License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.64
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.64
The module is designed to work with ECU Bosch ME7.9.20 installed on the Nissan X-Trail T31 petrol engine volume of 2.5 L. is Supported by the record validation and correction checksums.
EFI ME7.9.20 Calibration (ST10F275 Bosch EXT/512KB) [WR/CK]
..
$66.36
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.73
1.5L dCi Delphi DCM 1.2 (ST10/512KB) [RD/WR/CK]
1.5L dCi Delphi DCM 3.4 (SH7059/1536KB) [RD/WR/CK]
1.5L dCi SID 301/303/304 (MPC562/2MB) [RD/WR/CK]
1.5L dCi SID 305/306 (TC1766/1504KB) [RD/WR/CK]
1.5L dCi SID 307 (TC1767/2MB) [RD/WR/CK]
2.3L dCi SID 309 (TC1767/2..
$92.91
Updated version of programmer XPROG-M v5.55 is intended for programming of new microcontroller and memory chip manufacturers, Motorola, Infineon, Micronas, Texas, Atmel, ST, National(CR16), M35080 and immobilizer EWS-3, CAS4 5M48H including software is protected from reading.
Authorization th..
$97.89
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.09
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.85
The module is designed to work with blocks motor control EMS3130, EMS3132, EMS3134 used in vehicles Renault, Dacia, Nissan. Supported reading and writing as control unit as a whole, and only in the area of calibration, validation and correction checksums, ability to work with files in formats oth..
$66.36
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.91
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.92
The module is designed to work with the ECU automatic transmission installed in some vehicles, the Kia/Hyundai. Supported read, write, review, and correction of the COP.
Kia/Hyundai: MG7.9.8/MEG17.9.12 Gearbox (ST10F275/TCU) [RD/WR]
TC14 Gearbox (MPC562/TCU) [RD/WR/CK]
TC60/TC..
$92.91
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.94
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.85
CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1.
Power supply.
To work CombiBox must submit the stabilized voltage..
$92.91
