License 17, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording EEPROM 24c04 or 93c56 (depends on the type of panel) by OBDII or direct connection on the table (connection in the help).
Correction of odometer readings by OBDII or direct connecti..
$66.45
The module allows you to write firmware diagnostic method, without removing the ECU from the vehicle through the DLC (to work with the ECU on the car must be connected directly to the connector of the UNIT to disassemble the unit is not required).
Support ECU Bosch MSE3.0, M7.9.7, ME7.9.7, M7..
$66.45
Cable to overwrite the ECU with Combiloader and relevant modules through the DLC.
..
$26.58
This module allows you to work on a car via an OBDII connector with Siemens ECM installed on Ford cars.
OBD II Mode (working on a car or on a desk):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalcula..
$66.45
License 77, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (..
$106.32
For chip-tuning Ford Focus II with engine 1.6 L with adjustable phase timing, ECU Siemens SIM29.
..
$106.32
For chip-tuning Ford Focus II with engines 1.4—1.6 L without adjustable phase timing, ECU Siemens SIM28.
..
$106.32
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
License 41, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the ACDelco E83 ECU in OBD II Mode, Bench Mode and Recovery mode.
1. OBDII Mode(Car operation):
Reading Identification
Reading Er..
$106.32
License 74, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
License 115, may be applicable at the discretion of the licensee (user) to the work:
providing advanced functionality - working with instrument panels via the OBD II connector (where there is a technical possibility), installed on Hyundai/Kia cars since 2018, which allows for full-..
$79.74
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
License 61, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the Siemens Simtec 76 ECU in OBD II Mode and BenchMade mode.
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
..
$106.32
License 40, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of the calibration area (with recalculation of checksums)
..
$106.32
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.32
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
License 90, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
License 99, may be applicable at the discretion of the licensee (user) to the work:
1. OBDII Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculation of checksums)
..
$106.32
Module 'Module Bosch M78/ME797+ - OBD2' is designed to record via OBD2 connector firmware ECU Bosch M78, ME797+ cars Ukrainian and Chinese production. Currently supported ECU M78 cars ZAZ Forza, Geely CK2, Geely MK2, Geely Emgrand Great Wall Wingle, ECU M788 car JAC, Geely GC6, Chery Tiggo, Lifan..
$46.90
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
Module ACDelco - OBDII supports reading field calibration, full flash the ECU ACDelco E83, E39, E39A, E78, E37, E38. Recording is possible only in the area of calibrations. The module allows you to recalculate the checksum of the firmware before recording.
..
$90.04
Module Bosch ME17.9.11/12-OBD2 is designed to write FLASH memory of ECU Bosch ME17.9.11, Bosch ME17.9.12 via the J2534 device. Please note that this module can record only serial firmware!
..
$11.71
This module allows you to work on the car via the OBDII connector with the Visteon ECU installed on Ford cars.
Module Functions:
Identification Reading
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalculation of calibration area c..
$66.45
Module Delphi MT20U/MT38/MT20U2/MT22U-OBDII (cars Chery, BYD, Hoover, Lifan, Kia, Hyundai)
..
$70.27
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
The family of modules includes three separate module from the ECU to the M74.5, M75, MIKAS-12 or M86 (FOR ITELMA, firmware, VAZ and UAZ), which can be purchased independently. All the modules have identical functionality and are designed to create dual-mode firmware with an individual set of cali..
$53.16
Includes the following modules:
module SRS AIRBAG Renault Continental Temic Motorola OBD2
Allows clearing CRASH DATA in blocks on the processors 9s12XDT384+95640 .
These units were installed in the cars of Renault Fluence /Megane III / Latitude / ScenicIII / KangooII / TwingoII
..
$79.74
Module 'Denso SH7058 ECU - OBDII' is designed to read and write FLASH memory of ECU Denso SH7058 processor fitted to cars Suzuki, Mitsubishi, Volvo, and others circa 2007 - 2010 model years. Please note that only supports Denso ECUS in which the manufacturer laid the engineering way of working wi..
$113.19
Переходник для Mercedes. Используется для соединения с авто Mercedes у которых 38-контактный круглый диагностический разъем.
Работает с устройствами у которых на выходе OBD-II разъём.
..
$3.36
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
Module with support Sirius D3/D4/D32/D42/D52 (Chevrolet Aveo, Lacetti, Spark, Daewoo Matiz) is designed to read and write FLASH memory from ECU Sirius via OBDII diagnostic connector.
..
$35.12
Module Bosch ME17.9.7(1)-OBD2 with write support ECU Bosch ME17.9.7 via the OBD2 socket of the car VAZ, UAZ, as well as records with ECU Bosch ME17.9.71 UAZ.
Please note that for correct record ECU Bosch M(E)17.9.71 you must first disable the monitoring of a digital signature, and writing the..
$58.61
Module EMS3120 (VAZ/Logan) - OBD2 is designed to read and write FLASH memory of ECU Siemens EMS3120 fitted to cars VAZ, Logan via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Speci..
$63.61
The unit Valeo V40/V42 - OBDII is designed to read and write FLASH memory of ECU Valeo V40/V42 Renault cars.
The module must J2534 device.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Specify when ordering the serial number of your adapter and appl..
$45.25
Module EDC17/MED(G)17 (Kia/Hyundai) - OBD2 is designed to write FLASH memory of ECU Bosch EDC17C08, Bosch, EDC17CP14, Bosch MED(G)17.9.8 via the J2534 device.
Please note that this module can only record the previously prepared serial tuning or firmware!
..
$28.33
Module 'SIM2K-140/141/241/341/D160 - OBDII' with support for ECU Siemens SIM2K140/141/241/245 (Kia, Hyundai), Siemens SIM2K-D160 (Chevrolet Epica)
..
$90.04
Module OPEL ECU - OBD2 includes work with the ECU Simtec-71.5, Simtec-71.6, Simtec-75.1, 75.5 Simtec, Simtec 81.1, Delphi MT35E, Bosch ME9.1 / ACDelco E77 (read and write FLASH memory). Supports data only ECU on the CAN bus.
..
$56.62
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
The Bosch module M(E)7.9.7-OBDII (Bosch Kefico M7.9.7, Bosch M7.9.7(+) (VAZ), Bosch M7.9.7+ (Geely cars, Amulet), Bosch M7.9.7.1 (Chevrolet Aveo), Bosch ME7.9.7 (Chery cars))
..
$11.71
Module Bosch ME17.9.11/12/13/21 - OBD2' is designed to read and write via OBD2 connector tuning and serial firmware. This module provides a fake digital signature of the downloaded firmware to enable it write via OBD2 connector.
..
$91.02
Module GM MT60/MT80 Extended - OBD2 is designed to read and write full dump of the internal FLASH and EEPROM memory of ECU MT60/MT80 manufactured by GM. The module can be used to cloning units.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lit..
$84.82
Module GM SIM2K-243 - OBD2 is designed to read and write FLASH memory of ECU SIM2K-243 installed in the cars of GM via the J2534 device.
Supported the conversion and checksum field calibrations.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. ..
$68.54
The module is designed for recording and reading (read-only ECU Avtel M73) FLASH memory of the ECU family January-7.2+/M73 via diagnostic connector OBDII
At the moment not supported the ECU Avtel M73 with identifiers ending in DB04, and having such protection algorithms.
..
$11.71
Module 'China MT80 ECU - OBDII' is designed to read and write FLASH memory of ECU MT80 installed on Chinese vehicles through J2534 device and KLine adapter.
Supported the conversion and checksum. Recording is performed only in the area of calibrations.
For holders of CHIPSOFT J..
$93.09
Module 'VW Polo ECU - OBDII' is designed to read and write FLASH memory of ECU Magnetti Marelli 7GV, 7GVE, 4HV, installed on the cars of VW via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% disco..
$88.17
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$93.03
License 132, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with the Continental VDO MQBAB dashboard based on the NEC35xx MK installed on cars: Audi,Skoda,Seat,VW, which allows for full-fledged repair and restoration work with ECU data.
..
$332.24
Module Delphi HV240/MR140-OBDII (Chevrolet Aveo, Lacetti)
..
$70.27
Module Simtec 76/Delphi MT60/MT80 - OBD2 (Chevrolet)
..
$56.73
This module is designed to read / write FLASH and EEPROM memory of ECU M74 in boot mode . Working with this type of ECU is performed via K-Line adapter for the ECU M74 and through the J2534 device to the ECU M74CAN.
The ECU is mounted on the automobiles.
For significant acceleration of th..
$23.41
The module is designed to read and write FLASH memory from ECU ME7.9.9 Chevrolet Captiva via OBDII diagnostic connector.
..
$58.61
The module is designed to read and write FLASH memory of ECU MT86 installed on a KIA/Hyundai. Working with these types of ECU's is via the J2534 device
ECU MT86 is a read only field calibrations. Recording is supported for the following formats:
Firmware reads th..
$42.41
Module TC1762/TC1766/TC1796/TC1797/TC1767/TC1724/TC1738/TC1791/TC1793/TC1798/TC1728/TC1782/TC1784/GPT boot mode (ECU families Bosch ME17.9.x and other CPU Tricore TC1762 / TC1766 / TC1796 / TC1797 / TC1767 / TC1724 / TC1738 / TC1791 / TC1793 / TC1798 / TC1728 / TC1782 / TC1784)
Clo..
$180.15
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
License 13, may be applicable at the discretion of the licensee (user) to the work:
Reading/Clearing fault codes
Clearing collision information.
Unlocking the ECU.
Changing the ECU configuration.
Reading/VIN entry.
List of supported ECUs:
Renault SAND..
$79.74
License 36, may be applicable at the discretion of the licensee (user) to the work:
Audi A3 Mk3 07.2014+ Reading/KM record
Audi Q2 Reading/KM record
Skoda Fabia III 07.2014+ Reading/KM record
Skoda Octavia III 07.2014+ Reading/KM record
Scoda Rapid 09.2015+ Reading..
$332.24
With contact to connect the voltage programming enable Aux
..
$27.91
Distribution of activation files after 11/30/2022
License 98, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode (Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading..
$106.32
Instead of a main cable + adapter OBDII-16
..
$23.92
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$93.03
The module is designed to record the FLASH memory of the ECU M 7.9.8 7.9.8 and MG via OBDII diagnostic connector.
..
$70.31
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
The module is designed to read and write FLASH memory of ECU frame-mounted Mazda (2003-2013 year of release) via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 ( Lite) (Mid) adapter, a 50% discount on the module. Specify when o..
$93.09
License 34, may be applicable at the discretion of the licensee (user) to the work:
Renault Megane III Reading/KM Recording ,Reading/EEPROM recording in the ABS/CDC/ESP blocks of the ATE manufacturer
Renault Laguna III Reading/KM Recording ,Reading/EEPROM recording in the ABS/C..
$159.47
The module is designed for Chip tuning ECU SID211 installed on the following models Ford Transit, Ranger, Tourneo Connect diesel 2.0 L Ecoblue engine.
List of cars:
Car Ford PANTHER 2.0 105/130PS S/S GK21-14C204-AAA Continental TC1791 OBD 88
Car Ford PANTHER 2.0 105/130PS ..
$93.03
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to work on diagnosticheskogo the OBD2 port. To read a complete image of the Flash memory are written only calibration.
..
$93.03
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.61
Module Ford ECU Siemens SIM28/SIM29/SIM210/SIM22 / EMS2204 / SID206, Visteon ESU-131/411/412/415/418 - OBD2 is designed to read and write FLASH memory of ECU Siemens SIM28, SIM29, SIM210, SIM22, EMS2204, SID206, Visteon ESU-131/411/412/415/418 - OBDII Ford vehicles.
The mod..
$48.98
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
License 11, may be applicable at the discretion of the licensee (user) to the work:
Renault MeganIII/Scenic III/Fluence/ClioIII/Modus
Restores the eeprom Eur dump (EPS), makes it "new" - ready for installation on the car.
Identification of the ECU.
Read..
$106.32
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.45
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.96
License 109, may be applicable at the discretion of the licensee (user) to the work:
via the OBDII connector or on a table with 6RF(U)92086x instrument panels(white indication) based on the 70F3524 microcontroller without an external EEPROM installed on VAG Polo cars since 2014, wh..
$199.34
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.89
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.18
The module is designed to read, write, FLASH memory of various types of ECU Siemens via OBDII diagnostic connector.
..
$82.02
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.89
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.47
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.32
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
Module features:
Reading calibrations
Recording calibrations
Reading the full data image
Recording a complete data image
Identification
Reading/erasing errors
Recalculation of the checksum
The module also supports:
..
$66.45
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
License 39, may be applicable at the discretion of the licensee (user) to the work:
Subaru Outback 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Subaru Legacy 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Not all software versions may be supporte..
$79.74
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.32
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.45
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
License 85, may be applicable at the discretion of the licensee (user) to the work:
Correction of mileage readings with recalculation of checksums in the read EEPROM area of the processor firmware,
in DSG DQ200, DSG DQ200_MQB, DSG DQ200 G2, DSG DQ250 E/F(02E) units installed on..
$79.74
License 27, may be applicable at the discretion of the licensee (user) to the work:
Hyundai/KIA MB91F061/062/067 WITHOUT EXTERNAL EEPROM
The work is carried out through the OBDII connector
Approximate operating time from 4 - 10 minutes
The list of cars is approxim..
$79.74
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.89
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
License 80, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on Ford/Mazda cars,
which allows for full-fledged repair and restoration work with ECU d..
$79.74
License 79, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Takata SRS units based on SPC560P34L1 processors installed on Lada Vesta and UAZ Patriot cars, which allows for full-fledged repair and restoration wor..
$66.45
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.74
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.74
License 108, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS Siemens W3, Siemens VW51, Siemens VW52 units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data:
..
$66.45
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.32
License 19, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording KM by OBDII.
Reading/Recording HERPROM by OBDII.
Reading FLASH by OBDII.
Nissan/Infiniti cars from 2011 and above with the Continental VDO NEC 34+24C16 dashboard are sup..
$79.74
Distribution of activation files after 01.06.2023
License 118, may be applicable at the discretion of the licensee (user) to work:
with a Bosch electric power steering on the Nec V850 70F3187 + EEPROM 95080 MK on the table or via the OBDII connector (where there is a technical ..
$66.45
License 82, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars Nissan / Infiniti, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.74
License 68, may be applicable at the discretion of the licensee (user) to the work:
1. Auto-search Mode:
Reading the mileage of HYUNDAI / KIA cars by OBDII with the MED17/EDC17 ECU.
Automatic search for the specified mileage in the EEPROM dump loaded into the program...
$106.32
License 18, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM recording via OBDII.
Reading/FLASH recording via OBDII.
The module only works with panels on MK 9S12XHZ256.
List of supported cars:
Nissan Qashqai 2010+
..
$66.45
The module is designed to work with the Denso ECU with the R7F702002 microcontroller installed in Toyota and Lexus vehicles with 3.5T (V35A-FTS) and 2.4T (T24A-FTS) gasoline engines from the 2022 model year (Toyota Tundra/Tundra Hybrid/LC300/Highlander, Lexus NX350/RX350/LS500/LX600). Reading and..
$199.34
License 44, may be applicable at the discretion of the licensee (user) to the work:
Read/Write FLASH processors SH7058,SH7059,R4F70580, R4F70590 (without recalculation of checksums).
Read/Write Opel EEPROM
Read/Write Mitsubishi EEPROM
Read/Write Suzuki EEPROM
Readi..
$106.32
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.32
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
The module allows you to produce professional chip tuning of cars VAZ with electronic gas pedal (EGAS), equipped with the latest ECU M74. Also supports editing firmware ECM M74K (VAZ 'Classic', without an electronic gas pedal). Edited over 380 calibrations of the control system M74: starting mode..
$106.32
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.89
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.89
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.87
Work with ECU Hitachi processor SH72533 installed on modern vehicles X-Trail, Qashqai, Juke, Teana, Murano, Patrol, Pathfinder and others with the 2014-2016 model years. The type definition module, read and write calibration check/correction checksums.
EFI SH72533 Gen 2 (2014+) Calibratio..
$66.45
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$239.21
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055S/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7058/1MB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2007+ CAN-bus (SH7058S/1MB) [RD/..
$119.61
The module is designed for Chip tuning TCM (TCU) module automatic transmission has the internal name of the Power Stroke and mounted on the following models Ford F450, F350, F250, Explorer, Edge, Territory, and other
List of cars:
Car Ford MY11 E265 ASSY PART AR79-14C337-AC 201..
$93.03
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
License 53, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to read and write a full memory image (FULL FLASH) for cloning the ECU.
List of supported ECUs:
Simtec 71.5
Simtec 71.6
Simtec 75.1
Si..
$106.32
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.89
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
License 101 can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with multimedia units installed on GM cars, which allows for full-fledged repair and restoration work with ECU data.
Scope of application: Change of region, Us..
$332.24
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
$359.60
License 16, may be applicable at the discretion of the licensee (user) to the work:
ECU on the MB96F386+95160 microcontroller
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording(program area + calibration)
..
$79.74
MH Generic Read-Only [RD]
Colt MT (MH8304F/512KB) [RD/WR/CK]
Colt AT (MH8304F/768KB) [RD/WR/CK]
Colt RallyArt 1.5T (MH8104F/512KB) [RD/WR/CK]
Galant 9 2.4L (2005-) (MH8304F/768KB) [RD/WR/CK]
Pajero MT (2007-) (MH8302F/512KB) [RD/WR/CK]
Pajero AT (2007-) (MH..
$119.61
License 15, may be applicable at the discretion of the licensee (user) to the work:
ECU on the NEC 34+24C16 microcontroller:
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording (program area + calibration)
..
$79.74
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.74
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.74
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.74
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.79
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.33
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$106.32
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$53.16
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$106.32
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$53.16
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
The module is designed for Chip tuning Mazda 2019 model year, are equipped with ECU Denso by Frima {PYFB} Mitsubishi {PYFA} and engines 1.5 L, 2.0 L, 2.5 L, 2.5 T
List of cars:
Car Mazda CX-3 DK 2019 Denso OBD 78
Car Mazda CX-5 KF 2019 Mitsubishi OBD 78
..
$93.03
Supported reading (where possible), write via OBD and correction KS for vehicles with engines of 1.1, 1.4, 1.6 liters.
Kia/Hyundai: 1.4L, 1.6L (ME17.9.11/12/13) [RD/WR/CK]
Kia/Hyundai: 1.4L, 1.6L (ME(G)17.9.21/17.9.21.1) [RD/WR/CK]
Kia/Hyundai: 1.6L, 3.0L (ME17.9.2/ME(D)(G)17...
$93.03
License 75, may be applicable at the discretion of the licensee (user) to the work:
Reading/FullFlash Entry
Reading/EEPROM recording
The ability not to overwrite the boot sector.
The module allows you to use your Seed Key, in case it was replaced with a non-s..
$106.32
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.74
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.74
The modules are designed to read / write ECU Continental SIM2K-250/251/253/260/261 that are installed on vehicles Hyundai/Kia.
No need to opening the ECU. In diagnostic mode the available functions of identification, read/clear faults and recording and/or calibrations.
The mo..
$132.89
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.89
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.32
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
License 02, may be applicable at the discretion of the licensee (user) to the work:
Continental SID 305 Reading/KM record
Continental SID 306 Reading/KM record
Continental SID 307 Reading/KM record
Continental SID 309 Reading/KM record
Delphi DCM3.4 Reading/KM reco..
$106.32
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
Virtual reading (one button, the program downloads the Ford servers need VBF)
Conversion of VBF to BIN
BSL
Reading firmware
Read the password in OBD mode
Unlock in BSL for..
$66.45
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
License 29, may be applicable at the discretion of the licensee (user) to the work:
Recording the mileage of dashboards on EEPROM 95040 cars before 2011
Recording the mileage of dashboards on EEPROM 95160 cars after 2011
Universal module, works with a large numbe..
$79.74
License 62, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
License 42, may be applicable at the discretion of the licensee (user) to the work:
Dacia Logan RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Lada Largus FL RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, E..
$79.74
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
License 04, may be applicable at the discretion of the licensee (user) to the work of:
Suzuki Swift Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Kizashi Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Grand Continental VDO Reading/EEPROM ..
$66.45
The module is designed to work with ECU Delphi MT38, Delphi MT86, supported reading (where possible), recording, checking and correction checksums. MT38 available for work in BSL mode.
2.7L, 3.3L, 3.8L (MT38/CAN) [WR/CK]
2.7L, 3.3L (MT38/K-Line) [RD/WR/CK]
2.7L, 3.3..
$93.03
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.74
The module is designed to build, edit and compare an extended error mask according to the OBD/SAE standard for SUBARU car firmware with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). The module allows you not only to turn off, but to turn back the DTC error code.
..
$39.87
Distribution of licenses after 06/14/2024
License 144, may be applicable at the discretion of the licensee (user) to work with:
ABS ECU on MK NXP Cortex M4 (FS32K144HFMLL) installed on Lada Racing, Lada Granta FL cars from 2024.
Identification
Reading/..
$159.47
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
License 46, may be applicable at the discretion of the licensee (user) to the work:
Skoda Octavia A7 03.2014 Reading/KM record
Audi A3 2012...06/2014 Reading/KM record
Seat Leon 2012...06/2014 Reading/KM record
VW Golf 7 2012...06/2014 Reading/KM record
W..
$332.24
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$492.48
License 32, may be applicable at the discretion of the licensee (user) to the work:
Chery Kimo Read/Write EEPROM, Read/Write KM (Adapter J2534)
Chery Amulet Read/Write EEPROM, Read/Write KM(KLine)
Chery Tiggo ver 1 Read/Write EEPROM, Read/Write KM(KLine)
Chery Fora Read/..
$66.45
License 137 may be applicable at the discretion of the licensee (user) to work with:
TCM ECU automatic transmission 6L50 installed on UAZ Patriot vehicles.
Identification
Reading/Clearing the DTC
Reading/VIN entry
FLASH recording(calibration area)
T..
$132.89
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 143, may be applicable at the discretion of the licensee (user) to the work:
with instrument panels on the MK Artery Cortex M4 (AT32F403) installed on Lada Granta and Lada Niva cars from 2024.
Identification
Reading/Clearing the DTC
Reading/KM Record
..
$79.74
This module allows you to make chip-tuning BMW MS42 ECU (engine MT52TU, Serie 3 E36, 5 E39 Serie) and MS43 (E46 Serie 3, Serie 5 E39, X5 E53). The module works in conjunction with ChipTuningPRO 7 or higher. The ECU programming is done using the loader CombiLoader.
Maps contain more than 150 c..
$93.03
License 70, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Full Flash file, read in BSL mode or by a programmer.
Wor..
$106.32
Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/butto..
$79.74
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.8 ECU. More than 900 calibrations of the M74.8 control system are available for editing, allowing virtually unl..
$159.47
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.66
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.73
Supports reading and writing of the Mazda c CPU SH7055 7058 and via J2534 interface ( only Tested with the Open port 2.0) by OBD2. Supported ECU Denso and Mitsubishi Corp. Latest restored from any state.
..
$79.74
Supports reading and writing c petrol Mazda Sky Active engines of 2.0 and 2.5, which require the ECU manufactured by Denso.
Car Mazda 6 GJ 2.5L Skyactiv-G PY3GEE000PY0B060 192 DENSO SH72543 PY3G-188K2-E OBD 33
Car Mazda 6 GJ 2.5L Skyactiv-G PY3HEG000PY0B060 192 DENSO SH72543 PY3H-18..
$66.45
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
License 43, may be applicable at the discretion of the licensee (user) to the work:
Renault Kadjar Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Megane I V Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Espace..
$79.74
Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set ..
$106.32
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
Includes all the module 1, the calibrated dual-mode firmware 6.38 M74 and map editing dual-mode firmware.
..
$106.32
Includes maps calibrations for all firmware M74, М74CAN and М74к.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the..
$53.16
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.89
Identification
Read / Write Fullflash on the table
A record of calibrations for OBD
Read errors/ clear error
Recalculation of checksum
..
$106.32
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of ca..
$66.45
The module is designed to work with ECU Mitsubishi and Denso installed with gasoline engines in vehicles Mazda with the 2019 model year. Supported read, write, review, and correction of the COP.
1.5L, 2.0L, 2.5L SKYACTIV-G P5/PA/PE/PY MY2019 (Mitsubishi) [PYFA] [RD/WR/CK]
1.5L, 2.0L..
$93.03
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Recalculation of the checksum
Supported models:
FIESTA 7(VII) 1400 TDCI Power 68
FIESTA 7(VII) 1400 TDCI Power 68
GALAXY 2000 TDCI Power 13..
$39.87
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
For owners module M75
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To ..
$46.51
Includes calibration cards for the firmware of the M86 ECU with VAZ software and the M74M ECU. As well as basic, non-calibrated dual-mode M86 (VAZ) and M74M firmware, dual-mode
firmware editing cards. The maps also contain additional calibrations of the "Extended Mix composition" for speciali..
$93.03
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports the read/write and the conversion stock firmware with base IDS (VBF) in binary form.
..
$66.45
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$66.45
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.66
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
Cable to overwrite the ECU M74 with Combiloader and ACC. module. The new version with the socket of OBD (CAN)
..
$53.16
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$239.21
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$239.21
The module is designed to work in service mode with the ECU ME9/MED9/EDC16. It supports reading and writing the built-in flash memory of the MPC556/MPC562/MPC564 microcontrollers, external flash memory and EEPROM, as well as checking and correcting CS and RSA signatures (except for the MED9 VAG E..
$239.21
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
$239.73
The module is designed to work in service mode (on the table) with Bosch transmission control units with SH725xx family microcontrollers used in ZF 8HP, VAG DQ380/381/500, MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. It supports reading, writing, checking and correcting CS in FLASH memory and rea..
$132.89
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.73
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.80
What is this system?
If You have several branches or regular customers that You make the firmware and they are interested in our product – they can get all the modules that You have, but they will not have access to the firmware, and You will keep the secret of your development. Th..
$299.66
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.61
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.74
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
$359.60
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
License 06, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
Skoda Fabia 2011 (P/N 5J0920810E) Reading/KM Recording, Reading/Write EEPROM, Read Pin
Skoda Octavia A5 2009 (P/N 1Z0920803B) Reading/KM Recording, Reading/Write EEP..
$106.32
Includes all the module 1, the calibrated dual-mode under LPG firmware M73 (all the existing software) and maps editing dual-mode firmware. So, buyers free program DoubleM73 tied to the key.
..
$59.80
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.61
The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles.
..
$106.32
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.73
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.73
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1.
Power supply.
To work CombiBox must submit the stabilized voltage..
$93.03
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.89
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
$239.73
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
License 20, may be applicable at the discretion of the licensee (user) to the work:
Mitsubishi ASX 2014+ 8100B951 (NEC 70F3529 without external EEPROM) Read/write KM, read/write eeprom
Mitsubishi ASX 2014+ 8100B961 (NEC 70F3523 without external EEPROM) Read/write KM, read/write..
$79.74
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.74
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)
Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Mar..
$239.73
License 28, may be applicable at the discretion of the licensee (user) to the work:
Kia Sportage 2016 Yazaki Reading/KM record
Kia Sportage 2017+ Yazaki Reading/KM record
Kia NEC34+24c16 2015-...
Kia Optima Reading/KM Writing, Reading/EEprom Recording
Kia Ceed Read..
$79.74
For owners module M74 6.38
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works ..
$46.51
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.74
Available only when the module M73.
Includes all the module 1, the calibrated dual-mode firmware Jan 7.2+ and map-editing dual-mode firmware.
..
$26.58
License 01, may be applicable at the discretion of the licensee (user) to the work:
Allows you to read and write the FULL Flash image 29F200/29F400.
Allows you to read/write the emulated in Flash EEPROM.
The "MAKE VIRGIN" function allows you to make the ECU "New", suitable ..
$132.89
License 05, may be applicable at the discretion of the licensee (user) to the work:
Autoliv production units
INFINEON XC2361 Reading/EEPROM recording, Flash reading, Clearing collision information via CAN.
INFINEON XC2336B Reading/EEPROM recording, Flash reading, Clea..
$79.74
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
$239.73
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
License 9, may be applicable at the discretion of the licensee (user) to the work:
Toyota NEC VDO+24C16 Corolla/Avensis/Auris 2013+ Reading/KM recording; Reading/EEPROM Entry 24C16
Toyota NEC VDO+24C16 2014+ AVENSIS / AURIS COROLLA Reading/KM recording; Reading/EEPROM Entry 24C16
..
$79.74
The module allows you to convert any serial in three-mode version. Support switching complete sets of calibrations, including identifiers and the mask of DTC. Toggle options: channel or DTV channel ДК2. Provided disabling the fuel pump (with programmable delay) and the injectors individually for ..
$79.74
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
License 37, may be applicable at the discretion of the licensee (user) to the work:
PIN reading
Reading ID keys
Reading the number of keys
List of supported ECUs:
BOSCH 17.9.11(Hyundai/Kia)
BOSCH 17.9.12(Hyundai/Kia)
..
$79.74
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.9 ECU. More than 900 calibrations of the M74.9 control system are available for editing, allowing virtually unl..
$159.47
License 23, may be applicable at the discretion of the licensee (user) to the work:
Mazda 6, CX5, CX7 2013+ Read, Write KM/ Read, Write EEPROM.
Mazda 2.3 2014+ Read, Write KM/Read, Write EEPROM.
Mazda MX5 2015+ Read, Write KM/Read, Write EEPROM.
Mazda 3 2010-2013 Read, W..
$79.74
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
$123.57
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$26.58
New car equipped with an engine 21127 with adjustable geometry intake tract.
..
$106.32
Includes maps calibrations for all versions (free map updates for new software). Works with standard (uncompressed) format. Writing a modified firmware available only via BSL mode any existing boot loader.
..
$93.03
Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any e..
$86.38
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
A special adapter to connect the control units on the table.
Performs automatic power management, and boot pins through the J2534 adapter.*
Required to read in the BSL mode for control units Bosch M7.8/ME7.8.8 and Continental SIM2K-25x/26x
* - tested and guaranteed works wi..
$53.16
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.32
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
The module is designed to delete data collision (CRASH DATA):
Toyota DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Toyota FUJITSU SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS RENESAS H8SX MCU 1725/1797 (256/512KB)
Subaru DENSO SRS MCU RENE..
$79.74
Designed for chip-tuning of cars and cars of Chinese production installed ECU BOSCH M7.8. Supports recording FLASH via the diagnostic connector. As well as reading and writing FLASH/EEPROM memory controller via BSL mode.
..
$66.45
License 35, may be applicable at the discretion of the licensee (user) to the work:
Hyundai Equus 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording, Reading/EEPROM recording
Hyundai Centennial 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording..
$79.74
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
$299.66
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
MDflasher software for odometer adjusting, to work with the immobilizer, the Airbag, and als..
$39.87
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.87
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.60
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary f..
$99.67
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.45
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.34
The module is designed to work in service mode with the ECU of the ZF 8HP Gen 3, ZF 9HP, ZF 8DT (PDK2-TC400), MB 8G (VGS3-FDCT), VAZ AMT, Renault JHQ gearboxes using TC1782, TC275 and TC277 family microcontrollers. Read and write operations of the built-in FLASH and EEPROM memory are supported wh..
$199.34
The module is designed to work in service mode "on the table" with the ECU of the VAG AQ250 (09G)/A L 750 (09D)/AL1000 (0C8), Volvo/LR/Ford AWF21, Mini GA6F21WA, Mazda AW6A-EL, VAG AQ250 (09G), AL1000 (0C8), PSA AM6-3, Isuzu AWR6B45-2, Mitsubishi V8AWG, Toyota/Lexus AE80F, Volvo AWF8F35, BMW..
$199.34
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The module allows you to view, edit, compare the firmware files of Kamaz, JAC, Foton cars with a Cummins 3.8L engine with a Continental CM2220 control unit. It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader. The module contains more than 1000..
$398.68
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.80
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
$132.89
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.87
Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
$143.84
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 8..
$66.45
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.96
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.59
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.58
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
$239.73
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.73
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
$239.73
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.73
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Available to all users free Module Jan 7.2+ module 1.
Key features:
Edit the calibra..
$33.22
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.53
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
The module for the new version of the program Chiploader NG
Module [51] Bosch MEDC17 - Bench is designed to read and write the internal memory (flash and eeprom) of the processor is Tricore ECU Bosch MEDC17 on the table without disassembling the ECU.
Detailed information ..
$258.00
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.88
The module allows you to view, edit, compare the firmware files of Foton, JAC cars with Cummins engine with the Continental CM2880 control unit.
It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader.
The module contains more than 1000 b..
$332.24
![[52] Delphi MT38 - OBD2 - BOOT](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[52] Delphi MT38 - OBD2 - BOOT")
