Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
The module is designed to work with the Denso ECU with the R7F702002 microcontroller installed in Toyota and Lexus vehicles with 3.5T (V35A-FTS) and 2.4T (T24A-FTS) gasoline engines from the 2022 model year (Toyota Tundra/Tundra Hybrid/LC300/Highlander, Lexus NX350/RX350/LS500/LX600). Reading and..
$199.34
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
The cars ECU:
Logan / Sandero EMS3120 TC1738 [2048k] CAN
Fluence / Megane EMS3120 TC1738 [2048k] CAN
Fl..
$86.38
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
The module is designed to work with ECU Mitsubishi and Denso installed with gasoline engines in vehicles Mazda with the 2019 model year. Supported read, write, review, and correction of the COP.
1.5L, 2.0L, 2.5L SKYACTIV-G P5/PA/PE/PY MY2019 (Mitsubishi) [PYFA] [RD/WR/CK]
1.5L, 2.0L..
$93.03
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
Module for motor vehicles GAS, SHAANXI, FAW with the control units EDC17CV44/54 using Mscan EDS-24.
..
$66.45
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
$359.60
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
License 08, may be applicable at the discretion of the licensee (user) to the work:
The work is done by upgrading the Flash file.
Works as an editor.
DENSO engine control units on NEC 76F00xx processors with firmware size are supported 256, 320, 368, 384, 496, 736, 992, 1024.
..
$79.74
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.80
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.89
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
The module is designed to work on the UDS Protocol with the ECU CPGDSH2.24.1 and CPEGD2.20.1 etc, installed on a/m Kia/Hyundai c gasoline engine supports reading calibrations, recording, verification and correction of the COP.
1.6L (CPGDSH2.24.1/CPEGD2.20.1/UDS) [RD/WR/CK]
1.4T, 1.6..
$132.89
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
The module is designed for chip tuning of VAG cars with gasoline engines 1.8TFSI and 2.0TFSI of the third generation: Audi A4/ A5 / A6, Audi Q3 / Q5, Audi TT, Porsche Macan, Skoda Octavia, Skoda Octavia RS, VW Passat, VW Polo GTI, VW Jetta, VW Tiguan, etc.
Note:
Third-party mod..
$239.21
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
The module is designed for chip tuning of Korean-made cars of 2018 and newer with GDI gasoline engines equipped with Kefico CPEGD2.20.1 / CPEGD2.20.2 / CPEGD2.20.3 / CPGDSH2.26.1 / CPGDSH2.26.3 / CPGPSH2.14 ECUs.1.
These ECUs are used on cars such as:
Hyundai Elantra, Avant..
$265.79
The module is designed for chip tuning of VAG group cars with gasoline engines, Bosch MG1CS001 ECU, for example:
Audi A1 2.0 TFSI
Audi A3 2.0 TFSI
Audi A4 2.0 TFSI
Audi A5 2.0 TFSI
Audi A7 2.0 TFSI
Audi Q2 2.0 TFSI
Audi Q3 2.0 TFSI
Audi Q5 2.0 TFS..
$186.05
Daewoo, ZAZ Ukrainian Assembly, GAS.
..
$39.87
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
The car 'Lada Vesta/XRay/Largus' with electronic gas pedal, equipped with ECU M86/M74M.
The module is intended for read-write FLASH/EEPROM ECU М86 with a production of vases, based on the Infineon processor family XC27x5 via the built-in BootStrapLoader, and recording via the d..
$66.45
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$66.45
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$33.22
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$33.22
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
The module allows you to produce professional chip tuning of cars VAZ with electronic gas pedal (EGAS), equipped with the latest ECU M74. Also supports editing firmware ECM M74K (VAZ 'Classic', without an electronic gas pedal). Edited over 380 calibrations of the control system M74: starting mode..
$106.32
Includes maps calibrations for all firmware M74, М74CAN and М74к.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the..
$53.16
Ford Mondeo 4: 1.6 L Sigma Ti-VCT 110/125PS (EMS2101) [RD/WR/CK]
Ford Mondeo 4: 2.0 L Duratec HE (ESU312 Galaxy/S-Max 2006) [RD/WR/CK]
Ford Mondeo 4: 2.0 L, 2.3 L Duratec HE (ESU412/415) [RD/WR/CK]
Ford Mondeo 4: 2.5 L I5 Duratec 225PS (ME9.0) [WR/CK]
..
$93.03
Ford Fiesta: 1.25L, 1.4L Sigma Ti-VCT (EMS2102) [RD/WR/CK]
Ford Fiesta: 1.6L Sigma Ti-VCT (EMS2101) [RD/WR/CK]
Ford Fiesta: 1.6L Sigma Ti-VCT USA [AE81] (EMS2205) [RD/WR/CK]
Ford Mondeo 4: 1.6L Sigma Ti-VCT 110/125PS (EMS2101) [RD/WR/CK]
..
$66.45
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.73
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.73
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
MH Generic Read-Only [RD]
Colt MT (MH8304F/512KB) [RD/WR/CK]
Colt AT (MH8304F/768KB) [RD/WR/CK]
Colt RallyArt 1.5T (MH8104F/512KB) [RD/WR/CK]
Galant 9 2.4L (2005-) (MH8304F/768KB) [RD/WR/CK]
Pajero MT (2007-) (MH8302F/512KB) [RD/WR/CK]
Pajero AT (2007-) (MH..
$119.61
Ford Focus 3: 1.0 L GTDI Ecoboost 100/125PS (MED17) [RD/WR/CK]
Ford Kuga 2: 1.6 L GTDI Ecoboost 150PS FWD (MED17) [RD/WR/CK]
Ford Fiesta: 1.0 L Ecoboost GTDI 100/125PS (MED17) [RD/WR/CK]
..
$66.45
Ford Focus 3: 1.6 L Ecoboost GTDI 150/180PS (MED17) [RD/WR/CK]
Ford Mondeo 4: 2.0 L Ecoboost GTDI 200/240PS (MED17) [RD/WR/CK]
..
$66.45
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
The module is intended for read / write FLASH and EEPROM ECU MIKAS-12, M74.5, M75 and M86 running programs production ELKAR/ITELMA installed on new cars UAZ and VAZ with electronic gas pedal.
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new for..
$106.32
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
$299.66
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
This module allows you to make chip-tuning BMW MS42 ECU (engine MT52TU, Serie 3 E36, 5 E39 Serie) and MS43 (E46 Serie 3, Serie 5 E39, X5 E53). The module works in conjunction with ChipTuningPRO 7 or higher. The ECU programming is done using the loader CombiLoader.
Maps contain more than 150 c..
$93.03
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.8 ECU. More than 900 calibrations of the M74.8 control system are available for editing, allowing virtually unl..
$159.47
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$239.21
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
New cars VAZ with electronic gas pedal.
..
$106.32
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of ca..
$66.45
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Recalculation of the checksum
Supported models:
FIESTA 7(VII) 1400 TDCI Power 68
FIESTA 7(VII) 1400 TDCI Power 68
GALAXY 2000 TDCI Power 13..
$39.87
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.45
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.87
For chip-tuning of cars of Chinese production with electronic gas pedal.
..
$119.61
For owners module M75
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To ..
$46.51
The module is designed for Chip tuning TCM (TCU) module automatic transmission has the internal name of the Power Stroke and mounted on the following models Ford F450, F350, F250, Explorer, Edge, Territory, and other
List of cars:
Car Ford MY11 E265 ASSY PART AR79-14C337-AC 201..
$93.03
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.73
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.73
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
$239.73
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
Work with ECU Hitachi processor SH72533 installed on modern vehicles X-Trail, Qashqai, Juke, Teana, Murano, Patrol, Pathfinder and others with the 2014-2016 model years. The type definition module, read and write calibration check/correction checksums.
EFI SH72533 Gen 2 (2014+) Calibratio..
$66.45
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
$132.89
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
$359.60
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
Designed for chip-tuning GAS with the installed ECU M12.3. Supported read and write FLASH via diagnostic connector
..
$66.45
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/butto..
$79.74
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.74
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.61
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A.
..
$359.60
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$239.21
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
Toyota Camry, Highlander, and Lexus cars with 2GR-FE 3.5l gasoline engines
Supported BY:
89663-06772- 89663-06G70- 89663-06P00- 89663-0E050-A 89663-0E340- 89663-22290-A 89663-30A11- 89663-33340-A 89663-33341- 89663-33640-A 89663-33641- 89663-33642- 89663-33650-A 8966..
$39.87
Available only when the module M73
Includes maps of the calibration firmware the GAS Mikas 11/11CR/11ET. Works with standard format firmware.
..
$26.58
Supports reading and writing of the gasoline auto. Ford with volumes from 1.3 to 1.6, from about 2004 to 2009. FOCUS 2, C-MAX, KUGA, FIESTA, FUSION etc.
..
$39.87
FIDs: 142, 143, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 349, 353
A module for working with gasoline, electric and diesel cars with Denso SH72xxx CAN control units.
The work is performed when connected to the table via the CAN bus. Removing the ECU is necessa..
$239.73
Supports reading and writing of the gasoline auto. Mazda volume 1.3 1.5 1.6 with automatic and manual transmission 2009+ also supports reading and writing external EEPROM containing the VIN.
..
$79.74
Toyota Avensis cars with 2ZR-FAE gasoline engines, volume 1.8. Cost: 3000r.
Supported Software:
89663-01032-
89663-01121-
89663-02023-
89663-02161-
89663-02162-
89663-02172-
89663-02173-
89663-02182-
89663-02183-
89663-0..
$39.87
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.81
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055S/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7058/1MB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2007+ CAN-bus (SH7058S/1MB) [RD/..
$119.61
Supports recording and reading of the gasoline auto. Ford with volumes from 1.8 to 2.0, from about 2004 to 2011. MONDEO IV, S-MAX, GALAXY etc
..
$53.16
Supports reading and writing of the gasoline auto. Ford with volumes from 1.8 to 2.0, from about 2004 to 2011. FOCUS 2, C-MAX, KUGA etc
..
$53.16
Supports reading and writing c Mazda gasoline engines the Sky Active 2.0 2.5, on which are installed an ECU manufactured by Mitsubishi.
..
$66.45
Supports reading and writing of the gasoline auto. Ford with volumes of 1.4 to 1.6, from about 2004 to 2009. FOCUS 2, C-MAX, KUGA, FIESTA, FUSION etc.
..
$39.87
This module allows you to make chip-tuning of cars GAZ and UAZ vehicles that equipped with ECU Mikas-11, Mikas-11CR, Mikas-11ET, VS-8.
Supports the following versions:
The number of the ECU and firmware version of the ECU
824.3763.001-05 0789_101
821.3763.000-01 0..
$66.45
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.61
The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles.
..
$106.32
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.73
Supports reading and writing of the gasoline auto. Ford with volumes from 1.2 to 1.6. MONDEO, FIESTA, etc.
..
$66.45
The module is designed for Chip tuning Mazda 2019 model year, are equipped with ECU Denso by Frima {PYFB} Mitsubishi {PYFA} and engines 1.5 L, 2.0 L, 2.5 L, 2.5 T
List of cars:
Car Mazda CX-3 DK 2019 Denso OBD 78
Car Mazda CX-5 KF 2019 Mitsubishi OBD 78
..
$93.03
Supports reading and writing of the gasoline auto. Mazda with volumes 2.0, 2.5, 2.3 T - CX7,3,6 2010+
..
$93.03
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
$239.73
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
Module features:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Recalculation of the checksum
Supports reading Full Flash and recording calibrations, Subaru gasoline cars, ECU manufactured by Hitachi/Unisia Jecs with ..
$119.61
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
$299.66
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
For owners module M74 6.38
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works ..
$46.51
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.9 ECU. More than 900 calibrations of the M74.9 control system are available for editing, allowing virtually unl..
$159.47
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.32
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
$239.73
The module is intended for editing of data logger units UAZ M86I and Микас12 (GAS) with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training da..
$26.58
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.74
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
The module is designed for Chip tuning ECU SID211 installed on the following models Ford Transit, Ranger, Tourneo Connect diesel 2.0 L Ecoblue engine.
List of cars:
Car Ford PANTHER 2.0 105/130PS S/S GK21-14C204-AAA Continental TC1791 OBD 88
Car Ford PANTHER 2.0 105/130PS ..
$93.03
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.58
Toyota Camry, Rav4, Avensis cars with gasoline engines 1AZ-FE, 3ZR FAE, 3ZR-BE, 3ZR-FE, volume 2.0
Supported software:
89663-05A11-
89663-06460-
89663- 06B40-
89663-06E10-
89663-42053-
89663-42192-
89663-42590-
89663-42600- Ah
..
$39.87
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
$239.73
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.45
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.53
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.73
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
The module is designed for operation with control units petrol engines and turbo diesel installed in vehicles Land Rover Freelander 2, Evoque, Discovery Sport etc. Supported read, write, calibration, validation and correction of the COP.
Discovery 3 2.7L TDV6 (SID201/SID204) [RD/WR/CK]
..
$159.47
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.89
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb.
Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture,..
$239.73
Module 'Denso SH7058 ECU - OBDII' is designed to read and write FLASH memory of ECU Denso SH7058 processor fitted to cars Suzuki, Mitsubishi, Volvo, and others circa 2007 - 2010 model years. Please note that only supports Denso ECUS in which the manufacturer laid the engineering way of working wi..
$113.19
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
The module is designed to work with the ECU EMS3155, SID309, Hitachi CPU RH850 working on the UDS Protocol and installed in vehicles with petrol engines 1.2 l and diesel 1.5 l Supported read, write, review, and correction checksums.
1.2 T EMS3155 UDS (TC1782/2.5 MB) [RD/WR/CK]
1.5 L..
$132.89
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 8..
$66.45
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.66
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
The module is designed for chip tuning of VAG cars with 1.8 TFSI and 2.0 TFSI petrol engines of the 3rd generation: Audi A4 1.8 TFSI, Audi A5 1.8 TFSI, Audi A5 2.0 TFSI, Audi A6 1.8 TFSI, Audi Q5 2.0 TFSI, Skoda Octavia 1.8 TFSI, Skoda SuperB
Pay attention:
A third-party de..
$239.21
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$132.89
The module is designed to work with ECU Bosch ME7.9.20 installed on the Nissan X-Trail T31 petrol engine volume of 2.5 L. is Supported by the record validation and correction checksums.
EFI ME7.9.20 Calibration (ST10F275 Bosch EXT/512KB) [WR/CK]
..
$66.45
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
License 138, may be applicable at the discretion of the licensee (user) to work with:
ECU EGS gasoline engines installed on UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(full content)
FLASH recording (control program + calibration area or ..
$66.45
The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices.
The modules support the following types of ECUS:
MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB.
MagnetiMarelli MM7GV:..
$66.45
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.89
What is this system?
If You have several branches or regular customers that You make the firmware and they are interested in our product – they can get all the modules that You have, but they will not have access to the firmware, and You will keep the secret of your development. Th..
$299.66
Designed for read-write FLASH memory of ECU Cummins CM2150/2220/2880/2350 mounted on GAZ/MAZ/KAMAZ etc. via the diagnostic connector.
..
$199.34
GAZ. AT ITELMA
..
$106.32
For programming ECU VS-5.6, you must use a special adapter, the cost of the adapter is included in the cost of the module. Required shipping of the adapter to the user.
The vehicles are equipped with ECU ITELMA VS-5.6.
..
$33.22
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
Cars equipped with ECU М124 (new version ECU Mikas, for installation on automobiles GAZ.).
..
$53.16
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb.
Currently it supports the following calibration: the ignition timing for h..
$239.73
Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor.
Available the following cards:
Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure ..
$239.73
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
$239.73
For chip-tuning of cars Tagaz Tager/Road Partner and Ssang Yong Musso, Actyon, Rexton, Kyron petrol engines 2.3/2.8/3.2 L.
..
$93.03
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
A set of 7 modules to edit all available petrol cars Nissan and infiniti with the control units from Hitachi. 15% savings when ordering the kit.
The list of modules includes:
Nissan Hitachi Petrol Gen1 SH7054
Nissan Petrol Gen1 Hitachi SH7055
Nissan Hitachi Petrol Gen1 SH7..
$1 630.17
Supports reading and writing c petrol Mazda Sky Active engines of 2.0 and 2.5, which require the ECU manufactured by Denso.
Car Mazda 6 GJ 2.5L Skyactiv-G PY3GEE000PY0B060 192 DENSO SH72543 PY3G-188K2-E OBD 33
Car Mazda 6 GJ 2.5L Skyactiv-G PY3HEG000PY0B060 192 DENSO SH72543 PY3H-18..
$66.45
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.89
Toyota Camry, Rav4 cars with 2.4L 2AZ-FE petrol engines
Supported versions:
89663-02802-
89663-02822-
89663-06431-
89663-33021-
89663-33041-
89663-33691-
89663-33701-
89663-33702-
89663-33720-A
89663-33721-
..
$39.87
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.33
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.73
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
Designed for chip-tuning of cars VAZ, GAZ, UAZ, ZAZ installed the ECU Я7.2+, M11/М11ЕТ/М11CR/M73/M10.3/M11.4/ Bosch M7.9.7 and M7.9.7+
..
$66.45
FIDs: 346, 347
A module for working on a CAN bus with control units of Peugeot and Citroen petrol cars.
PSA Valeo V46.11 (FID: 346)
The control unit is powered by a Renesas SH72544 processor with 2.5 Mb internal flash memory. Allows reading and writing of the..
$179.18
The module allows you to view and edit statistics (mileage, fuel consumed), speed limit and transmission protection parameters in the configuration files *.cfg ECU Continental CM2150, CM2200, CM2220, CM2350, CM2880.
Read using the Combiloader programmer by the Cummins CM2xxx module. It is pos..
$239.21
Toyota Corolla cars with 1ZR-FE, 3ZZ-FE 1.6 petrol engines
Supported software:
89663-02240-A
89663-02241-
89663-02270-A
89663-02482-
89663-02483-
89663-02491-
89663-02492-
89663-02502-
89663-02503-
..
$39.87
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.81
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, th..
$239.73
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.05
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
$299.66
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.53
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.53
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
$119.87
Supports reading Full Flash and recording of calibrations petrol cars Suzuki, ECU manufactured by Hitachi c CPU SH7058. Recalculation of the CRC. Read & clear error ECU internal combustion engine.
Suzuki Escudo 2.7 L Suzuki Grand Vitara 2.7 L
..
$66.45
Set of 8 modules 1,2,3,4,5,6 Petrol Toyota Denso, Toyota Denso Toyota Denso OLD and Petrol Turbo. Allows you to edit all available petrol cars are Toyota, Lexus, Scion on the units of DENSO. 10% savings when ordering.
10% savings when ordering.
..
$2 049.70
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.73
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
$123.57
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering.
..
$3 236.37
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.61
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.88
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.80
Only supports record turbocharged petrol auto. Ford.
..
$39.87
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.36
Module Mikas-11.4/12.3 with support for the following ECU Mikas-11.4/12.3 (ZAZ, GAZ)
..
$82.02
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.96
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.87
