License 109, may be applicable at the discretion of the licensee (user) to the work:
via the OBDII connector or on a table with 6RF(U)92086x instrument panels(white indication) based on the 70F3524 microcontroller without an external EEPROM installed on VAG Polo cars since 2014, wh..
$199.09
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.64
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.18
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.64
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.18
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$504.37
The module is designed to delete data collision (CRASH DATA):
Toyota DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Toyota FUJITSU SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS MCU RENE..
$79.64
License 48, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
MB(CY)96F313
MB(CY)96F315
MB(CY)96F326
MB(CY)96F336
MB(CY)96F338
MB(CY)96F343
MB(CY)96F345
..
$106.18
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$119.46
Reading full image data
The writing of a complete image data
Identification
Recalculation of checksum
Work is required to remove the ECU.
Car Suzuki Carry DA16T 0.660L R06A 4WD 2014 Mitsubishi MH8115 33910-82M0 Bench 65
Car Suzuki Spacia ..
$132.73
Includes the following modules:
module SRS AIRBAG Renault Continental Temic Motorola OBD2
Allows clearing CRASH DATA in blocks on the processors 9s12XDT384+95640 .
These units were installed in the cars of Renault Fluence /Megane III / Latitude / ScenicIII / KangooII / TwingoII
..
$79.64
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.64
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.64
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.64
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.82
MH Generic Read-Only [RD]
Colt MT (MH8304F/512KB) [RD/WR/CK]
Colt AT (MH8304F/768KB) [RD/WR/CK]
Colt RallyArt 1.5T (MH8104F/512KB) [RD/WR/CK]
Galant 9 2.4L (2005-) (MH8304F/768KB) [RD/WR/CK]
Pajero MT (2007-) (MH8302F/512KB) [RD/WR/CK]
Pajero AT (2007-) (MH..
$119.46
The module allows you to view and edit data recorder, which are stored in EEPROM (for the M74 only supports internal EEPROM 64KB).
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are ..
$39.82
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work with binary images EEPROM size of 4 KB or 64 KB (the file .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalcula..
$39.82
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalculated checksum of the se..
$39.82
License 36, may be applicable at the discretion of the licensee (user) to the work:
Audi A3 Mk3 07.2014+ Reading/KM record
Audi Q2 Reading/KM record
Skoda Fabia III 07.2014+ Reading/KM record
Skoda Octavia III 07.2014+ Reading/KM record
Scoda Rapid 09.2015+ Reading..
$331.82
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalculated checksum of the se..
$39.82
The module allows you to view and edit data recorder, which are stored in the EEPROM.
It is possible to work as with binary EEPROM images (files .eep), and with container SMS-Soft Container File (files .bcf).
When you save the EEPROM image are automatically recalculated checksum of the se..
$39.82
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$92.91
The set of modules (General license):
Delphi DCM3.7 SsangYong
Delphi DCM3.7 GM
Delphi DCM3.7 GreatWall
Delphi DCM3.7 Hyundai/Kia
Delphi DCM3.7 VAG
The modules are designed to read / write FLASH memory of ECU Delphi DCM3.7, mounted on SsangYong, Opel, Chevrole..
$132.73
The module allows you to view and edit the registrar's data, which is stored in the EEPROM.
When saving an EEPROM image, the checksums of the required EEPROM areas are automatically recalculated.
..
$39.82
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.18
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$92.91
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.73
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.73
License 108, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS Siemens W3, Siemens VW51, Siemens VW52 units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data:
..
$66.36
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$92.91
License 80, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on Ford/Mazda cars,
which allows for full-fledged repair and restoration work with ECU d..
$79.64
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.40
License 42, may be applicable at the discretion of the licensee (user) to the work:
Dacia Logan RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Lada Largus FL RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, E..
$79.64
Module Functions:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports only recording and converting stock firmware from the IDS database (VCM) to bina..
$66.36
Module 'Module Bosch M78/ME797+ - OBD2' is designed to record via OBD2 connector firmware ECU Bosch M78, ME797+ cars Ukrainian and Chinese production. Currently supported ECU M78 cars ZAZ Forza, Geely CK2, Geely MK2, Geely Emgrand Great Wall Wingle, ECU M788 car JAC, Geely GC6, Chery Tiggo, Lifan..
$46.93
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.64
License 79, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Takata SRS units based on SPC560P34L1 processors installed on Lada Vesta and UAZ Patriot cars, which allows for full-fledged repair and restoration wor..
$66.36
Module features:
Reading calibrations
Recording calibrations
Reading the full data image
Recording a complete data image
Identification
Reading/erasing errors
Recalculation of the checksum
The module also supports:
..
$66.36
Supports full data image reading, full data image writing, identification, error reading/erasing, EEPROM reading/writing, checksum recalculation.
Allows you to clone Gen1 and Gen2 ACU.
..
$132.73
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.64
The module allows you to produce a professional chip tuning for Renault Logan, Renault Sandero, Nissan Almera engine 1.6 L, automatic transmission, equipped with ECU Continental/Siemens EMS3134.
Supported versions:
REA820
REA830
Features of the module:
The possibil..
$79.64
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.18
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.36
The module is designed to edit the data of the registrar of the VAZ 74.8 and M74.9 blocks with NPO Itelma. The module monitors the integrity of the data when opening and recalculates all the necessary CS when saving. An EEPROM (4 kilobytes) is used for editing.
..
$26.55
License 101 can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with multimedia units installed on GM cars, which allows for full-fledged repair and restoration work with ECU data.
Scope of application: Change of region, Us..
$331.82
License 132, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with the Continental VDO MQBAB dashboard based on the NEC35xx MK installed on cars: Audi,Skoda,Seat,VW, which allows for full-fledged repair and restoration work with ECU data.
..
$331.82
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.64
The module is intended for cloning on the table, without parsing the ECU. Supported and filled in TCU in a metal case and not filled in a plastic housing.
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
..
$132.73
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$66.36
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$119.46
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$66.36
The module is intended for editing of data logger units VAZ Bosch ME17.9.7 and ME17.9.71. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes, respectively the type of ECU).
..
$26.55
The module is intended for editing of data logger units UAZ M86I and Микас12 (GAS) with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training da..
$26.55
The module is intended for editing of data logger units M74.5 (6.38), M75 and vases M86I with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the train..
$26.55
The module is intended for editing of data logger units M74 (storing training data in flash CPU) and М86, ON 'VAZ'. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely fr..
$26.55
The module is intended for editing of data logger units UAZ Bosch M(E)17.9.7 and M(E)17.9.71. So the module allows to change the counter programmed the ECU. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes,..
$26.55
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 193.23
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.64
Designed for chip tuning of ECU Abit M20.20, M20.21, M240, M240S1, MD22. Modules allow you to: - Read and write calibration area - Read and write control program - Calculate and, if necessary, automatically correct the checksum of the calibration area - Perform ECU identification - Read and reset..
$132.73
Designed to read and record the calibration and program the ECU SID208 vehicle Peugeot Boxer/Citroen Jumper via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identifica..
$132.73
Distribution of licenses after 06/14/2024
License 144, may be applicable at the discretion of the licensee (user) to work with:
ABS ECU on MK NXP Cortex M4 (FS32K144HFMLL) installed on Lada Racing, Lada Granta FL cars from 2024.
Identification
Reading/..
$159.27
Module functions:
Recording calibrations
Identification
Reading/erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
DDE721b
DDE73a
DDE731a
MEVD17.2
..
$132.73
Module features:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Recalculation of the checksum
Supports reading Full Flash and recording calibrations, Subaru gasoline cars, ECU manufactured by Hitachi/Unisia Jecs with ..
$119.46
Reading calibrations
A record of calibrations
The writing of a complete image data
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
MED17 only a virtual reading. When tuning record-only calibrations. Stoke can record and ..
$132.73
License 58, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by CONTINENTAL.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 95..
$106.18
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.18
Reading the full data image
Recording a complete data image
Identification
Recalculation of the checksum
..
$199.09
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.18
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.27
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.36
Module supported:
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
Reading/erasing fault
Read/write EEPROM
Recalculation of checksum
..
$66.36
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.64
License 143, may be applicable at the discretion of the licensee (user) to the work:
with instrument panels on the MK Artery Cortex M4 (AT32F403) installed on Lada Granta and Lada Niva cars from 2024.
Identification
Reading/Clearing the DTC
Reading/KM Record
..
$79.64
A record of calibrations
Reading full image data
Identification
Recalculation of checksum
..
$92.91
License 18, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM recording via OBDII.
Reading/FLASH recording via OBDII.
The module only works with panels on MK 9S12XHZ256.
List of supported cars:
Nissan Qashqai 2010+
..
$66.36
Recording a complete data image
Identification
..
$132.73
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.73
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$238.91
The module allows you to produce professional chip tuning Mitsubishi Outlander XL with engines of 2.4 L and 3.0 L (manual and CVT) and Mitsubishi ASX with dvigatelem 2.0 L and Citroen C-Crosser and Peugeot 4007 made on the platform of the Outlander. Has no analogues on the number of calibrations ..
$79.64
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.99
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.64
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$663.64
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Read/write configuration data
Recalculation of the checksum
..
$79.64
Designed to read/write calibration and program the ECU Delphi DCM6.2/6.2A/6.2C installed on the Peugeot/Citroen via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identi..
$92.91
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.73
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.73
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.64
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.38
License 82, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars Nissan / Infiniti, which allows for full-fledged repair and restoration work with ECU data.
..
$79.64
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.36
The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector.
ECU Continental EMS3155 ustanavlivaetsya on engines 1.2 T.
ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L.
ECU Bosch EDC17C84 i..
$132.73
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
The price shown is for the owners of the Sirius module 3x
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allo..
$26.55
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allows you to change the VIN code in the downloaded firmware.
..
$66.36
The module allows you to produce a professional chip tuning Lada Largus cars equipped with ECU Continental EMS3120.
Supported firmware versions:
HW7908R_SW09350_90047
Features of the module:
The possibility of open firmware (FullFlash only) in BIN format or SMS-Soft Cont..
$106.18
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.63 $73.00
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.64
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.18
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$743.28 $542.86
New ECU M86 applies to cars UAZ Pro. Manufacturer software hardware — NPP ITELMA.
This module allows you to produce professional chip tuning UAZ Pro equipped ECU M86 with ITELMA. Edited more than 950 calibration management system M86, which allows full professional chip tuning UAZ...
$106.18
The module allows you to produce professional chip tuning Lada X-Ray and Renault Duster/Kaptur, equipped with ECU Continental EMS3125.
Supports any version of calibration based on series RDE450, RDE540, RDE570.
Features of the module:
About 550 of calibration..
$106.18
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.18
License 59, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
D70F3230 -D70F3231 -D70F3232 -D70F3233 -D70F3234 -D70F3235 -D70F3236 -D70F3237 -D70F3238 -D70F3239 -D70F3333 -D70F3334-D70F333..
$66.36
The module allows you to produce a professional chip tuning for Renault Logan and Renault Sandero 2 2 that equipped with ECU Continental EMS3120.
Supported IDs firmware module Logan/Sandero:
HW4319R_SW4234R_4541R
HW4319R_SW4234R_4928R
HW4319R_SW4234R_4929R
HW4319R_SW..
$106.18
The module is intended for editing data from Ieprom blocks Bosch ABS9, VAZ cars (XRAY / VESTA). You can change the main mileage, mileage after ECU reset, TPMS log mileage, VIN, Hardware ID, wheel diameter, TPMS activation flag. The module monitors the integrity of the data upon opening and recalc..
$26.55
The module is designed for operation with control units SIMK-41/43, SIM2K-47 used in vehicles Kia/Hyundai. Supported reading (when available), entry, checking and correction of the checksum, automatically detect the type of ECU.
2.0 L, 2.7 L K-Line (SIMK-41/43) [RD/WR/CK]
2.0 L, 2.4..
$66.36
Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
$143.93
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.36
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.12
Update ChipExplorer 2 from Standard to Professional
..
$58.65
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.73
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.64
License 136, may be applicable at the discretion of the licensee (user) to the work:
with direct connection via CAN bus with Magneti Marelli IAW 9 GVCE control units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data.
Magneti Marelli IAW 9GV..
$79.64
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.73
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.85
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.64
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.64
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.09
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.64
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.64
It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the..
$92.91
License 43, may be applicable at the discretion of the licensee (user) to the work:
Renault Kadjar Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Megane I V Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Espace..
$79.64
The program in Russian and English languages.
Universal programmer a large number of microcontrollers from Microchip, Atmel, Cypress, ST, etc., and also chip FLASH/EEPROM (currently more than 13000 chips). Connect to PC and power to the programmer through the USB port of the computer (5v).
..
$122.08
Module OPEL ECU - OBD2 includes work with the ECU Simtec-71.5, Simtec-71.6, Simtec-75.1, 75.5 Simtec, Simtec 81.1, Delphi MT35E, Bosch ME9.1 / ACDelco E77 (read and write FLASH memory). Supports data only ECU on the CAN bus.
..
$56.66
License 135, may be applicable at the discretion of the licensee (user) to the work:
from CCBS to MK Artery AT32F435ZGT7(FlashSize: 1024KB) installed on Lada Vesta NG cars from 2022 or Lada Largus from 2024, which allows for full-fledged repair and restoration work with these types of ECUs.
..
$331.82
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.91
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.91
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.94
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.88
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.94
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.82
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.8 ECU. More than 900 calibrations of the M74.8 control system are available for editing, allowing virtually unl..
$159.27
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.9 ECU. More than 900 calibrations of the M74.9 control system are available for editing, allowing virtually unl..
$159.27
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.09
