The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.33
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
Includes the following modules:
module SRS AIRBAG Renault Continental Temic Motorola OBD2
Allows clearing CRASH DATA in blocks on the processors 9s12XDT384+95640 .
These units were installed in the cars of Renault Fluence /Megane III / Latitude / ScenicIII / KangooII / TwingoII
..
$79.74
FID: 337
A module for reading and writing Shindengen control units installed on Honda motorcycles.
Honda Moto Shindengen V850/RH850 K-Line (FID:337)
Sihndengen engine control units are powered by Renesas V850/RH 850 series processors with 256/384Kb internal flash memo..
$247.15
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, th..
$239.73
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.74
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.60
FID: 64, 103
Service module for identification and virtual reading of the firmware control unit Denso 32920-4xxxx. The ECU is powered by a Renesas SH7052 CPU.
Read the actual flash memory of a given block is only possible by drilling a fairly large hole in the hull f..
$119.87
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)
Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Mar..
$239.73
1.6 L CFNA/CFNB/CLRA 7GV K-Line (Marelli 7GV/832KB) [RD/WR/CK]
1.4 L CGGB K-Line (Marelli 7GVE/832KB) [RD/WR/CK]
1.6 L BFQ K-Line (Simos 3.3 A/512KB) [RD/WR/CK]
1.4 L BUD/BXW/CGGA/CGGB K-Line (Marelli 4HV/832KB) [RD/WR/CK]
1.6 L BSA/BSE/BSF Calibration K-Line (Simos 7...
$66.45
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
The module allows you to view and edit statistics (mileage, fuel consumed), speed limit and transmission protection parameters in the configuration files *.cfg ECU Continental CM2150, CM2200, CM2220, CM2350, CM2880.
Read using the Combiloader programmer by the Cummins CM2xxx module. It is pos..
$239.21
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
Designed for chip-tuning ECU Delphi and Delphi MT05 MT05.2, installed in various types of motorcycles.
Control units Delphi MT05, and MT05.2 differ by the type of processor and size of FLASH memory. For Delphi MT05 FLASH size is 128kB, for Delphi MT05.2 — 256Kb. The type of ECU is determined ..
$106.32
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices.
The modules support the following types of ECUS:
MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB.
MagnetiMarelli MM7GV:..
$66.45
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.80
License 15, may be applicable at the discretion of the licensee (user) to the work:
ECU on the NEC 34+24C16 microcontroller:
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording (program area + calibration)
..
$79.74
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles.
..
$106.32
License 17, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording EEPROM 24c04 or 93c56 (depends on the type of panel) by OBDII or direct connection on the table (connection in the help).
Correction of odometer readings by OBDII or direct connecti..
$66.45
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.87
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.89
Honda: Accord 2003-2005 7 (Matsushita RBA/RBB SH7055/512KB) [VR/WR/CK]
Honda: Accord 7 2006-2007/TSX 2004-2005 (Matsushita RBA/RBB SH7055/512KB) [VR/WR/CK]
Acura: TSX 2006 (Matsushita RBB A56-A62 SH7058/1MB) [VR/WR/CK]
Honda: Accord/CR-V/Element/Legend/Odyssey/Ridgeline (Kei..
$93.03
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.80
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.89
Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering.
..
$3 236.37
1.3 L, 1.5 L ZJ/ZY (Mazda2 2011+) [RD/WR/CK]
1.5 L ZY (US Mazda2 2011+) [RD/WR/CK]
1.6 L Z6 (Mazda3 2010+) [RD/WR/CK]
1.8 L, 2.0 L, 2.5 L L8/LF/L5 (Mazda6 2008+) [RD/WR/CK]
2.0 L, 2.3 L, 2.5 L LF/L3/L5 (Mazda3/5/CX7 2010+) [RD/WR/CK]
2.0 L LF (Mazda Biante 2013+/..
$93.03
Ford Mondeo 4: 1.6 L Sigma Ti-VCT 110/125PS (EMS2101) [RD/WR/CK]
Ford Mondeo 4: 2.0 L Duratec HE (ESU312 Galaxy/S-Max 2006) [RD/WR/CK]
Ford Mondeo 4: 2.0 L, 2.3 L Duratec HE (ESU412/415) [RD/WR/CK]
Ford Mondeo 4: 2.5 L I5 Duratec 225PS (ME9.0) [WR/CK]
..
$93.03
Ford Fiesta: 1.25L, 1.4L Sigma Ti-VCT (EMS2102) [RD/WR/CK]
Ford Fiesta: 1.6L Sigma Ti-VCT (EMS2101) [RD/WR/CK]
Ford Fiesta: 1.6L Sigma Ti-VCT USA [AE81] (EMS2205) [RD/WR/CK]
Ford Mondeo 4: 1.6L Sigma Ti-VCT 110/125PS (EMS2101) [RD/WR/CK]
..
$66.45
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
Ford Focus 3: 1.0 L GTDI Ecoboost 100/125PS (MED17) [RD/WR/CK]
Ford Kuga 2: 1.6 L GTDI Ecoboost 150PS FWD (MED17) [RD/WR/CK]
Ford Fiesta: 1.0 L Ecoboost GTDI 100/125PS (MED17) [RD/WR/CK]
..
$66.45
Ford Focus 3: 1.6 L Ecoboost GTDI 150/180PS (MED17) [RD/WR/CK]
Ford Mondeo 4: 2.0 L Ecoboost GTDI 200/240PS (MED17) [RD/WR/CK]
..
$66.45
Ford Focus 3: 2.0 L DW10C STAGE 5 140/163PS (DCM3.5) [VR/WR/CK]
Ford Kuga 1: 2.0 L DW10C STAGE 5 140/163PS (DCM3.5) [VR/WR/CK]
Ford Kuga 2: 2.0 L DW10C STAGE 5 140/163PS (DCM3.5) [VR/WR/CK]
Ford Mondeo 4: 2.0 L DW10C STAGE 5 140/163PS (DCM3.5) [VR/WR/CK]
Ford Mondeo 4:..
$93.03
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.80
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.74
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.73
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
$359.60
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.73
The module is designed to work with blocks motor control EMS3130, EMS3132, EMS3134 used in vehicles Renault, Dacia, Nissan. Supported reading and writing as control unit as a whole, and only in the area of calibration, validation and correction checksums, ability to work with files in formats oth..
$66.45
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
$359.60
The module is designed to work with blocks motor control EDC16CP31-6 and EDC16CP31-8, installed in the vehicles of MB Sprinter 906/909 (Classic). Supported read, write, calibration, validation and correction of the COP.
Sprinter (906) CDI 2.2 L (EDC16CP31-6) [RD/WR/CK]
Sprinter Clas..
$93.03
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.73
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.87
Module for the calibration firmware different motorcycles BRP, Ducati, Arctic Cat, Stels, Dinli, etc. with the control units Continental M3C.
Available the following cards:
The calculated mass air flow to throttle position, correction of the estimated air flow correction volume..
$299.66
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.53
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71.
Available the following cards:
The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficien..
$239.73
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.89
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.73
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.66
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
Mazda: 1.6L Z6 AT (Mazda3 2004+) [RD/WR]
Mazda: 1.6L Z6 MT (Mazda3 2004+) [RD/WR]
Mazda: 1.3L ZJ (Mazda Demio 2003+) [RD/WR/CK]
Mazda: 1.8L, 2.0L, 2.3L L8/LF/L3 (Mazda3/6/CX7 2003+) [RD/WR/CK]
Mazda: 2.0L LF USA (Mazda3 -2009/1MB) [RD/WR/CK]
Mazda: 1.3L N3 (Mazda..
$93.03
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.32
Supports only the following Honda/Acura:
Accord7/TSX 03'-07' ECU 7055 [512]Matsushita K 37805-RBA-Xxxx; 37805-RBB-Xxxx
Accord7 05'-07' ECU 7058[1024]K Keihin 37805-RAD-Xxxx
2006 TSX ECU 7058[1024]Matsushita K 37805-RBA-Xxxx
Legend/CR-V 02'-07' ECU 7058[1024]K Keihin 3780..
$93.03
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.61
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
$239.73
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.81
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
Mazda: 1.5L, 2.0L, 2.5L SKYACTIV-G P5/PE/PY (Mazda3/CX5/6 Mitsubishi) [RD/WR/CK]
Mazda: 2.5T SKYACTIV-G PY (Mazda CX9 Mitsubishi) [RD/WR/CK]
Mazda: 1.5L, 2.0L, 2.5L SKYACTIV-G P5/PE/PY (Mazda3/CX5/6 Denso) [RD/WR/CK]
Mazda: 1.5L, 2.0L, 2.5L SKYACTIV-G P5/PE/PY (Mazda3/CX5/6 ..
$93.03
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.73
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.53
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.89
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong.
Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle.
Works through the J2534 interface.
ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato..
$93.03
Read/Write firmware
Read/Delete errors
Check/Fix the checksum
The module automatically determines the size. Supports all markets. Read a full Hour, recording 10-15 minutes of cars and trucks. Machinery is the ECU is written HOUR SH7059 processor.
Used processors SH7058, ..
$106.32
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to v..
$51.83
Yamaha F40/50/60 MH8102F(ECU is not filled). RFX Yamaha nitro MH8104F(ECU flooded).MH8106F, MH8115F.
..
$119.61
Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor.
Available the following cards:
Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure ..
$239.73
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
Working with this type of ECU is 'on the bench'.
Car Volvo S60 Y283 I5T_13A200_257_Y283_2.5L_US_AWD 31411200AA 2010 Denso SH72543 31312651AB Bench 69
Car Volvo XC60 Y413 Y413_A_MP_150hp_Eu6b 31669250AB 150 2010 Denso SH72546 31452623 Bench 69
Car Volvo V40 Y555 Y555_M_LP_150hp_Eu6b ..
$132.89
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
For chip-tuning cars Opel turbocharged a series of engine Z20LEL, Z20LEH, Z20LER.
..
$93.03
This module allows you to make chip-tuning BMW MS42 ECU (engine MT52TU, Serie 3 E36, 5 E39 Serie) and MS43 (E46 Serie 3, Serie 5 E39, X5 E53). The module works in conjunction with ChipTuningPRO 7 or higher. The ECU programming is done using the loader CombiLoader.
Maps contain more than 150 c..
$93.03
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.60
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
The module is designed for operation with control units petrol engines and turbo diesel installed in vehicles Land Rover Freelander 2, Evoque, Discovery Sport etc. Supported read, write, calibration, validation and correction of the COP.
Discovery 3 2.7L TDV6 (SID201/SID204) [RD/WR/CK]
..
$159.47
The module is designed to work with the engine control units (ECUs) produced by Continental for SGMW and Geely cars. For SIM2K-D51/51.4/SCE60, reading and writing through the diagnostic connector is supported, while for Easy U2/U2.5/U2W/U3.6, connection "on the bench" may be required. Checksum ve..
$93.03
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
The module is designed to work with the ECU from diesel engines 1.6, 2.0, 3.0 and 4.2 TDI are installed on passenger cars and crossover vehicles group VAG, approximately 2010. Supported entry, verification and correction of the COP.
2.0L, 3.0L TDI (EDC17CP04/EDC17CP14/EDC17CP..
$119.61
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.89
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.89
The module is designed to work with the ECU engine 1.0 TSI, 1.2 TSI, 1.4 TSI, 1.6 MPI, 2.0 TSI, 3.6 FSI, 1.0 MPI, etc. installed on vehicles group VAG (VW Golf 7, Polo, Passat B8, Skoda Rapid, Octavia A7, Tiguan, Jetta, Audi A1, A3, etc.). Supported entry, verification and correction of the COP.
..
$119.61
Module is designed to work with the ECU of 2.0L Delphi DCM6.2A/DCM6.2C diesel engines installed on PSA group cars, working through a diagnostic connector. Supports reading, writing, checking and correcting checksums:
Citroen/Peugeot 2.0L HDi (DCM6.2A) [RD/WR/CK]
Citroen/Peugeot 2.0L..
$93.03
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
The module is designed to work with the ECU EDC7/EDC16/EDC17 diesel engines Mitsubishi Fuso Canter. Supported read, write, review, and correction of the COP. For some cars with ECU EDC7/EDC16 for writing may require a direct connection to the connector block.
Fuso Canter (EDC7C4-6/EDC16C3..
$132.89
The module is designed to work with ECUS that are installed in vehicles with Ford diesel engines 1.4, 1.5, 1.6 l Supported read, write, review, and correction checksums.
Ford Focus 3: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
Ford Mondeo 4: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
..
$93.03
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
The module is designed to work with ECU EDC17 installed with a diesel engine 6.7 l in the Ford. Supported read, write, review, and correction of the COP.
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [BC3A] [RD/WR/CK]
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [DC3A/FC3A] [RD/WR/CK..
$132.89
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.73
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
The module is designed to work with ECU Mitsubishi and Denso installed with gasoline engines in vehicles Mazda with the 2019 model year. Supported read, write, review, and correction of the COP.
1.5L, 2.0L, 2.5L SKYACTIV-G P5/PA/PE/PY MY2019 (Mitsubishi) [PYFA] [RD/WR/CK]
1.5L, 2.0L..
$93.03
The module is designed to work with the ECU SID208 installed on vehicles with diesel engine 2.2 l Supported read, write, razblokirovka the ECU to record the modified firmware, and test and correction checksums.
Citroen/Peugeot 2.2 L HDi (SID208) [WR/CK] (write after unlocking in BSL)
..
$93.03
The kit contains modules:
Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L.
Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particu..
$66.45
RoadPartner cars TagAz/TaGeR/SsangYoung Rexton with engines 2.3/2.8/3.2 L. Intended for read-write FLASH memory via the diagnostic connector.
..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$119.61
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$66.45
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
$239.73
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
$239.73
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
$239.73
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector.
ECU Continental EMS3155 ustanavlivaetsya on engines 1.2 T.
ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L.
ECU Bosch EDC17C84 i..
$132.89
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module is designed to work with the ECU built on microcontrollers SH72513/SH72543/SH72544 installed on diesel vehicles of different brands. Supported read, write, and recalculation of checksums.
Kia/Hyundai 2.5 L CRDI (DCM3.7AP) [RD/WR/CK]
Opel/Chevrolet 2.0 L, 2.2 L CDTI (DCM3...
$132.89
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
The module is designed to work with the ECU Kefico/Denso processor SH72546 installed in cars with a diesel engine of 2.5 l, standards of toxicity Euro-6. Supported read, write, review, and correction checksums.
Kia/Hyundai 2.5L CRDI (SH72546) [RD/WR/CK]
Hyundai Euro 5 (Denso SH7058S..
$93.03
Updated version of programmer XPROG-M v5.55 is intended for programming of new microcontroller and memory chip manufacturers, Motorola, Infineon, Micronas, Texas, Atmel, ST, National(CR16), M35080 and immobilizer EWS-3, CAS4 5M48H including software is protected from reading.
Authorization th..
$97.89
The module is designed to work with blocks EDC16C39, which are installed on vehicles UAZ Patriot, hunter with diesel engines ZMZ and Iveco. Supported reading calibrations (for Iveco), a record full of files (and calibration for the Iveco), verification and correction checksums.
Patriot/Hu..
$66.45
The module is designed to work through the diagnostic connector of a car with Delphi DCM6.2 engine control units used in VAG concern cars. Virtual reading, writing, checking and correction of checksums are supported.
1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/RD/WR/CK]
..
$132.89
Toyota Denso Petrol 5.7i module for chip tuning of Toyota Sequoia, Tundra, Lexus LX570, etc. with 5.7-liter 3UR-FE and 3UR-FBE engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the authors of the module (V. Kulikova and A. Tesla).
..
$239.21
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.73
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
The module is designed for chip tuning of BMW cars with the N55B30 engine.
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by d..
$132.89
The module is designed for chip tuning of Audi A4, A5, VW Amarok, Crafter, Passat, Transporter cars with 2.0L TDI and 2.5L TDI diesel engines.
Allows for professional chip tuning of Bosch EDC17CP20 control systems. The possibility of correctly disabling the ecology of EGR, DPF, SCR (AdBlue).
..
$199.34
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.89
The Toyota Denso Diesel 4.5D (1VD-FTV) module with 76F0070 processor is designed for chip tuning of Toyota cars with 4.5L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported..
$239.21
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.73
Module for motor vehicles GAS, SHAANXI, FAW with the control units EDC17CV44/54 using Mscan EDS-24.
..
$66.45
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
The module is designed to work with the ECU EMS3155, SID309, Hitachi CPU RH850 working on the UDS Protocol and installed in vehicles with petrol engines 1.2 l and diesel 1.5 l Supported read, write, review, and correction checksums.
1.2 T EMS3155 UDS (TC1782/2.5 MB) [RD/WR/CK]
1.5 L..
$132.89
Supported reading (where possible), write via OBD and correction KS for vehicles with engines of 1.1, 1.4, 1.6 liters.
Kia/Hyundai: 1.4L, 1.6L (ME17.9.11/12/13) [RD/WR/CK]
Kia/Hyundai: 1.4L, 1.6L (ME(G)17.9.21/17.9.21.1) [RD/WR/CK]
Kia/Hyundai: 1.6L, 3.0L (ME17.9.2/ME(D)(G)17...
$93.03
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
The module is designed for chip tuning of VAG cars (Skoda, Audi) with 1.0TFSI and 1.4TFSI engines equipped with Bosch MED17.1.27. Please note: Third-party developer module! Technical support from the module author (KHN09). Firmware for Bosch ME17 controllers is saved by default in SMS-Soft Contai..
$159.47
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
The Bosch MD1CP002 (DE 832) BMW module is designed for chip tuning of BMW cars with B57D30xx and B47D20xx diesel engines.
Installed on:
3rd G20 Series
5th series G30 and G31
6th Series G32
7th series G11 and G12
8th series G14, G15 and G16
X3 S..
$332.24
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
The module is designed for chip tuning of Korean-made cars of 2018 and newer with GDI gasoline engines equipped with Kefico CPEGD2.20.1 / CPEGD2.20.2 / CPEGD2.20.3 / CPGDSH2.26.1 / CPGDSH2.26.3 / CPGPSH2.14 ECUs.1.
These ECUs are used on cars such as:
Hyundai Elantra, Avant..
$265.79
The module is designed for chip tuning of Suzuki Jimny, Liana, Grand Vitara, Swift, SX4 cars with 1.3L, 1.5L, 1.6L, 2.0L, 2.4L engines equipped with Denso ECU with SH7055 and SH7058 processors.
Pay attention:
A third-party developer module! Technical support from the author..
$79.74
Toyota Denso Diesel 2.0D module for chip-tuning Toyota cars (Auris, Avensis, Corolla, Verso) with diesel engines 2.0L 1CD-FTV / 1AD-FTV, Denso ECU, 76F0004 320kB, 76F0040 368kB, 76F0039 496kB, 6F0038 736kB processors, 76F0085 992kB.
Pay attention:
Third-party develope..
$239.21
The module is designed for chip tuning of VAG cars with gasoline engines 1.8TFSI and 2.0TFSI of the third generation: Audi A4/ A5 / A6, Audi Q3 / Q5, Audi TT, Porsche Macan, Skoda Octavia, Skoda Octavia RS, VW Passat, VW Polo GTI, VW Jetta, VW Tiguan, etc.
Note:
Third-party mod..
$239.21
The Bosch EDC7UC31 GAZ module is designed for chip tuning of GAZ and MAZ cars with YAMZ-5344.20, YAMZ-53416, YAMZ-53441.20, YAMZ-53442, YAMZ-536, YAMZ-53601, YAMZ-53602, YAMZ-53603, YAMZ-53613, YAMZ-53622, YAMZ-53623, YAMZ-53624, MMZ-245 diesel engines.7.
Supported firmware (softwa..
$265.79
The Bosch EDC7UC31 KAMAZ module is designed for chip tuning of KAMAZ vehicles with diesel engines of the KAMAZ-740 family.
Supported firmware (software versions P702.141, P986.310), EDC7UC31 KAMAZ module:
702V141_740.60-360-290812_5460-4010142-01
702V141_740.60-360-29..
$265.79
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
The Toyota Denso Diesel 2.5 module is designed for chip tuning of Toyota cars with 2.5 diesel engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
Supported software versions, Toyota Denso Die..
$239.21
Bosch EDC17C64 module is designed for chip tuning of Audi A3 / A4 / A6 / Q5, VW Golf7 / Sharan / Tiguan, Skoda Octavia and others with 1.6L and 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
..
$132.89
Module allow to make the chip tuning Hyundai/Kia with engines V6 2.7/3.3/3.8 L, equipped with ECU Delphi MT38.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delphi MT38 by means of the loader CombiL..
$132.89
The module is designed for chip tuning Hyundai(IX35, IX55, Santa Fe, Tucson) and Kia(Carnival, Mohave, Sorento, Sportage) with diesel engines 2.0 CRDi (D4HA, 184HP), 2.2 CRDi (D4HB, 197HP) and 3.0 V6 CRDi (D6EB, 247HP).
Please note:
Third-party module developer! Technical s..
$106.32
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.73
The module is designed for chip-tuning VAG cars with engines 1.8 T, 2.0 T, equipped with Bosch MED17.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Sof..
$159.47
The module is designed for chip-tuning VAG group diesel engine 3.0 L ECU Bosch EDC17CP44.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are stored by default in the format of SMS-Soft..
$132.89
The module is designed to work with ECU Bosch ME7.9.20 installed on the Nissan X-Trail T31 petrol engine volume of 2.5 L. is Supported by the record validation and correction checksums.
EFI ME7.9.20 Calibration (ST10F275 Bosch EXT/512KB) [WR/CK]
..
$66.45
Kit modules:
Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector.
Isuzu Transtron ..
$106.32
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.45
Hyundai and Kia: Carens, Cerato new, Magentis, Sonata, Sorento, new Sportage, ix35 and the other with an engine capacity of 2.0 and 2.4 L.
2.0L, 2.4L (SIM2K-140) [RD/WR/CK]
2.0L, 2.5L (SIM2K-D160) [RD/WR/CK]
2.0L, 2.4L (SIM2K-141/142/341) [RD/WR/CK]
2.0L (SIM2K-C201) [RD..
$93.03
The module allows you to produce professional chip tuning Mitsubishi Outlander XL with engines of 2.4 L and 3.0 L (manual and CVT) and Mitsubishi ASX with dvigatelem 2.0 L and Citroen C-Crosser and Peugeot 4007 made on the platform of the Outlander. Has no analogues on the number of calibrations ..
$79.74
The module is designed for chip tuning of VAG group cars with gasoline engines, Bosch MG1CS001 ECU, for example:
Audi A1 2.0 TFSI
Audi A3 2.0 TFSI
Audi A4 2.0 TFSI
Audi A5 2.0 TFSI
Audi A7 2.0 TFSI
Audi Q2 2.0 TFSI
Audi Q3 2.0 TFSI
Audi Q5 2.0 TFS..
$186.05
The module is designed for chip tuning of Ssang Yong Actyon, Korando, Rexton, Rodius, Stavic, etc. cars with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulik..
$132.89
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
The module is designed for chip tuning of VAG cars with 1.8 TFSI and 2.0 TFSI petrol engines of the 3rd generation: Audi A4 1.8 TFSI, Audi A5 1.8 TFSI, Audi A5 2.0 TFSI, Audi A6 1.8 TFSI, Audi Q5 2.0 TFSI, Skoda Octavia 1.8 TFSI, Skoda SuperB
Pay attention:
A third-party de..
$239.21
The Toyota Denso Diesel 3.0D (1KDFTV) module with 76F0040GD, 76F0039AGD, 76F0070, 76F0085 processors is designed for chip tuning of Toyota cars with 3.0L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the modul..
$239.21
Bosch EDC17C74 module is designed for chip tuning of Audi A3 / Q2, VW Golf / Passat / Tiguan, Skoda Superb / Kodiaq and others with 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
By default, the firmwar..
$132.89
Module allow to make the chip tuning Hyundai Genesis/Equus, Kia Cadenza/Quoris/Sorento Prime engines 3.3/3.8/5.0 l, equipped with ECU Delphi MT86.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delph..
$132.89
The module is designed for chip tuning Hyundai Santa Fe, Hyundai Tucson, KIA Carnival, KIA Sorento Prime, KIA Sportage diesel engines 2.0 CRDi and 2.2 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmw..
$106.32
The module is designed for chip-tuning, car Hyundai I40, Hyundai IX35, KIA Soul diesel engines 1.6 CRDi and 1.7 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmware families Bosch МEDC17 are stored by..
$106.32
The module is designed for chip tuning Hyundai(I30, I40, IX35, Santa Fe) and Kia(CEE'd, Optima, Soul, Sportage, Venga) with diesel engines 1.6 CRDi, 2.0 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Fir..
$106.32
The module is designed for chip-tuning VAG group (VW Amarok, VW Crafter, VW LT) with a diesel engine capacity of 2.0 L, ECU Bosch EDC17C54.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC..
$132.89
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
The module is designed for chip-tuning VAG group (VW Tiguan, Touareg) with a diesel engine capacity of 3.0 L, Bosch ECU EDC17CP14.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are st..
$132.89
The module allows you to produce a professional chip tuning for Renault Logan, Renault Sandero, Nissan Almera engine 1.6 L, automatic transmission, equipped with ECU Continental/Siemens EMS3134.
Supported versions:
REA820
REA830
Features of the module:
The possibil..
$79.74
The module is designed for chip tuning of Hyundai and Kia cars with EURO-6 diesel engines equipped with Denso ECU with SH72543/SH72546 processors.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported s..
$265.79
The module is designed for chip tuning of Great Wall Hover cars and others with 2.0 TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported software versions:
&..
$106.32
The Bosch EDC17C64 GAZ module is designed for chip tuning of GAZ group cars with VAG 2.0TDi diesel engines.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
The firmware of the Bosch EDC17 family controllers ..
$106.32
The Toyota Denso Diesel 2.8D module supports all software versions, including GEN3; processors D76F0196F1 (1536Kb), D76F0219F1 (2048kB), R7F701202 (4096Kb). Designed for chip tuning of Toyota cars with 2.8L diesel engines, Denso ECU.
Pay attention:
Third-party developer mod..
$239.21
The module is designed for chip-tuning of cars of the VAG group (Audi A3/A4/A5/A6/Q3/Q5/TT, Skoda Superb, VW Golf, VW Passat, VW Tiguan, etc.) with a diesel engine capacity of 2.0 L, EDC17C46 Bosch ECU.
Please note:
Third-party module developer! Technical support from the a..
$132.89
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
The Nissan Denso Diesel 2.5 TDI SH7059 module is designed for chip tuning of Nissan Navara, Pathfinder, Cabstar, Murano, NV300, Caravan, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7059 processors.
Pay attention:
Third-party developer modules! Techni..
$132.89
The Nissan Denso Diesel 2.5 TDI SH7058 module is designed for chip tuning of Nissan Cabstar, Condor, Navara, NP300, Pathfinder, Vanette, X-Trail, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7058 processors.
Pay attention:
Third-party developer module..
$132.89
The module is designed for chip tuning of Chevrolet Captiva, Cruze, Orlando, Daewoo Winstorm, Opel Antara, etc. with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kuli..
$132.89
Toyota Denso Diesel 2.4 D module for chip tuning of Toyota (Hilux) cars with 2.4 L 2GD-FTV diesel engines, Denso ECU, processors D76F0196F1 1.5 MB, D76F0219F1 2MB.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
..
$239.21
Toyota Denso Diesel 2.2 D module for chip tuning of Toyota/Lexus cars (Verso, Avensis, RAV4, Auris, IS220) with 2.2 L 2AD-FHV / 2AD-FTV diesel engines, Denso ECU, processors 76F0039 496kB, 6F0038 736kB, 76F0085 992kB.
Pay attention:
Third-party developer modules! Technical ..
$239.21
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.74
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$93.03
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.74
License 08, may be applicable at the discretion of the licensee (user) to the work:
The work is done by upgrading the Flash file.
Works as an editor.
DENSO engine control units on NEC 76F00xx processors with firmware size are supported 256, 320, 368, 384, 496, 736, 992, 1024.
..
$79.74
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
The Bosch EDC7UC31 MAZ / KRAZ / URAL module is designed for chip tuning of MAZ, KrAZ, MZKT, Ural cars and generator sets with diesel engines.
Supported firmware (software versions P766.120), module EDC7UC31 MAZ / KRAZ / URAL:
P766_120_MAZ_YAMZ-650_C_14_w_o_Cr_Ct
..
$265.79
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$239.21
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.89
The modules are designed to read / write flash memory of ECU Siemens vehicle Ford Focus 2, C-Max, Kuga engines 1.4...1.6 l (2004...2009), Ford Fiesta, Fusion engines 1.2...1.6 l
..
$66.45
The modules are designed to read / write flash memory of ECU Visteon ESU-131/312/411/412/415/418 vehicle Ford Focus 2, C-Max, Kuga engines 1.8...2.0 l (2004...2010) and Ford Mondeo 4 S-Max, Galaxy with 2.0 engine...2.3 l (2004..2011 onwards)
..
$106.32
For chip-tuning Ford Focus II with engines 1.4—1.6 L without adjustable phase timing, ECU Siemens SIM28.
..
$106.32
For chip-tuning Ford Focus II with engine 1.6 L with adjustable phase timing, ECU Siemens SIM29.
..
$106.32
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.89
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.74
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
For chip-tuning Opel cars with engines Z10XEP, Z12XEP, Z14XEP.
..
$93.03
The module is intended for recording and(or) region calibration ECU Siemens EMS2204, installable in particular on cars Ford Focus 3 engine 1.6 l
..
$66.45
For chip-tuning Opel cars with engines Z16XER and Z18XER.
..
$132.89
For chip-tuning Chevrolet Cruze, Chevrolet Orlando engines Z16XER and Z18XER.
..
$132.89
For chip-tuning of cars Tagaz Tager/Road Partner and Ssang Yong Musso, Actyon, Rexton, Kyron petrol engines 2.3/2.8/3.2 L.
..
$93.03
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.73
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.73
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.60
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
$299.66
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.73
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
Cars Renault Logan/Sandero Stepway/Megane/Fluence with engines of 1.2 L and 1.6 L.
..
$66.45
For chip-tuning Chevrolet Captiva cars with engines 2.4 L.
..
$106.32
For chip-tuning cars Mitsubishi Lancer 10 with engines of 1.5 L.
..
$79.74
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
$239.73
The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb.
Currently it supports the following calibration: the ignition timing for h..
$239.73
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb.
Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture,..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.33
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$53.16
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$53.16
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$106.32
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$106.32
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.74
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the abi..
$79.74
For chip-tuning cars Mitsubishi Lancer 10 (except vehicles with engines of 1.5 L).
..
$79.74
For chip tuning cars Chevrolet Captiva and Opel Antara with the engine volume of 3.2 L.
..
$93.03
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A.
..
$359.60
Module for the calibration firmware and atmospheric turbocharged snowmobiles Arctic cat with power management Denso 32920-49Xxx processor-based Renesas SH7052.
..
$239.73
Supports reading and writing c petrol Mazda Sky Active engines of 2.0 and 2.5, which require the ECU manufactured by Denso.
Car Mazda 6 GJ 2.5L Skyactiv-G PY3GEE000PY0B060 192 DENSO SH72543 PY3G-188K2-E OBD 33
Car Mazda 6 GJ 2.5L Skyactiv-G PY3HEG000PY0B060 192 DENSO SH72543 PY3H-18..
$66.45
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.89
Toyota Avensis cars with 2ZR-FAE gasoline engines, volume 1.8. Cost: 3000r.
Supported Software:
89663-01032-
89663-01121-
89663-02023-
89663-02161-
89663-02162-
89663-02172-
89663-02173-
89663-02182-
89663-02183-
89663-0..
$39.87
VW Touran, Golf, Passat, Transporter, Caddy cars with engines AVQ,BKC,BMT,BLS, etc. with a volume of 1.9L
Supported Software:
1037367485P379U6FP
1037368205P213U6FT
1037370254P213U8C3
1037370811379U85B6
1037371094379U85B6
1037371250379U85B6
..
$39.87
Toyota Corolla cars with 1ZR-FE, 3ZZ-FE 1.6 petrol engines
Supported software:
89663-02240-A
89663-02241-
89663-02270-A
89663-02482-
89663-02483-
89663-02491-
89663-02492-
89663-02502-
89663-02503-
..
$39.87
Toyota Camry, Rav4, Avensis cars with gasoline engines 1AZ-FE, 3ZR FAE, 3ZR-BE, 3ZR-FE, volume 2.0
Supported software:
89663-05A11-
89663-06460-
89663- 06B40-
89663-06E10-
89663-42053-
89663-42192-
89663-42590-
89663-42600- Ah
..
$39.87
Toyota Camry, Rav4 cars with 2.4L 2AZ-FE petrol engines
Supported versions:
89663-02802-
89663-02822-
89663-06431-
89663-33021-
89663-33041-
89663-33691-
89663-33701-
89663-33702-
89663-33720-A
89663-33721-
..
$39.87
Toyota Camry, Highlander, and Lexus cars with 2GR-FE 3.5l gasoline engines
Supported BY:
89663-06772- 89663-06G70- 89663-06P00- 89663-0E050-A 89663-0E340- 89663-22290-A 89663-30A11- 89663-33340-A 89663-33341- 89663-33640-A 89663-33641- 89663-33642- 89663-33650-A 8966..
$39.87
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.73
The module is designed for Chip tuning ECU SID211 installed on the following models Ford Transit, Ranger, Tourneo Connect diesel 2.0 L Ecoblue engine.
List of cars:
Car Ford PANTHER 2.0 105/130PS S/S GK21-14C204-AAA Continental TC1791 OBD 88
Car Ford PANTHER 2.0 105/130PS ..
$93.03
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.80
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Panasonic processor Infineon Tricore TC197X with internal flash memory 4Mb.
..
$239.73
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb..
$79.74
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The KMS MD1CE100 module allows you to view, compare and edit the firmware files of Kamaz K5 cars with an R6 engine (Bosch MD1CE100 ECU).
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, DPF, EGR, AdBlue, ..
$664.47
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
The module allows you to edit the firmware of SUBARU cars (2.0 engines) with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). Tables of UOZ, mixture composition, throttle position, torque request, error mask, etc. are available.
Supported Software:
E2UD00..
$39.87
Toyota Camry cars with 2AR-FE engine, volume 2.5L
Supported software:
89663-06791-
89663-06794-
89663- 06A31-
89663-06A35-
89663-06A45-
89663-MODUM-
89663-33B51-
89663-33B52-
89663-33B60-
89663-33D71-
89663-33G81-
..
$39.87
Toyota Land Cruiser 150 cars with 1GD-REV diesel engine Cost: 3000r.
Supported Software:
89663 - 60X23
89663 – 60X24
89663 – 60X26
89663 – 60X27
89663 – 60X28
89663 – 60X29
89663 – 60Z31
89663 – F0594
89663 – F0595
89663 – F0599
..
$39.87
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.87
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.81
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Supports reading and writing diesel Mazda with SH7058 processor in QFP-256 (none BGA) and software on the basis of RF7x
..
$39.87
Module 3 supports reading and writing of the following types of processors of the M32r series used in both the engine control unit and the active central differential control unit:
MH8104F_(512K) by CAN
MH8104F_(512k) by Kline (repair/restoration)
MH8106F_(1024K) by CAN
..
$93.03
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.68
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
$299.66
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.96
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
$239.73
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.81
ORANGE-5 is a modern programmer for working with microcontrollers and memory chips. The feature of this series of devices is the built-in HPL macro language, which allows easy addition of support for new types of chips in full compliance with manufacturers' recommendations. This approach ensures ..
$198.24
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
MDflasher software for odometer adjusting, to work with the immobilizer, the Airbag, and als..
$39.87
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
FID: 238, 242, 245, 246
Module for reading and writing control unit Denso installed on diesel vehicles with engines Mazda SkyActiv-D.
Mazda Diesel Denso Gen3 SH72543 (FID: 246)
The control unit is powered by a processor Renesas SH72543 with internal flash memory ..
$239.73
Set of 8 modules 1,2,3,4,5,6 Petrol Toyota Denso, Toyota Denso Toyota Denso OLD and Petrol Turbo. Allows you to edit all available petrol cars are Toyota, Lexus, Scion on the units of DENSO. 10% savings when ordering.
10% savings when ordering.
..
$2 049.70
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
Supports reading and writing c Mazda gasoline engines the Sky Active 2.0 2.5, on which are installed an ECU manufactured by Mitsubishi.
..
$66.45
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
Features of the module:
Write firmware
Read/Delete errors
Virtual reading
Check/Fix the checksum (the bypass digital signature)
Tabs:
CAN - for Master ECU
Slave To record a second engine ECU (Slave)
Stock - to return to the flow without using th..
$132.89
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.87
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
$359.60
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
The module is designed for Chip tuning Mazda 2019 model year, are equipped with ECU Denso by Frima {PYFB} Mitsubishi {PYFA} and engines 1.5 L, 2.0 L, 2.5 L, 2.5 T
List of cars:
Car Mazda CX-3 DK 2019 Denso OBD 78
Car Mazda CX-5 KF 2019 Mitsubishi OBD 78
..
$93.03
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
Supports reading Full Flash and recording of calibrations petrol cars Suzuki, ECU manufactured by Hitachi c CPU SH7058. Recalculation of the CRC. Read & clear error ECU internal combustion engine.
Suzuki Escudo 2.7 L Suzuki Grand Vitara 2.7 L
..
$66.45
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
