Daewoo Gentra (Delphi MT60), Chevrolet Aveo, Chevrolet Cruze (Delphi MT80), Chevrolet Cruze, Daewoo Lacetti (Siemens SIMTEC76). Designed for read-write FLASH memory of ECUS via diagnostic connector.
..
$66.45
The modules operate only in conjunction with the base module Delphi MT60/MT80 and designed for read-write full image of ECU Delphi MT60/MT80 diagnostic method using the J2534 interface.
..
$93.03
The set of modules (General license):
EDC17C11 Renault Bosch J2534
EDC17C42 Renault Bosch J2534
SID301 Renault J2534
SID305/306 Renault J2534
SID307 Renault J2534
Delphi DCM3.4 Renault J2534
The modules are designed to read/write and(or) field calibrati..
$106.32
Modules allow you to produce a chip tuning (reading and writing FLASH) ECU Delphi MT34, Delphi MT80 and Delphi MT92 vehicle Great Wall/Haval/Geely, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$106.32
The module allows for chip tuning cars Daewoo Gentra, equipped with ECU Delphi MT60.
..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
The set of modules (General license):
Delphi DCM3.7 SsangYong
Delphi DCM3.7 GM
Delphi DCM3.7 GreatWall
Delphi DCM3.7 Hyundai/Kia
Delphi DCM3.7 VAG
The modules are designed to read / write FLASH memory of ECU Delphi DCM3.7, mounted on SsangYong, Opel, Chevrole..
$132.89
Designed for chip-tuning ECU Delphi and Delphi MT05 MT05.2, installed in various types of motorcycles.
Control units Delphi MT05, and MT05.2 differ by the type of processor and size of FLASH memory. For Delphi MT05 FLASH size is 128kB, for Delphi MT05.2 — 256Kb. The type of ECU is determined ..
$106.32
The cars of Chinese production (Great Wall Hover, BYD, etc.) with Delphi MT20U ECU, MT20U2, MT20UED, MT22U and MT22.1. Supported read and write FLASH and EEPROM.
..
$93.03
Designed to read/write calibration and program the ECU Delphi DCM6.2/6.2A/6.2C installed on the Peugeot/Citroen via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identi..
$93.03
Module ACDelco Delphi intended read / write FLASH memory of ECU Delphi ACDelco E37/E38/E39/E67/E78/E83 installed on Chevrolet and Opel via the diagnostic connector.
Table of applicability ACDelco E37 (2.4 L — LE5/LE9):
Chevrolet Captiva (C140) 2011+
Opel Antara 2011+
..
$119.61
The module is designed for reading and writing software and calibrations of the Delphi DCM 6.2V ECU of VAG group cars via UDP protocol via the diagnostic connector.
The module automatically corrects CS calibrations during recording.
The module supports the "Virtual r..
$132.89
It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the..
$93.03
License 40, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of the calibration area (with recalculation of checksums)
..
$106.32
Chevrolet (Lacetti, Epica, Tacuma, Rezzo, Spark) and Daewoo.
..
$166.12
The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector.
Table of applicability ECU SIMTEC 70:
Opel Astra G (1998-2000) X18XE1/X20XEV
Opel Vectra B (1998-2001) X18XE1/X20XEV
Opel Zafira (..
$119.61
The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recording.
..
$199.34
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
The price shown is for the owners of the Sirius module 3x
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allo..
$26.58
The modules are designed to read / write FLASH Chevrolet/Opel/Cadillac/SAAB, equipped with ECU Bosch ME9.x and the Bosch ME7.9.9 via the diagnostic connector.
Work with the J2534 adapter, sold separately. Module is a Bosch ME9.x GM makes automatic recalculation of the COP recorded calibration..
$53.16
The modules are designed for reading and writing the SIMOS12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECU installed on VAG vehicles.
Work with the SIMOS12.1/12.2 ECU is performed on the table without opening the ECU.
Работа с ЭБУ SIMOS16.11 is performed on the table with the ECU openin
..
$199.34
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.89
Kit modules:
Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector.
Isuzu Transtron ..
$106.32
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.3 and MT22.5.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$119.61
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU p..
$119.61
The module is designed for chip tuning of Ssang Yong Actyon, Korando, Rexton, Rodius, Stavic, etc. cars with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulik..
$132.89
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$66.45
Module allow to make the chip tuning Hyundai/Kia with engines V6 2.7/3.3/3.8 L, equipped with ECU Delphi MT38.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delphi MT38 by means of the loader CombiL..
$132.89
The module is designed for chip tuning of Hyundai Starex, Porter, HD78, i30, KIA Bongo and others cars with 2.5CRDI diesel engines, Delphi DCM 3.7 ECU.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
Supported software versions:..
$132.89
Module allow to make the chip tuning Hyundai Genesis/Equus, Kia Cadenza/Quoris/Sorento Prime engines 3.3/3.8/5.0 l, equipped with ECU Delphi MT86.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delph..
$132.89
The module is designed for chip tuning of Great Wall Hover cars and others with 2.0 TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported software versions:
&..
$106.32
The module is designed for chip tuning of Chevrolet Captiva, Cruze, Orlando, Daewoo Winstorm, Opel Antara, etc. with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kuli..
$132.89
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$26.58
ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong.
Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle.
Works through the J2534 interface.
ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato..
$93.03
The kit contains modules:
Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L.
Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particu..
$66.45
The Valeo V4X module is designed to read and write the FLASH memory of the Valeo S3000/V40/V42 ECU installed on Renault cars through the diagnostic connector.
The Sagem S3K module is designed to read and write calibrations and the program of the Sagem S3000 ECU (512k FLASH) install..
$66.45
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.45
The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recordin..
$265.79
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allows you to change the VIN code in the downloaded firmware.
..
$66.45
For chip-tuning Chevrolet.
..
$132.89
For chip-tuning of cars of Chinese production (Great Wall Hover, Great Wall Safe, BYD F3, Chery Tiggo, etc.).
..
$93.03
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
For chip-tuning Chevrolet and Geely Emgrand.
..
$79.74
The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles.
Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available.
..
$199.34
It is designed for reading and writing software/calibrations of the SID605/WISE13H/WISE15/MD1/EQ EDC17 V6/V7 ECU installed on MAZ cars and Chinese-made cars via a diagnostic connector.
The kit supports the following types of ECU:
SID605: software/calibration recording.
..
$265.79
Kia, Hyundai, equipped with ECU Bosch M(G)7.9.8. Designed for recording FLASH memory ECU Bosch M7.9.8 and MG7.9.8 via the diagnostic connector without removing the ECU from the vehicle.
..
$93.03
Designed for read-write FLASH memory of ECU Cummins CM2150/2220/2880/2350 mounted on GAZ/MAZ/KAMAZ etc. via the diagnostic connector.
..
$199.34
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$79.74
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$199.34
The module is designed for reading and writing ECU MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90, installed on BMW cars.
Work with the ECU is performed on the table without opening the ECU. Identification and error reading/reset functions..
$199.34
The module is intended for recording and(or) region calibration ECU Siemens EMS2204, installable in particular on cars Ford Focus 3 engine 1.6 l
..
$66.45
The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$132.89
For chip-tuning of cars of Chinese production (Great Wall Hover, Great Wall Safe, BYD F3, Chery Tiggo, etc.).
..
$93.03
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.45
The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles.
Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors.
..
$132.89
Cars Renault Logan 2, Sandero 2, Fluence, Megane 3, Latitude, Duster.. Designed to read and record the calibration and program the ECU mounted on Renault cars via diagnostic connector.
..
$66.45
The module is designed to work with ECU Delphi MT38, Delphi MT86, supported reading (where possible), recording, checking and correction checksums. MT38 available for work in BSL mode.
2.7L, 3.3L, 3.8L (MT38/CAN) [WR/CK]
2.7L, 3.3L (MT38/K-Line) [RD/WR/CK]
2.7L, 3.3..
$93.03
The module is designed to work through the diagnostic connector of a car with Delphi DCM6.2 engine control units used in VAG concern cars. Virtual reading, writing, checking and correction of checksums are supported.
1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/RD/WR/CK]
..
$132.89
Module GM MT60/MT80 Extended - OBD2 is designed to read and write full dump of the internal FLASH and EEPROM memory of ECU MT60/MT80 manufactured by GM. The module can be used to cloning units.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lit..
$84.82
The modules are designed to read / write the FLASH/EEPROM of the ECU series Bosch EDC7/EDC16/PSG16/ME9 without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
The module does not s..
$199.34
Designed to read and record the calibration and program the ECU SID208 vehicle Peugeot Boxer/Citroen Jumper via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identifica..
$132.89
The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector.
Module is the automatic correction of the COP calibration during the recording.
Work with the J2534 adapter, sold separately.
..
$66.45
The module is designed to work with the ECU built on microcontrollers SH72513/SH72543/SH72544 installed on diesel vehicles of different brands. Supported read, write, and recalculation of checksums.
Kia/Hyundai 2.5 L CRDI (DCM3.7AP) [RD/WR/CK]
Opel/Chevrolet 2.0 L, 2.2 L CDTI (DCM3...
$132.89
License 89, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by Delphi.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading/EEPROM Wri..
$106.32
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.87
Module Delphi MT20U/MT38/MT20U2/MT22U-OBDII (cars Chery, BYD, Hoover, Lifan, Kia, Hyundai)
..
$70.27
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$39.87
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.32
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
License 26, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash or EEPROM file, depending on the type of ECU.
Works as an edit..
$106.32
Module Simtec 76/Delphi MT60/MT80 - OBD2 (Chevrolet)
..
$56.73
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.32
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
The modules are designed to read / write ECU Continental SIM2K-250/251/253/260/261 that are installed on vehicles Hyundai/Kia.
No need to opening the ECU. In diagnostic mode the available functions of identification, read/clear faults and recording and/or calibrations.
The mo..
$132.89
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.89
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.80
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
$239.73
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$66.45
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$39.87
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
$359.60
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.81
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$66.45
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
$239.73
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.73
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
$359.60
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.61
Module Delphi HV240/MR140-OBDII (Chevrolet Aveo, Lacetti)
..
$70.27
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.18
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
$239.73
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.45
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$239.21
1.5L dCi Delphi DCM 1.2 (ST10/512KB) [RD/WR/CK]
1.5L dCi Delphi DCM 3.4 (SH7059/1536KB) [RD/WR/CK]
1.5L dCi SID 301/303/304 (MPC562/2MB) [RD/WR/CK]
1.5L dCi SID 305/306 (TC1766/1504KB) [RD/WR/CK]
1.5L dCi SID 307 (TC1767/2MB) [RD/WR/CK]
2.3L dCi SID 309 (TC1767/2..
$93.03
Reading calibrations
Recording calibrations
Reading/erasing errors
Recalculation of CS
..
$106.32
Module is designed to work with the ECU of 2.0L Delphi DCM6.2A/DCM6.2C diesel engines installed on PSA group cars, working through a diagnostic connector. Supports reading, writing, checking and correcting checksums:
Citroen/Peugeot 2.0L HDi (DCM6.2A) [RD/WR/CK]
Citroen/Peugeot 2.0L..
$93.03
The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices.
The modules support the following types of ECUS:
MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB.
MagnetiMarelli MM7GV:..
$66.45
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.45
The module is designed to work in service mode with the ECU ME9/MED9/EDC16. It supports reading and writing the built-in flash memory of the MPC556/MPC562/MPC564 microcontrollers, external flash memory and EEPROM, as well as checking and correcting CS and RSA signatures (except for the MED9 VAG E..
$239.21
The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector.
Is free app for all users 2 or 3 version of module BSL TC17xx J2534.
Module Bosch MEDC17 Hyundai/Kia supported the following types of EC..
$106.32
Great Wall/Lifan ME17 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.6L/2.0L D4G15/E4G16/SQR484 (ME17.8.8) [RD/WR/CK]
Chery 2.0L D4G20 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.5T/2.0T E4G15C/E4T15C/D4T20 (ME17U6) [RD/WR/CK]
Chery 1.6T F4J16 (MED17.8.10) [RD/WR..
$159.47
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$212.63
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.89
License 32, may be applicable at the discretion of the licensee (user) to the work:
Chery Kimo Read/Write EEPROM, Read/Write KM (Adapter J2534)
Chery Amulet Read/Write EEPROM, Read/Write KM(KLine)
Chery Tiggo ver 1 Read/Write EEPROM, Read/Write KM(KLine)
Chery Fora Read/..
$66.45
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
The module is designed to read / write calibration and program control UNIT Siemens SIM2K-243 GM vehicle Chevrolet Spark M-300.
The module allows reading and writing of programs or the field of calibrations, diagnostic method, without removing the ECU from the vehicle.
Works through the J..
$66.45
The car 'Lada Vesta/XRay/Largus' with electronic gas pedal, equipped with ECU M86/M74M.
The module is intended for read-write FLASH/EEPROM ECU М86 with a production of vases, based on the Infineon processor family XC27x5 via the built-in BootStrapLoader, and recording via the d..
$66.45
The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector.
Module is the automatic correction of the COP calibration during the recording.
Work with the J2534 adapter, sold separately.
..
$66.45
License 02, may be applicable at the discretion of the licensee (user) to the work:
Continental SID 305 Reading/KM record
Continental SID 306 Reading/KM record
Continental SID 307 Reading/KM record
Continental SID 309 Reading/KM record
Delphi DCM3.4 Reading/KM reco..
$106.32
Module kit:
The module is designed to read/write FLASH memory of DSI TCM ECUs installed on SsangYong/Geely vehicles via the diagnostic connector. The module performs automatic correction of the COP of calibrations during recording.
The module is designed to write software / calibrat..
$93.03
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$119.61
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
This module allows you to work on the car via the OBDII connector with the Visteon ECU installed on Ford cars.
Module Functions:
Identification Reading
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalculation of calibration area c..
$66.45
This module allows you to work on a car via an OBDII connector with Siemens ECM installed on Ford cars.
OBD II Mode (working on a car or on a desk):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalcula..
$66.45
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$119.61
License 10, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the EEPROM file.
Works as an editor.
List of supported ECUs:
..
$132.89
License 21, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$106.32
Distribution of activation files after 01.06.2023
License 118, may be applicable at the discretion of the licensee (user) to work:
with a Bosch electric power steering on the Nec V850 70F3187 + EEPROM 95080 MK on the table or via the OBDII connector (where there is a technical ..
$66.45
Attention! This module works in conjunction with CombiLoader 2.16 or later.
The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector.
The module automatically corrects CS calibrati..
$66.45
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
TC1762/TC1766 MICRO (1504KB)
TC1762/TC1766 EEPROM (32KB)
TC1792/TC1796 MICRO (2048KB)
TC1796 MICRO+EXT (4096KB/6144KB)
TC1796 EXT (2048KB/4096KB)
TC1792 EEPROM (64KB)
TC1796 EEPROM (128KB)
TC1736 MICRO (1024KB)
TC1736 EEPROM (32KB)
TC1738/..
$239.21
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$106.32
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.34
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
The module is designed to read and write FLASH memory of ECU MT86 installed on a KIA/Hyundai. Working with these types of ECU's is via the J2534 device
ECU MT86 is a read only field calibrations. Recording is supported for the following formats:
Firmware reads th..
$42.41
License 75, may be applicable at the discretion of the licensee (user) to the work:
Reading/FullFlash Entry
Reading/EEPROM recording
The ability not to overwrite the boot sector.
The module allows you to use your Seed Key, in case it was replaced with a non-s..
$106.32
License 76, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording of the Flash memory of the ECU of the transmission of VAZ cars through the diagnostic connector or on the table (connection is available in the online help).
..
$66.45
Module 'China MT80 ECU - OBDII' is designed to read and write FLASH memory of ECU MT80 installed on Chinese vehicles through J2534 device and KLine adapter.
Supported the conversion and checksum. Recording is performed only in the area of calibrations.
For holders of CHIPSOFT J..
$93.09
Module GM SIM2K-243 - OBD2 is designed to read and write FLASH memory of ECU SIM2K-243 installed in the cars of GM via the J2534 device.
Supported the conversion and checksum field calibrations.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. ..
$68.54
Module EMS3120 (VAZ/Logan) - OBD2 is designed to read and write FLASH memory of ECU Siemens EMS3120 fitted to cars VAZ, Logan via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Speci..
$63.61
The module is designed to read and write FLASH memory of ECU frame-mounted Mazda (2003-2013 year of release) via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 ( Lite) (Mid) adapter, a 50% discount on the module. Specify when o..
$93.09
The unit Valeo V40/V42 - OBDII is designed to read and write FLASH memory of ECU Valeo V40/V42 Renault cars.
The module must J2534 device.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Specify when ordering the serial number of your adapter and appl..
$45.25
Module OPEL ECU - OBD2 includes work with the ECU Simtec-71.5, Simtec-71.6, Simtec-75.1, 75.5 Simtec, Simtec 81.1, Delphi MT35E, Bosch ME9.1 / ACDelco E77 (read and write FLASH memory). Supports data only ECU on the CAN bus.
..
$56.62
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
Module 'VW Polo ECU - OBDII' is designed to read and write FLASH memory of ECU Magnetti Marelli 7GV, 7GVE, 4HV, installed on the cars of VW via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% disco..
$88.17
Module EDC17/MED(G)17 (Kia/Hyundai) - OBD2 is designed to write FLASH memory of ECU Bosch EDC17C08, Bosch, EDC17CP14, Bosch MED(G)17.9.8 via the J2534 device.
Please note that this module can only record the previously prepared serial tuning or firmware!
..
$28.33
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
License 99, may be applicable at the discretion of the licensee (user) to the work:
1. OBDII Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculation of checksums)
..
$106.32
CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary f..
$99.67
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
This module is designed to read / write FLASH and EEPROM memory of ECU M74 in boot mode . Working with this type of ECU is performed via K-Line adapter for the ECU M74 and through the J2534 device to the ECU M74CAN.
The ECU is mounted on the automobiles.
For significant acceleration of th..
$23.41
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.73
Module Ford ECU Siemens SIM28/SIM29/SIM210/SIM22 / EMS2204 / SID206, Visteon ESU-131/411/412/415/418 - OBD2 is designed to read and write FLASH memory of ECU Siemens SIM28, SIM29, SIM210, SIM22, EMS2204, SID206, Visteon ESU-131/411/412/415/418 - OBDII Ford vehicles.
The mod..
$48.98
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
Module 'Denso SH7058 ECU - OBDII' is designed to read and write FLASH memory of ECU Denso SH7058 processor fitted to cars Suzuki, Mitsubishi, Volvo, and others circa 2007 - 2010 model years. Please note that only supports Denso ECUS in which the manufacturer laid the engineering way of working wi..
$113.19
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.68
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.81
Supports reading and writing of the Mazda c CPU SH7055 7058 and via J2534 interface ( only Tested with the Open port 2.0) by OBD2. Supported ECU Denso and Mitsubishi Corp. Latest restored from any state.
..
$79.74
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
MDflasher software for odometer adjusting, to work with the immobilizer, the Airbag, and als..
$39.87
Designed for chip tuning of MAZ cars with installed WISE15 ECU (WEICHAI). To work with the WISE15 ECU, you need a 24V J2534 adapter and a CAN2CAN adapter.
..
$132.89
A special adapter to connect the control units on the table.
Performs automatic power management, and boot pins through the J2534 adapter.*
Required to read in the BSL mode for control units Bosch M7.8/ME7.8.8 and Continental SIM2K-25x/26x
* - tested and guaranteed works wi..
$53.16
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.22
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
$299.66
The kit includes the modules:
28 Module Ford EMS2204;
27 Module-Ford Bosch MED17.2;
22 Module, Ford, Siemens VDO EMS2102 and EMS2101;
21 Module Ford Diesel SID206;
19 Module Ford SIM210, SIM22;
15 Module-Ford Bosch ME 9.0 Petrol (Turbo);
14 Module Ford Diesel Delphi DC..
$265.79
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.34
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
BitBox is an evolving software package that allows to identify, read and write the internal ..
$46.96
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.73
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
Module Bosch ME17.9.11/12-OBD2 is designed to write FLASH memory of ECU Bosch ME17.9.11, Bosch ME17.9.12 via the J2534 device. Please note that this module can record only serial firmware!
..
$11.71
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
A set of their 5 modules discount for Toyota cars.
The kit includes:
Denso Toyota Gen1 CAN
Toyota Denso Gen2/newGen CAN
Toyota Denso Gen3 CAN
Toyota Delphi Gen1 CAN
Toyota Gen1 Virtual Reader
..
$1 018.86
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
To operate the module requires the adapter Ford/Mazda VCM2 or Scanmatik-2 PRO
Mondeo 3 1.8L, 2.0L, 2.5L, 3.0L Duratec HE (LEVANTA) [RD/WR/CK]
EEC-V 216K (EEC-V) [RD/WR/CK]
3.0L, 4.0L, 4.6L Duratec V6/V8 (PCM150) [RD/WR/CK]
1.8L, 2.0L, 2.2L Duratorq TDCi (Visteon) [RD/WR]..
$93.03
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.73
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.36
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.89
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days.
MMC Flasher universal Downloader intended for chip tuning Hyundai, Kia, Mitsubishi, Mazda, Nissan, Honda, Subaru..
$30.57
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
$239.73
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.59
The module is designed for diagnostics of EDC17CV44/54 CAN
..
$106.32
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.73
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.88
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
![[52] Delphi MT38 - OBD2 - BOOT](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[52] Delphi MT38 - OBD2 - BOOT")
