtual reading. When tuning record-only calibrations. Stoke can record and ..
$132.73
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.38
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$92.91
The module is designed to work in service mode with the ECU ME9/MED9/EDC16. It supports reading and writing the built-in flash memory of the MPC556/MPC562/MPC564 microcontrollers, external flash memory and EEPROM, as well as checking and correcting CS and RSA signatures (except for the MED9 VAG E..
$238.91
License 70, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Full Flash file, read in BSL mode or by a programmer.
Wor..
$106.18
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.88
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.88
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
$239.88
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.73
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.88
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$238.91
License 48, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
MB(CY)96F313
MB(CY)96F315
MB(CY)96F326
MB(CY)96F336
MB(CY)96F338
MB(CY)96F343
MB(CY)96F345
..
$106.18
A set of their 5 modules discount for Toyota cars.
The kit includes:
Denso Toyota Gen1 CAN
Toyota Denso Gen2/newGen CAN
Toyota Denso Gen3 CAN
Toyota Delphi Gen1 CAN
Toyota Gen1 Virtual Reader
..
$1 019.50
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Available to all users free Module Jan 7.2+ module 1.
Key features:
Edit the calibra..
$33.18
License 138, may be applicable at the discretion of the licensee (user) to work with:
ECU EGS gasoline engines installed on UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(full content)
FLASH recording (control program + calibration area or ..
$66.36
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.46
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.18
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.64
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.09
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days.
MMC Flasher universal Downloader intended for chip tuning Hyundai, Kia, Mitsubishi, Mazda, Nissan, Honda, Subaru..
$30.53
License 59, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
D70F3230 -D70F3231 -D70F3232 -D70F3233 -D70F3234 -D70F3235 -D70F3236 -D70F3237 -D70F3238 -D70F3239 -D70F3333 -D70F3334-D70F333..
$66.36
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
The module does NOT checksum when you save the firmware.
Supported firmware versions:
14CE5A_F4KH1DQGNV1-20161015-130049 — Nissan X-trail T32 2.0 144hp 2015 AT
14C..
$159.27
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
$299.85
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
$239.88
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.88
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.94
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.95
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
$239.88
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.94
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.71
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.88
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.64
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.38
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.38
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.73
The module is intended for editing data from Ieprom blocks Bosch ABS9, VAZ cars (XRAY / VESTA). You can change the main mileage, mileage after ECU reset, TPMS log mileage, VIN, Hardware ID, wheel diameter, TPMS activation flag. The module monitors the integrity of the data upon opening and recalc..
$26.55
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.36
License 132, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with the Continental VDO MQBAB dashboard based on the NEC35xx MK installed on cars: Audi,Skoda,Seat,VW, which allows for full-fledged repair and restoration work with ECU data.
..
$331.82
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.73
License 101 can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with multimedia units installed on GM cars, which allows for full-fledged repair and restoration work with ECU data.
Scope of application: Change of region, Us..
$331.82
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.88
What is this system?
If You have several branches or regular customers that You make the firmware and they are interested in our product – they can get all the modules that You have, but they will not have access to the firmware, and You will keep the secret of your development. Th..
$299.85
Module GM MT60/MT80 Extended - OBD2 is designed to read and write full dump of the internal FLASH and EEPROM memory of ECU MT60/MT80 manufactured by GM. The module can be used to cloning units.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lit..
$84.87
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.97
License 68, may be applicable at the discretion of the licensee (user) to the work:
1. Auto-search Mode:
Reading the mileage of HYUNDAI / KIA cars by OBDII with the MED17/EDC17 ECU.
Automatic search for the specified mileage in the EEPROM dump loaded into the program...
$106.18
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.25
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.18
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
MDflasher software for odometer adjusting, to work with the immobilizer, the Airbag, and als..
$39.82
A comprehensive package brands ScanDoc - complete package brands for ScanDoc ScanDoc scanners and Compact. The package also opens a brand under development.
The coverage map on marks you can see on the developer's website →.
The module opens with one click via the Internet. Re-download th..
$783.10
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.18
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.42
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.64
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.46
The module is designed to delete data collision (CRASH DATA):
Toyota DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Toyota FUJITSU SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS MCU RENE..
$79.64
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.75
Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set ..
$106.18
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.64
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.64
Includes maps calibrations for all firmware M74, М74CAN and М74к.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the..
$53.09
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.46
Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/butto..
$79.64
Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any e..
$86.27
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.46
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.65
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$491.86
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to v..
$51.76
The module is designed to read and write FLASH memory of ECU MT86 installed on a KIA/Hyundai. Working with these types of ECU's is via the J2534 device
ECU MT86 is a read only field calibrations. Recording is supported for the following formats:
Firmware reads th..
$42.44
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$504.37
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.64
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the abi..
$79.64
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.09
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.64
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.55
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.73
The module allows you to convert any serial in three-mode version. Support switching complete sets of calibrations, including identifiers and the mask of DTC. Toggle options: channel or DTV channel ДК2. Provided disabling the fuel pump (with programmable delay) and the injectors individually for ..
$79.64
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.82
The module for the new version of the program Chiploader NG
Module [51] Bosch MEDC17 - Bench is designed to read and write the internal memory (flash and eeprom) of the processor is Tricore ECU Bosch MEDC17 on the table without disassembling the ECU.
Detailed information ..
$258.17
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.40
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.46
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.46
The module is intended for editing of data logger units UAZ M86I and Микас12 (GAS) with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training da..
$26.55
The module is intended for editing of data logger units M74.5 (6.38), M75 and vases M86I with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the train..
$26.55
The module is intended for editing of data logger units M74 (storing training data in flash CPU) and М86, ON 'VAZ'. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely fr..
$26.55
Module EDC17/MED(G)17 (Kia/Hyundai) - OBD2 is designed to write FLASH memory of ECU Bosch EDC17C08, Bosch, EDC17CP14, Bosch MED(G)17.9.8 via the J2534 device.
Please note that this module can only record the previously prepared serial tuning or firmware!
..
$28.35
Module Bosch ME17.9.11/12-OBD2 is designed to write FLASH memory of ECU Bosch ME17.9.11, Bosch ME17.9.12 via the J2534 device. Please note that this module can record only serial firmware!
..
$11.71
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.88
Development of the module is not over
Functionality you can see in the coverage map.
..
$62.38
Development of the module is not over
Functionality you can see in the coverage map.
..
$62.38
Development of the module is not over
Functionality you can see in the coverage map.
..
$62.38
Development of the module is not over
Functionality you can see in the coverage map.
..
$62.38
FID: 64, 103
Service module for identification and virtual reading of the firmware control unit Denso 32920-4xxxx. The ECU is powered by a Renesas SH7052 CPU.
Read the actual flash memory of a given block is only possible by drilling a fairly large hole in the hull f..
$119.94
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.09
License 85, may be applicable at the discretion of the licensee (user) to the work:
Correction of mileage readings with recalculation of checksums in the read EEPROM area of the processor firmware,
in DSG DQ200, DSG DQ200_MQB, DSG DQ200 G2, DSG DQ250 E/F(02E) units installed on..
$79.64
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.18
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.82
Module allow to make the chip tuning Hyundai Genesis/Equus, Kia Cadenza/Quoris/Sorento Prime engines 3.3/3.8/5.0 l, equipped with ECU Delphi MT86.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delph..
$132.73
Module allow to make the chip tuning Hyundai/Kia with engines V6 2.7/3.3/3.8 L, equipped with ECU Delphi MT38.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delphi MT38 by means of the loader CombiL..
$132.73
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.82
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.27
A cable for overwriting an ECU with an 81 pin connector using a Combiloader and the corresponding modules.
..
$33.18
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.71
The program in Russian and English languages.
Universal programmer a large number of microcontrollers from Microchip, Atmel, Cypress, ST, etc., and also chip FLASH/EEPROM (currently more than 13000 chips). Connect to PC and power to the programmer through the USB port of the computer (5v).
..
$122.08
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.63 $73.00
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.09
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.88
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.38
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.09
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.82
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.88
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.64
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.64
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.09
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.82
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.88
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.88
ORANGE-5 is a modern programmer for working with microcontrollers and memory chips. The feature of this series of devices is the built-in HPL macro language, which allows easy addition of support for new types of chips in full compliance with manufacturers' recommendations. This approach ensures ..
$198.24
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.82
![[54] BOSCH ME17.8.8 - OBD2](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[54] BOSCH ME17.8.8 - OBD2")
