Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
$143.93
Allows you to edit and compare the error mask on a large number (about 1000) of Denso software. The module allows you not only to turn off, but to turn back the DTC error code.
Supported Software:
89663-01032- 89663-01121- 89663-02023- 89663-02161- 89663-02162- 89663..
$39.82
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.73
The Bosch EDC7UC31 GAZ module is designed for chip tuning of GAZ and MAZ cars with YAMZ-5344.20, YAMZ-53416, YAMZ-53441.20, YAMZ-53442, YAMZ-536, YAMZ-53601, YAMZ-53602, YAMZ-53603, YAMZ-53613, YAMZ-53622, YAMZ-53623, YAMZ-53624, MMZ-245 diesel engines.7.
Supported firmware (softwa..
$265.46
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$238.91
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.73
The module is designed to work with the ECU Kefico/Denso processor SH72546 installed in cars with a diesel engine of 2.5 l, standards of toxicity Euro-6. Supported read, write, review, and correction checksums.
Kia/Hyundai 2.5L CRDI (SH72546) [RD/WR/CK]
Hyundai Euro 5 (Denso SH7058S..
$92.91
The module is designed to work with ECU Delphi MT38, Delphi MT86, supported reading (where possible), recording, checking and correction checksums. MT38 available for work in BSL mode.
2.7L, 3.3L, 3.8L (MT38/CAN) [WR/CK]
2.7L, 3.3L (MT38/K-Line) [RD/WR/CK]
2.7L, 3.3..
$92.91
The module is designed to work with the ECU built on microcontrollers SH72513/SH72543/SH72544 installed on diesel vehicles of different brands. Supported read, write, and recalculation of checksums.
Kia/Hyundai 2.5 L CRDI (DCM3.7AP) [RD/WR/CK]
Opel/Chevrolet 2.0 L, 2.2 L CDTI (DCM3...
$132.73
DQ200 (0AM) [VR/WR/CK]
DQ200MQB/G2 (0CW) [RD/VR/WR/CK]
DQ250C (02E) [RD/VR/WR/CK]
DQ250E/F (02E) [VR/WR/CK]
DQ250MQB (0D9) [RD/VR/WR/CK]
DQ400 (0DD) [RD/WR/CK]
DQ500 (0BH/0BT) [RD/WR/CK]
VL300/V30 (01J/0AN) [VR/WR/CK]
VL381/..
$265.46
The module is designed to work with the ECU EMS3155, SID309, Hitachi CPU RH850 working on the UDS Protocol and installed in vehicles with petrol engines 1.2 l and diesel 1.5 l Supported read, write, review, and correction checksums.
1.2 T EMS3155 UDS (TC1782/2.5 MB) [RD/WR/CK]
1.5 L..
$132.73
The module is designed to work with ECUS that are installed in vehicles with Ford diesel engines 1.4, 1.5, 1.6 l Supported read, write, review, and correction checksums.
Ford Focus 3: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
Ford Mondeo 4: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
..
$92.91
Great Wall/Lifan ME17 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.6L/2.0L D4G15/E4G16/SQR484 (ME17.8.8) [RD/WR/CK]
Chery 2.0L D4G20 (ME17.8.8) [RD/WR/CK]
Chery 1.5L/1.5T/2.0T E4G15C/E4T15C/D4T20 (ME17U6) [RD/WR/CK]
Chery 1.6T F4J16 (MED17.8.10) [RD/WR..
$159.27
The module is designed to work with the ECU from diesel engines 1.6, 2.0, 3.0 and 4.2 TDI are installed on passenger cars and crossover vehicles group VAG, approximately 2010. Supported entry, verification and correction of the COP.
2.0L, 3.0L TDI (EDC17CP04/EDC17CP14/EDC17CP..
$119.46
The module is designed to work with ECU Simos 8.1, 8.2, 8.3, 8.4, 8.5, 8.6, 10, 11, 12, PCR 2.1. Supported reading (read or virtual), the entry (with or without unlocking), verification and correction of the COP.
2.8 L V6 FSI (SIMOS8.1) [RD/WR/CK]
3.2 L V6 FSI (SIMOS8.2) [RD/WR..
$159.27
TC1762/TC1766 MICRO (1504KB)
TC1762/TC1766 EEPROM (32KB)
TC1792/TC1796 MICRO (2048KB)
TC1796 MICRO+EXT (4096KB/6144KB)
TC1796 EXT (2048KB/4096KB)
TC1792 EEPROM (64KB)
TC1796 EEPROM (128KB)
TC1736 MICRO (1024KB)
TC1736 EEPROM (32KB)
TC1738/..
$238.91
For programming ECU VS-5.6, you must use a special adapter, the cost of the adapter is included in the cost of the module. Required shipping of the adapter to the user.
The vehicles are equipped with ECU ITELMA VS-5.6.
..
$33.18
Toyota Denso Petrol 5.7i module for chip tuning of Toyota Sequoia, Tundra, Lexus LX570, etc. with 5.7-liter 3UR-FE and 3UR-FBE engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the authors of the module (V. Kulikova and A. Tesla).
..
$238.91
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.18
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.18
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.64
License 53, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to read and write a full memory image (FULL FLASH) for cloning the ECU.
List of supported ECUs:
Simtec 71.5
Simtec 71.6
Simtec 75.1
Si..
$106.18
License 59, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
D70F3230 -D70F3231 -D70F3232 -D70F3233 -D70F3234 -D70F3235 -D70F3236 -D70F3237 -D70F3238 -D70F3239 -D70F3333 -D70F3334-D70F333..
$66.36
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.36
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.18
License 58, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by CONTINENTAL.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 95..
$106.18
License 52, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Rec..
$132.73
License 50, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.64
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.73
The module for the new version of the program Chiploader NG
Module [51] Bosch MEDC17 - Bench is designed to read and write the internal memory (flash and eeprom) of the processor is Tricore ECU Bosch MEDC17 on the table without disassembling the ECU.
Detailed information ..
$258.17
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.25
Read/Write calibration by K line
Record calibration + program Can
Read/Delete errors
Check/Fix the checksum (fake digital signatures)
Supported units EDC16C39-5.41 and EDC16CP34-5.30
..
$66.36
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.40
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.75
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.65
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.97
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.46
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.92
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.37
The module is designed to work through the diagnostic connector of the car with transmission control units 6HP26, 5R/6R/6F/8F/10R of various modifications used in Ford cars. Supports reading, writing, checking and correcting checksums.
6HP26 TCM [RD/WR/CK]
5R110 TCM [RD/WR/CK]
..
$119.46
The module is designed to work with blocks EDC16C39, which are installed on vehicles UAZ Patriot, hunter with diesel engines ZMZ and Iveco. Supported reading calibrations (for Iveco), a record full of files (and calibration for the Iveco), verification and correction checksums.
Patriot/Hu..
$66.36
Basic kit:
GM ISFI-2S
VAZ, the first serial electronic control system on domestic cars.
January 4
VAZ, second serial electronic system of injection control, the domestic counterpart of ISFI-2S. Used since 1995
January-5.1.x
VAZ, a domestic ..
$66.36
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.94
The module supports the identification, reading and writing of calibration, reading and deleting faults, checksum recalculation.
..
$46.45
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
..
$19.91
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
..
$66.36
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
..
$66.36
Read/Write firmware
Read/Delete errors
Check/Fix the checksum (the bypass digital signature)
Virtual reading/Converting from dealer format (*.VBF)
..
$66.36
Read/Write firmware
Check/Recalculation of the checksum (to bypass the digital signature)
..
$66.36
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
..
$66.36
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055S/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7058/1MB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2007+ CAN-bus (SH7058S/1MB) [RD/..
$119.46
The module is designed for chip tuning of Hyundai and Kia cars with EURO-6 diesel engines equipped with Denso ECU with SH72543/SH72546 processors.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported s..
$265.46
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$238.91
The module is designed to work with the ECU EDC7/EDC16/EDC17 diesel engines Mitsubishi Fuso Canter. Supported read, write, review, and correction of the COP. For some cars with ECU EDC7/EDC16 for writing may require a direct connection to the connector block.
Fuso Canter (EDC7C4-6/EDC16C3..
$132.73
Updated version of programmer XPROG-M v5.55 is intended for programming of new microcontroller and memory chip manufacturers, Motorola, Infineon, Micronas, Texas, Atmel, ST, National(CR16), M35080 and immobilizer EWS-3, CAS4 5M48H including software is protected from reading.
Authorization th..
$97.89
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.46
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.64
FID: 238, 242, 245, 246
Module for reading and writing control unit Denso installed on diesel vehicles with engines Mazda SkyActiv-D.
Mazda Diesel Denso Gen3 SH72543 (FID: 246)
The control unit is powered by a processor Renesas SH72543 with internal flash memory ..
$239.88
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
$299.85
FID: 180, 181
Module to read and write via the diagnostic connector Ford control units Bosch MG1.
Ford Bosch MG1CS015 TC277 (FID: 180)
The family support units Ford Bosch MG1CS015 processor-based Infineon Aurix TC277 with internal memory of 4 MB.
Allows readi..
$239.88
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.73
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.88
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$39.82
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
$299.85
The Toyota Denso Diesel 3.0D (1KDFTV) module with 76F0040GD, 76F0039AGD, 76F0070, 76F0085 processors is designed for chip tuning of Toyota cars with 3.0L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the modul..
$238.91
PGM-FI Generic Read-Only [RD]
AT/CVT/DCT Generic Read-Only [RD]
PGM-FI (Keihin SH7058/1MB) [RD/WR/CK]
PGM-FI (Keihin SH72543/2MB) [RD/WR/CK]
PGM-FI (Keihin SH72546/3.75MB) [RD/WR/CK]
PGM-FI (Keihin MPC5566/3MB) [RD/WR/CK]
PGM-FI (Keihin TC1782/..
$199.09
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.88
Module to work through the diagnostic connector for Ethernet control units Bosch MG1 and MD1 mounted on the BMW F and G-series.
Supported units Bosch processor-based NXP MPC5777 with 7.5 Mb of internal flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)
BMW Fx..
$419.79
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.46
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.18
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.88
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.73
License 60, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
&..
$132.73
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.88
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.88
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, th..
$239.88
The module is designed to work with the ECU engine 1.0 TSI, 1.2 TSI, 1.4 TSI, 1.6 MPI, 2.0 TSI, 3.6 FSI, 1.0 MPI, etc. installed on vehicles group VAG (VW Golf 7, Polo, Passat B8, Skoda Rapid, Octavia A7, Tiguan, Jetta, Audi A1, A3, etc.). Supported entry, verification and correction of the COP.
..
$119.46
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.82
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.36
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.18
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.88
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.38
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$66.36
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.38
The module is designed for chip tuning of Citroen and Peugeot cars with 5GY (EP6FDTM), 5GZ (EP6FDT) engines equipped with Bosch MED17.4.4, for example, Peugeot 208 A9, Peugeot 308 T9, Peugeot 3008 T8, Citroen DS3 A55, Citroen DS5 B81, Citroen C4 Grand Picasso B78.
Pay attention:
..
$159.27
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
$119.94
License 06, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
Skoda Fabia 2011 (P/N 5J0920810E) Reading/KM Recording, Reading/Write EEPROM, Read Pin
Skoda Octavia A5 2009 (P/N 1Z0920803B) Reading/KM Recording, Reading/Write EEP..
$106.18
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.38
What is this system?
If You have several branches or regular customers that You make the firmware and they are interested in our product – they can get all the modules that You have, but they will not have access to the firmware, and You will keep the secret of your development. Th..
$299.85
The module allows you to produce professional chip tuning Lada X-Ray and Renault Duster/Kaptur, equipped with ECU Continental EMS3125.
Supports any version of calibration based on series RDE450, RDE540, RDE570.
Features of the module:
About 550 of calibration..
$106.18
The module is designed for chip-tuning diesel cars fitted with Continental SID807:
Citroen C3 1600 HDi
Citroen C3 Picasso 1600 HDi
Citroen C4 1600 HDi
Citroen C4 Grand Picasso 1600 HDi
Citroen C5 1600 HDi
Citroen DS3 HDi 1600
Citroen DS4 HDi 1600
..
$132.73
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
$239.88
Designed to work with Hitachi ECU (read full flash, write calibration, recalculation of the COP) with the SH705x CPUs installed on Nissan/Infiniti.
read Full cpu dump SH705x, SH7253x / Read Full Flash cpu SH705x, SH7253x
recalculation of the checksum / CRC
..
$159.27
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
$359.82
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.71
The module is designed to work with ECU Denso installed on vehicles JLR. Supported read, write, review, and correction checksums.
Jaguar XF/XJ/XK (X250/X350/X351/X150) 3.0L V6, 3.5L V8, 4.2L V8/SC (Denso) [RD/WR/CK]
Range Rover/Sport/Discovery 3 4.0L V6, 4.4L V8, 4.2L V8/SC (Denso) ..
$119.46
The module allows you to produce a professional chip tuning for Renault Logan and Renault Sandero 2 2 that equipped with ECU Continental EMS3120.
Supported IDs firmware module Logan/Sandero:
HW4319R_SW4234R_4541R
HW4319R_SW4234R_4928R
HW4319R_SW4234R_4929R
HW4319R_SW..
$106.18
The module is designed to read and write FLASH memory of ECU Siemens 5WP (Simos-7.1) via BootStrapLoader.
..
$29.82
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.73
The module is designed for operation with control units petrol engines and turbo diesel installed in vehicles Land Rover Freelander 2, Evoque, Discovery Sport etc. Supported read, write, calibration, validation and correction of the COP.
Discovery 3 2.7L TDV6 (SID201/SID204) [RD/WR/CK]
..
$159.27
Mazda: 1.6L Z6 AT (Mazda3 2004+) [RD/WR]
Mazda: 1.6L Z6 MT (Mazda3 2004+) [RD/WR]
Mazda: 1.3L ZJ (Mazda Demio 2003+) [RD/WR/CK]
Mazda: 1.8L, 2.0L, 2.3L L8/LF/L3 (Mazda3/6/CX7 2003+) [RD/WR/CK]
Mazda: 2.0L LF USA (Mazda3 -2009/1MB) [RD/WR/CK]
Mazda: 1.3L N3 (Mazda..
$92.91
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.91
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Panasonic processor Infineon Tricore TC197X with internal flash memory 4Mb.
..
$239.88
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.88
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.88
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.88
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.73
This module allows you to make chip-tuning of cars GAZ and UAZ vehicles that equipped with ECU Mikas-11, Mikas-11CR, Mikas-11ET, VS-8.
Supports the following versions:
The number of the ECU and firmware version of the ECU
824.3763.001-05 0789_101
821.3763.000-01 0..
$66.36
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.71
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.88
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
$239.88
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.88
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
$299.85
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
$239.88
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.88
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.88
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.88
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
$239.88
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.88
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.88
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.82
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
$239.88
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.88
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.88
The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb.
Currently it supports the following calibration: the ignition timing for h..
$239.88
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.88
The module allows you to adjust the transmission of Toyota, Lexus, in which the control program resides in a separate processor NEC 76F0040AGD.
We offer to edit the following settings of the transmission conditions for the transmission shift up and down, control pressure switch, overall oil p..
$599.71
Set of 15 modules Toyota Denso Diesel 1,2,3,4,5 + 1,2,3,4,5,6 Petrol + turbo Petrol + OLD + Gearbox+ GT86. Allows you to edit all the available vehicles Toyota, Lexus, Scion, Hino on the units of DENSO.
15% savings when ordering.
..
$3 772.15
Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering.
..
$3 238.41
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.85
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.88
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.82
The Valeo V4X module is designed to read and write the FLASH memory of the Valeo S3000/V40/V42 ECU installed on Renault cars through the diagnostic connector.
The Sagem S3K module is designed to read and write calibrations and the program of the Sagem S3000 ECU (512k FLASH) install..
$66.36
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.82
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.88
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.88
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
$239.88
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.76
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.76
Module for the calibration firmware and atmospheric turbocharged snowmobiles Arctic cat with power management Denso 32920-49Xxx processor-based Renesas SH7052.
..
$239.88
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.18
Machine 2004-2012 years with modules PCM150F, PCM170F (two versions), M799G - Escape, Explorer, Mustang, Mazda CX9, etc
Requires adapter enabled FEPS, for example: Scanmatik-2 PRO, MongooseJLR, Mongoose, Ford, Openport 2.0, Ford/Mazda VCM 1, VCM 2
Mazda6 3.0 L AJ 2003-2005 [RD/WR/CK]
..
$92.91
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
$359.82
Set of 5 modules 1,2,3,4,5 Toyota Denso Diesel. Allows you to edit all available diesel cars are Toyota, Lexus, Hino on the units of DENSO. 10% savings when ordering.
..
$1 403.31
A set of 7 modules to edit all available petrol cars Nissan and infiniti with the control units from Hitachi. 15% savings when ordering the kit.
The list of modules includes:
Nissan Hitachi Petrol Gen1 SH7054
Nissan Petrol Gen1 Hitachi SH7055
Nissan Hitachi Petrol Gen1 SH7..
$1 631.20
Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor.
Available the following cards:
Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure ..
$239.88
Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb.
Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture,..
$239.88
Set of 8 modules 1,2,3,4,5,6 Petrol Toyota Denso, Toyota Denso Toyota Denso OLD and Petrol Turbo. Allows you to edit all available petrol cars are Toyota, Lexus, Scion on the units of DENSO. 10% savings when ordering.
10% savings when ordering.
..
$2 050.99
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.82
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
$239.88
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.88
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.88
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.88
The Bosch MD1CS001 (DDE802L, DDE803S) BMW module is designed for chip tuning of BMW cars with B47D20xx diesel engines. Installed on:
3rd G20 Series
5th series G30 and G31
X3 Series G01
X4 Series G02
Pay attention:
A third-party developer module! Tech..
$331.82
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.88
Supports only the following Honda/Acura:
Accord7/TSX 03'-07' ECU 7055 [512]Matsushita K 37805-RBA-Xxxx; 37805-RBB-Xxxx
Accord7 05'-07' ECU 7058[1024]K Keihin 37805-RAD-Xxxx
2006 TSX ECU 7058[1024]Matsushita K 37805-RBA-Xxxx
Legend/CR-V 02'-07' ECU 7058[1024]K Keihin 3780..
$92.91
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$743.28 $542.86
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.85
FID: 340
Module for working with Honda/Acura cars via CAN bus with Keihin control units.
The family supports control units:
Keihin SH7058 (1MB)
Keihin SH72543 (2MB)
Keihin MPC5554 (2MB)
Keihin TC1782 (2.5MB)
Keihin TC275 (4MB)
Ke..
$309.13
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.88
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.85
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.86
FIDs: 346, 347
A module for working on a CAN bus with control units of Peugeot and Citroen petrol cars.
PSA Valeo V46.11 (FID: 346)
The control unit is powered by a Renesas SH72544 processor with 2.5 Mb internal flash memory. Allows reading and writing of the..
$179.29
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.82
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.92
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.76
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.88
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
$239.88
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.88
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.94
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.36
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.30
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.99
A set of their 5 modules discount for Toyota cars.
The kit includes:
Denso Toyota Gen1 CAN
Toyota Denso Gen2/newGen CAN
Toyota Denso Gen3 CAN
Toyota Delphi Gen1 CAN
Toyota Gen1 Virtual Reader
..
$1 019.50
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.85
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
$123.65
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.88
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.92
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.92
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
$239.88
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
$359.82
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.85
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.94
FIDs: 142, 143, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 349, 353
A module for working with gasoline, electric and diesel cars with Denso SH72xxx CAN control units.
The work is performed when connected to the table via the CAN bus. Removing the ECU is necessa..
$239.88
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.91
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.71
FIDs: 155, 157, 177
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.
Renault Siemens SID301 (FID:157)
This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0..
$239.88
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.79
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.85
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.88
FID: 64, 103
Service module for identification and virtual reading of the firmware control unit Denso 32920-4xxxx. The ECU is powered by a Renesas SH7052 CPU.
Read the actual flash memory of a given block is only possible by drilling a fairly large hole in the hull f..
$119.94
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.88
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.23
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.79
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.78
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.79
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.85
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
$239.88
1.6 L CFNA/CFNB/CLRA 7GV K-Line (Marelli 7GV/832KB) [RD/WR/CK]
1.4 L CGGB K-Line (Marelli 7GVE/832KB) [RD/WR/CK]
1.6 L BFQ K-Line (Simos 3.3 A/512KB) [RD/WR/CK]
1.4 L BUD/BXW/CGGA/CGGB K-Line (Marelli 4HV/832KB) [RD/WR/CK]
1.6 L BSA/BSE/BSF Calibration K-Line (Simos 7...
$66.36
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.18
Set of 3 modules at a discount.
BMW Bosch Exx CAN
Fxx Bosch ENET
Fxx/Gxx Bosch MG1/MD1 ENET
..
$1 079.47
The module is designed to read and write FLASH memory of ECU Siemens 5WY (5 connectors, cars KIA, Hyundai) Siemens 5WY SIMK31 (2 connectors, cars Chery QQ) Siemens MS43 via BootStrapLoader.
..
$29.82
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.88
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.82
The module is designed to work with Bosch ECU installed in the Honda cars. Supported ECU MED17.9.3, EDC17C58 (write after unlocking in BSL) as well as EDC17CP06, EDC17CP16 (recording without unlocking).
PGM-FI (Bosch EDC17CP06/EDC17CP16/2MB) [WR/CK]
PGM-FI (Bosch EDC17CP50/4MB) [Unl..
$92.91
Module supported:
Read/erase error codes
Verification and recalculation of the checksum (CS)
Identification
Entry
Reading
For the following ECU's:
BRZ SH72531 [1280k] CAN 2013+
SH7058 [1024k] CAN 2007+
SH7058 [1024k] K-line 2003+
SH7..
$106.18
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.73
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.63 $73.00
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.42
The module is designed to build, edit and compare an extended error mask according to the OBD/SAE standard for SUBARU car firmware with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). The module allows you not only to turn off, but to turn back the DTC error code.
..
$39.82
The Bosch MD1CP002 (DE 832) BMW module is designed for chip tuning of BMW cars with B57D30xx and B47D20xx diesel engines.
Installed on:
3rd G20 Series
5th series G30 and G31
6th Series G32
7th series G11 and G12
8th series G14, G15 and G16
X3 S..
$331.82
The module supports the TCM/M32R CVT [512 KB/896kb/1024kb] CAN
Identification
Read/Write calibration
Read/Delete errors
Recalculation of the COP
..
$92.91
Module 3 supports reading and writing of the following types of processors of the M32r series used in both the engine control unit and the active central differential control unit:
MH8104F_(512K) by CAN
MH8104F_(512k) by Kline (repair/restoration)
MH8106F_(1024K) by CAN
..
$92.91
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.09
This module allows chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with the Abit M240 ECU.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the control program a..
$331.82
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.82
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.30
The module allows you to edit the firmware of SUBARU cars (2.0 engines) with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). Tables of UOZ, mixture composition, throttle position, torque request, error mask, etc. are available.
Supported Software:
E2UD00..
$39.82
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.88
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.88
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.91
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.91
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.91
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.91
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.88
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.94
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.88
Module for the calibration firmware different motorcycles BRP, Ducati, Arctic Cat, Stels, Dinli, etc. with the control units Continental M3C.
Available the following cards:
The calculated mass air flow to throttle position, correction of the estimated air flow correction volume..
$299.85
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A.
..
$359.82
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.88
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.88
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.91
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.88
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.79
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.88
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.88
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.88
Universal adapter to work:
panel DENSO
UART
at MBUS
The Board has the following pin:
DTR
DTS
TX
RX
IGN
GND
12V
3.3 V
5V
MBUS
Designed to work with the modules of the software complex MDFLASHER
..
$126.09
The module supports:
A quick read full dump of the processor (7058 -5 min; 7055 -2,5 min)
Slow reading, that would add ECU indiscriminately (from 50min)
The full dump of the processor (7055 -15 min; 7058 -25 min)
Recalculation of checksum
Recovery recording session..
$119.46
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.88
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.82
Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71.
Available the following cards:
The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficien..
$239.88
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.88
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.85
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.85
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
$299.85
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.91
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.88
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.94
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.94
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.88
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.88
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.82
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
$239.88
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.73
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$491.86
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.46
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
$239.88
FID: 280
Module for reading and writing by CANbus Isuzu diesel vehicles with Transtron ECUs based on Renesas SH7058, SH7059, SH72533 and SH72544.
Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)
Family for Transtron ECUs based on MCUs Renesas SH7058/SH7059/..
$179.91
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)
Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Mar..
$239.88
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.94
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
The cars ECU:
Logan / Sandero EMS3120 TC1738 [2048k] CAN
Fluence / Megane EMS3120 TC1738 [2048k] CAN
Fl..
$86.27
License 23, may be applicable at the discretion of the licensee (user) to the work:
Mazda 6, CX5, CX7 2013+ Read, Write KM/ Read, Write EEPROM.
Mazda 2.3 2014+ Read, Write KM/Read, Write EEPROM.
Mazda MX5 2015+ Read, Write KM/Read, Write EEPROM.
Mazda 3 2010-2013 Read, W..
$79.64
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.73
FID: 337
A module for reading and writing Shindengen control units installed on Honda motorcycles.
Honda Moto Shindengen V850/RH850 K-Line (FID:337)
Sihndengen engine control units are powered by Renesas V850/RH 850 series processors with 256/384Kb internal flash memo..
$247.30
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
$359.82
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
$239.88
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
BitBox is an evolving software package that allows to identify, read and write the internal ..
$46.99
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
$359.82
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.82
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.85
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
$299.85
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.85
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
$239.88
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.38
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary f..
$99.55
CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1.
Power supply.
To work CombiBox must submit the stabilized voltage..
$92.91
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
Module ACDelco Delphi intended read / write FLASH memory of ECU Delphi ACDelco E37/E38/E39/E67/E78/E83 installed on Chevrolet and Opel via the diagnostic connector.
Table of applicability ACDelco E37 (2.4 L — LE5/LE9):
Chevrolet Captiva (C140) 2011+
Opel Antara 2011+
..
$119.46
The module is designed to work in service mode (on the table) with Bosch transmission control units with SH725xx family microcontrollers used in ZF 8HP, VAG DQ380/381/500, MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. It supports reading, writing, checking and correcting CS in FLASH memory and rea..
$132.73
Toyota Camry, Rav4 cars with 2.4L 2AZ-FE petrol engines
Supported versions:
89663-02802-
89663-02822-
89663-06431-
89663-33021-
89663-33041-
89663-33691-
89663-33701-
89663-33702-
89663-33720-A
89663-33721-
..
$39.82
Supports read and write CPU MH7201F, MH7201F with ext. flash MH7202F, MH7203F, MH8206F, MH8305F
..
$79.64
Supports recording and reading of the gasoline auto. Ford with volumes from 1.8 to 2.0, from about 2004 to 2011. MONDEO IV, S-MAX, GALAXY etc
..
$53.09
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$331.82
Supports reading and writing of the gasoline auto. Ford with volumes of 1.4 to 1.6, from about 2004 to 2009. FOCUS 2, C-MAX, KUGA, FIESTA, FUSION etc.
..
$39.82
The module is designed to read and write FLASH memory of ECU Siemens 5WY SIMK41, SIMK43 (2 slots), Siemens EMS 3132, Sirius D3/D4/D32/D42, Siemens SIM2K47 via BootStrapLoader.
..
$29.82
The Bosch EDC17CP09 module (P_573 DDE73), (P_574 DDE73a), (P_613 DDE73) is designed for chip tuning of BMW cars with N57xx diesel engines. Installed on:
3rd series E90, E91, E92 and E93
5th Series F07
7th series F01 and F02
X5 E70 Series
X6 Series E71
Pay att..
$199.09
The Bosch EDC17CP45/CP 49 module (DE 731 P_730), (DDE731a P_731), (DDE731a P_731), (DDE751a P_1319) is designed for chip tuning of BMW cars with N47xx, N57xx, and B47xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, and F23
3rd series F3..
$331.82
The Bosch EDC17C50 (DE 701) BMW module is designed for chip tuning of BMW and MINI cars with N47x, B47xx and B37xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, F23, F45 and F46
3rd series E90, E91, F30, F31, and F34
4th series F32, ..
$331.82
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 193.23
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.40
Honda: Accord 2003-2005 7 (Matsushita RBA/RBB SH7055/512KB) [VR/WR/CK]
Honda: Accord 7 2006-2007/TSX 2004-2005 (Matsushita RBA/RBB SH7055/512KB) [VR/WR/CK]
Acura: TSX 2006 (Matsushita RBB A56-A62 SH7058/1MB) [VR/WR/CK]
Honda: Accord/CR-V/Element/Legend/Odyssey/Ridgeline (Kei..
$92.91
![[51] Bosch MEDC17 - Bench](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[51] Bosch MEDC17 - Bench")
