Great Wall/Lifan ME17 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.6L/2.0L D4G15/E4G16/SQR484 (ME17.8.8) [RD/WR/CK]
Chery 2.0L D4G20 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.5T/2.0T E4G15C/E4T15C/D4T20 (ME17U6) [RD/WR/CK]
Chery 1.6T F4J16 (MED17.8.10) [RD/WR..
$159.47
Set of modules (General license):
Continental DC4 TCM
Continental TA2005 TCM
The modules are designed to read / write calibrations and programs of the DC4/TA2005 TCM ECU installed on Renault vehicles via the diagnostic connector.
Additional function:
Cal..
$66.45
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.45
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.45
License 63, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
NEC + 24C64 06/2010+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64 06/2012+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64..
$199.34
License 06, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
Skoda Fabia 2011 (P/N 5J0920810E) Reading/KM Recording, Reading/Write EEPROM, Read Pin
Skoda Octavia A5 2009 (P/N 1Z0920803B) Reading/KM Recording, Reading/Write EEP..
$106.32
It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the..
$93.03
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
Designed to read and record the calibration and program the ECU SID208 vehicle Peugeot Boxer/Citroen Jumper via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identifica..
$132.89
The module is designed for reading and writing ECU MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90, installed on BMW cars.
Work with the ECU is performed on the table without opening the ECU. Identification and error reading/reset functions..
$199.34
Designed to read/write calibration and program the ECU Delphi DCM6.2/6.2A/6.2C installed on the Peugeot/Citroen via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identi..
$93.03
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.79
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
$132.89
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.34
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.60
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E78.
Examples of vehicles equipped with this type of ECU: Opel Astra J A14NET, A14NET Opel Opel Corsa C, Opel Mocca A14NET, A14NET Chevrolet Cruze, Chevrolet Tracker A18XER, Chevrolet Malibu A..
$132.89
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.73
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.80
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
License 49, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
..
$132.89
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$199.34
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
Attention! This module works in conjunction with CombiLoader 2.16 or later.
The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector.
The module automatically corrects CS calibrati..
$66.45
The module is designed for reading and writing software and calibrations of the Delphi DCM 6.2V ECU of VAG group cars via UDP protocol via the diagnostic connector.
The module automatically corrects CS calibrations during recording.
The module supports the "Virtual r..
$132.89
The modules are designed for reading and writing the SIMOS12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECU installed on VAG vehicles.
Work with the SIMOS12.1/12.2 ECU is performed on the table without opening the ECU.
Работа с ЭБУ SIMOS16.11 is performed on the table with the ECU openin
..
$199.34
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.80
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
1.5L dCi Delphi DCM 1.2 (ST10/512KB) [RD/WR/CK]
1.5L dCi Delphi DCM 3.4 (SH7059/1536KB) [RD/WR/CK]
1.5L dCi SID 301/303/304 (MPC562/2MB) [RD/WR/CK]
1.5L dCi SID 305/306 (TC1766/1504KB) [RD/WR/CK]
1.5L dCi SID 307 (TC1767/2MB) [RD/WR/CK]
2.3L dCi SID 309 (TC1767/2..
$93.03
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allows you to change the VIN code in the downloaded firmware.
..
$66.45
Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71.
Available the following cards:
The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficien..
$239.73
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.80
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.80
The set of modules (General license):
Delphi DCM3.7 SsangYong
Delphi DCM3.7 GM
Delphi DCM3.7 GreatWall
Delphi DCM3.7 Hyundai/Kia
Delphi DCM3.7 VAG
The modules are designed to read / write FLASH memory of ECU Delphi DCM3.7, mounted on SsangYong, Opel, Chevrole..
$132.89
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
The price shown is for the owners of the Sirius module 3x
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allo..
$26.58
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.60
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
$239.73
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
The module is designed for chip tuning of Ford Focus 2.0, Maverick 3.0, Escape 2.3, Escape 3.0, Mazda Tribute 2.3 cars equipped with Visteon EEC-V ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (A. Teslya).
A Limite..
$106.32
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.79
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector.
ECU Continental EMS3155 ustanavlivaetsya on engines 1.2 T.
ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L.
ECU Bosch EDC17C84 i..
$132.89
The module is designed for chip tuning of VAG cars (Skoda, Audi) with 1.0TFSI and 1.4TFSI engines equipped with Bosch MED17.1.27. Please note: Third-party developer module! Technical support from the module author (KHN09). Firmware for Bosch ME17 controllers is saved by default in SMS-Soft Contai..
$159.47
The module is designed for chip tuning of VAG cars equipped with Bosch MED17.5.20 with 1.4 TFSI engines.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in..
$159.47
The module allows chip tuning of Opel, Chevrolet, Cadillac cars equipped with an ACDelco E37 ECU.
Examples of cars equipped with this type of ECU: Chevrolet Captiva (C140) 2011+, Opel Antara 2011+.
Pay attention:
A third-party developer module! Technical support from th..
$13.29
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.89
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
The module is designed for chip tuning Hyundai Santa Fe, Hyundai Tucson, KIA Carnival, KIA Sorento Prime, KIA Sportage diesel engines 2.0 CRDi and 2.2 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmw..
$106.32
The module is designed for chip-tuning of cars of the VAG group (Audi A3/A4/A5/A6/Q3/Q5/TT, Skoda Superb, VW Golf, VW Passat, VW Tiguan, etc.) with a diesel engine capacity of 2.0 L, EDC17C46 Bosch ECU.
Please note:
Third-party module developer! Technical support from the a..
$132.89
The module is designed for chip tuning Hyundai(I30, I40, IX35, Santa Fe) and Kia(CEE'd, Optima, Soul, Sportage, Venga) with diesel engines 1.6 CRDi, 2.0 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Fir..
$106.32
The module is designed for chip-tuning diesel cars fitted with Continental SID807:
Citroen C3 1600 HDi
Citroen C3 Picasso 1600 HDi
Citroen C4 1600 HDi
Citroen C4 Grand Picasso 1600 HDi
Citroen C5 1600 HDi
Citroen DS3 HDi 1600
Citroen DS4 HDi 1600
..
$132.89
The module is designed for chip-tuning VAG group (VW Amarok, VW Crafter, VW LT) with a diesel engine capacity of 2.0 L, ECU Bosch EDC17C54.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC..
$132.89
The module is designed for chip-tuning of automobiles in China, equipped with Bosch MED17.8.10, for example, Geely Atlas 1.8 T.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored ..
$159.47
The module is designed for chip-tuning VAG group diesel engine 3.0 L ECU Bosch EDC17CP44.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are stored by default in the format of SMS-Soft..
$132.89
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
License 68, may be applicable at the discretion of the licensee (user) to the work:
1. Auto-search Mode:
Reading the mileage of HYUNDAI / KIA cars by OBDII with the MED17/EDC17 ECU.
Automatic search for the specified mileage in the EEPROM dump loaded into the program...
$106.32
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.45
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.32
New ECU M86 applies to cars UAZ Pro. Manufacturer software hardware — NPP ITELMA.
This module allows you to produce professional chip tuning UAZ Pro equipped ECU M86 with ITELMA. Edited more than 950 calibration management system M86, which allows full professional chip tuning UAZ...
$106.32
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.32
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
License 85, may be applicable at the discretion of the licensee (user) to the work:
Correction of mileage readings with recalculation of checksums in the read EEPROM area of the processor firmware,
in DSG DQ200, DSG DQ200_MQB, DSG DQ200 G2, DSG DQ250 E/F(02E) units installed on..
$79.74
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
The module is designed to edit the data of the registrar of the VAZ 74.8 and M74.9 blocks with NPO Itelma. The module monitors the integrity of the data when opening and recalculates all the necessary CS when saving. An EEPROM (4 kilobytes) is used for editing.
..
$26.58
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
The module allows you to view, edit, compare the firmware files of Kamaz, JAC, Foton cars with a Cummins 3.8L engine with a Continental CM2220 control unit. It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader. The module contains more than 1000..
$398.68
Module supported:
Read/erase error codes
Verification and recalculation of the checksum (CS)
Identification
Entry
Reading
For the following ECU's:
BRZ SH72531 [1280k] CAN 2013+
SH7058 [1024k] CAN 2007+
SH7058 [1024k] K-line 2003+
SH7..
$106.32
The module allows you to view, compare and edit the firmware files of MAN c ECU EDC17CV42 cars.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error mask are available for editing. The modu..
$664.47
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.80
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
The module allows you to view, edit, compare the firmware files of Foton, JAC cars with Cummins engine with the Continental CM2880 control unit.
It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader.
The module contains more than 1000 b..
$332.24
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.68
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.73
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
FID: 280
Module for reading and writing by CANbus Isuzu diesel vehicles with Transtron ECUs based on Renesas SH7058, SH7059, SH72533 and SH72544.
Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)
Family for Transtron ECUs based on MCUs Renesas SH7058/SH7059/..
$179.80
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.05
FID: 337
A module for reading and writing Shindengen control units installed on Honda motorcycles.
Honda Moto Shindengen V850/RH850 K-Line (FID:337)
Sihndengen engine control units are powered by Renesas V850/RH 850 series processors with 256/384Kb internal flash memo..
$247.15
Reading calibrations
Recording calibrations
Reading/erasing errors
Recalculation of CS
..
$106.32
Reading calibrations
Recording calibrations
Reading/erasing errors
Recalculation of CS
..
$93.03
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$492.48
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
