The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recordin..
$265.79
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.73
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.73
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.79
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
License 24, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$106.32
License 37, may be applicable at the discretion of the licensee (user) to the work:
PIN reading
Reading ID keys
Reading the number of keys
List of supported ECUs:
BOSCH 17.9.11(Hyundai/Kia)
BOSCH 17.9.12(Hyundai/Kia)
..
$79.74
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
License 26, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash or EEPROM file, depending on the type of ECU.
Works as an edit..
$106.32
License 70, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Full Flash file, read in BSL mode or by a programmer.
Wor..
$106.32
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.32
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$132.89
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.89
License 60, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
&..
$132.89
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.87
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$93.03
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
The module is designed for chip tuning of Ford Focus 2.0, Maverick 3.0, Escape 2.3, Escape 3.0, Mazda Tribute 2.3 cars equipped with Visteon EEC-V ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (A. Teslya).
A Limite..
$106.32
License 13, may be applicable at the discretion of the licensee (user) to the work:
Reading/Clearing fault codes
Clearing collision information.
Unlocking the ECU.
Changing the ECU configuration.
Reading/VIN entry.
List of supported ECUs:
Renault SAND..
$79.74
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
License 44, may be applicable at the discretion of the licensee (user) to the work:
Read/Write FLASH processors SH7058,SH7059,R4F70580, R4F70590 (without recalculation of checksums).
Read/Write Opel EEPROM
Read/Write Mitsubishi EEPROM
Read/Write Suzuki EEPROM
Readi..
$106.32
The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb.
Currently it supports the following calibration: the ignition timing for h..
$239.73
Distribution of activation files after 01.06.2023
License 118, may be applicable at the discretion of the licensee (user) to work:
with a Bosch electric power steering on the Nec V850 70F3187 + EEPROM 95080 MK on the table or via the OBDII connector (where there is a technical ..
$66.45
License 21, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$106.32
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
$239.73
License 52, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Rec..
$132.89
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
The module is intended for operation in service mode with ECU MED17/EDC17 on the table, supports read, write full flash (except the bootloader area Bosch), eeprom blocks, checking and correction of the COP, without the need for opening. Requires direct connection to the connector of ECU J2534 ada..
$239.21
License 46, may be applicable at the discretion of the licensee (user) to the work:
Skoda Octavia A7 03.2014 Reading/KM record
Audi A3 2012...06/2014 Reading/KM record
Seat Leon 2012...06/2014 Reading/KM record
VW Golf 7 2012...06/2014 Reading/KM record
W..
$332.24
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by default. To download such firmware, you need to use only the CombiLoader loader.
Savi..
$106.32
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
$239.73
License 58, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by CONTINENTAL.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 95..
$106.32
License 38, may be applicable at the discretion of the licensee (user) to the work:
Mazda 3 Color Display (93c86) 2018-... Reading/KM record
Mazda 6 Color Display (93c86) 2016-... Reading/KM record
Mazda 6 Color Display (93c86) 2017-... Reading/KM record
Mazda CX5 Color ..
$79.74
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.32
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module is designed for chip tuning of Audi A4, A5, VW Amarok, Crafter, Passat, Transporter cars with 2.0L TDI and 2.5L TDI diesel engines.
Allows for professional chip tuning of Bosch EDC17CP20 control systems. The possibility of correctly disabling the ecology of EGR, DPF, SCR (AdBlue).
..
$199.34
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
The module is designed for chip-tuning VAG cars equipped with Magneti Marelli 7GV, for example, the VW Polo 1.6 L, VW Jetta 1.6 L, Skoda Rapid 1.6 L, Skoda Fabia 1.6 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$132.89
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
The Bosch EDC7UC31 MAZ / KRAZ / URAL module is designed for chip tuning of MAZ, KrAZ, MZKT, Ural cars and generator sets with diesel engines.
Supported firmware (software versions P766.120), module EDC7UC31 MAZ / KRAZ / URAL:
P766_120_MAZ_YAMZ-650_C_14_w_o_Cr_Ct
..
$265.79
Module DL501 designed for chip-tuning VAG cars (Audi and other vehicles VAG with longitudinal engine).
Please note:
Modules a third-party developer! Technical support from the author of the module (V. Kulikova).
Modules are independent from each other and are ..
$132.89
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
Module DQ250 is designed for chip-tuning VAG cars equipped with automatic transmissions DSG6 DQ250 Rev. C/E/F(02E), MQB(0D9).
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Supported versions of DQ250 ON:
..
$132.89
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5, for example, VW Tiguan 2.0 L TSI, VW Passat B6 1.8 L, Skoda Oktavia 1.8 L TSI, Audi A4 1.8 L TFSI, Seat Altea, Skoda Yeti 1.8 L TSI, etc..
Please note:
Third-party module developer! Technical suppo..
$159.47
License 10, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the EEPROM file.
Works as an editor.
List of supported ECUs:
..
$132.89
License 18, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM recording via OBDII.
Reading/FLASH recording via OBDII.
The module only works with panels on MK 9S12XHZ256.
List of supported cars:
Nissan Qashqai 2010+
..
$66.45
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
The module is designed for chip-tuning diesel cars fitted with Continental SID807:
Citroen C3 1600 HDi
Citroen C3 Picasso 1600 HDi
Citroen C4 1600 HDi
Citroen C4 Grand Picasso 1600 HDi
Citroen C5 1600 HDi
Citroen DS3 HDi 1600
Citroen DS4 HDi 1600
..
$132.89
License 01, may be applicable at the discretion of the licensee (user) to the work:
Allows you to read and write the FULL Flash image 29F200/29F400.
Allows you to read/write the emulated in Flash EEPROM.
The "MAKE VIRGIN" function allows you to make the ECU "New", suitable ..
$132.89
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$239.21
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
The module is designed for chip tuning Hyundai Santa Fe, Hyundai Tucson, KIA Carnival, KIA Sorento Prime, KIA Sportage diesel engines 2.0 CRDi and 2.2 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmw..
$106.32
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.80
Module allow to make the chip tuning Hyundai/Kia with engines V6 2.7/3.3/3.8 L, equipped with ECU Delphi MT38.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delphi MT38 by means of the loader CombiL..
$132.89
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
The module is designed for chip-tuning VAG cars with engines 1.8 T, 2.0 T, equipped with Bosch MED17.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Sof..
$159.47
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.32
The module is designed for chip-tuning VAG group (VW Tiguan, Touareg) with a diesel engine capacity of 3.0 L, Bosch ECU EDC17CP14.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are st..
$132.89
The module is designed for chip-tuning VAG group diesel engine 3.0 L ECU Bosch EDC17CP44.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are stored by default in the format of SMS-Soft..
$132.89
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
The module is designed for chip tuning Hyundai(I30, I40, IX35, Santa Fe) and Kia(CEE'd, Optima, Soul, Sportage, Venga) with diesel engines 1.6 CRDi, 2.0 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Fir..
$106.32
The module is designed for chip-tuning VAG group (VW Amarok, VW Crafter, VW LT) with a diesel engine capacity of 2.0 L, ECU Bosch EDC17C54.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC..
$132.89
The module is designed for chip-tuning of automobiles in China, equipped with Bosch ME17.8.8, for example, Chery Tiggo 2.0 L, Chery Bonus (A19), Lifan X60, Lifan Solano II, etc.
Please note:
Third-party module developer! Technical support from the author of the module (KHN0..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
The module allows for chip tuning of GM cars (Chevrolet, Cadillac, etc.) equipped with an ACDelco E92 ECU, for example, Cadillac ATS 3.6L, Cadillac Escalade 6.2L, etc.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
..
$132.89
License 68, may be applicable at the discretion of the licensee (user) to the work:
1. Auto-search Mode:
Reading the mileage of HYUNDAI / KIA cars by OBDII with the MED17/EDC17 ECU.
Automatic search for the specified mileage in the EEPROM dump loaded into the program...
$106.32
The module is designed for chip-tuning of cars of the VAG group (Audi A3/A4/A5/A6/Q3/Q5/TT, Skoda Superb, VW Golf, VW Passat, VW Tiguan, etc.) with a diesel engine capacity of 2.0 L, EDC17C46 Bosch ECU.
Please note:
Third-party module developer! Technical support from the a..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$93.03
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.5, for example, VW Touran 1.4 TFSI, VW Golf IV 1.4 TSI, VW Tiguan 1.4 TSI, Skoda Superb 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$159.47
The module is designed to work with the Denso ECU with the R7F702002 microcontroller installed in Toyota and Lexus vehicles with 3.5T (V35A-FTS) and 2.4T (T24A-FTS) gasoline engines from the 2022 model year (Toyota Tundra/Tundra Hybrid/LC300/Highlander, Lexus NX350/RX350/LS500/LX600). Reading and..
$199.34
License 89, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by Delphi.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading/EEPROM Wri..
$106.32
Module DQ500 is designed for chip-tuning VAG cars (7 speed DSG, which is installed on the cars of concern VAG c a transverse engine).
Please note:
Modules a third-party developer! Technical support from the author of the module (V. Kulikova).
Modules are independent f..
$199.34
License 29, may be applicable at the discretion of the licensee (user) to the work:
Recording the mileage of dashboards on EEPROM 95040 cars before 2011
Recording the mileage of dashboards on EEPROM 95160 cars after 2011
Universal module, works with a large numbe..
$79.74
Module allow to make the chip tuning Hyundai Genesis/Equus, Kia Cadenza/Quoris/Sorento Prime engines 3.3/3.8/5.0 l, equipped with ECU Delphi MT86.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delph..
$132.89
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.45
The Bosch EDC17C64 GAZ module is designed for chip tuning of GAZ group cars with VAG 2.0TDi diesel engines.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
The firmware of the Bosch EDC17 family controllers ..
$106.32
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Recalculation of the checksum
Supported models:
FIESTA 7(VII) 1400 TDCI Power 68
FIESTA 7(VII) 1400 TDCI Power 68
GALAXY 2000 TDCI Power 13..
$39.87
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
$132.89
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.45
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
License 50, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
License 33, may be applicable at the discretion of the licensee (user) to the work:
VW Polo (P/N 6RF920860Q) Reading/KM record
Not all software versions may be supported.
..
$79.74
License 04, may be applicable at the discretion of the licensee (user) to the work of:
Suzuki Swift Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Kizashi Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Grand Continental VDO Reading/EEPROM ..
$66.45
License 05, may be applicable at the discretion of the licensee (user) to the work:
Autoliv production units
INFINEON XC2361 Reading/EEPROM recording, Flash reading, Clearing collision information via CAN.
INFINEON XC2336B Reading/EEPROM recording, Flash reading, Clea..
$79.74
License 63, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
NEC + 24C64 06/2010+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64 06/2012+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64..
$199.34
License 45, may be applicable at the discretion of the licensee (user) to the work
Reading/KM record
Reading/FLASH recording (program and calibration area)
DFLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
License 42, may be applicable at the discretion of the licensee (user) to the work:
Dacia Logan RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Lada Largus FL RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, E..
$79.74
License 34, may be applicable at the discretion of the licensee (user) to the work:
Renault Megane III Reading/KM Recording ,Reading/EEPROM recording in the ABS/CDC/ESP blocks of the ATE manufacturer
Renault Laguna III Reading/KM Recording ,Reading/EEPROM recording in the ABS/C..
$159.47
License 11, may be applicable at the discretion of the licensee (user) to the work:
Renault MeganIII/Scenic III/Fluence/ClioIII/Modus
Restores the eeprom Eur dump (EPS), makes it "new" - ready for installation on the car.
Identification of the ECU.
Read..
$106.32
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.32
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$93.03
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
License 20, may be applicable at the discretion of the licensee (user) to the work:
Mitsubishi ASX 2014+ 8100B951 (NEC 70F3529 without external EEPROM) Read/write KM, read/write eeprom
Mitsubishi ASX 2014+ 8100B961 (NEC 70F3523 without external EEPROM) Read/write KM, read/write..
$79.74
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.74
License 06, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
Skoda Fabia 2011 (P/N 5J0920810E) Reading/KM Recording, Reading/Write EEPROM, Read Pin
Skoda Octavia A5 2009 (P/N 1Z0920803B) Reading/KM Recording, Reading/Write EEP..
$106.32
Supported reading (where possible), write via OBD and correction KS for vehicles with engines of 1.1, 1.4, 1.6 liters.
Kia/Hyundai: 1.4L, 1.6L (ME17.9.11/12/13) [RD/WR/CK]
Kia/Hyundai: 1.4L, 1.6L (ME(G)17.9.21/17.9.21.1) [RD/WR/CK]
Kia/Hyundai: 1.6L, 3.0L (ME17.9.2/ME(D)(G)17...
$93.03
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the abi..
$79.74
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
The module is designed to work with ECU Simos 8.1, 8.2, 8.3, 8.4, 8.5, 8.6, 10, 11, 12, PCR 2.1. Supported reading (read or virtual), the entry (with or without unlocking), verification and correction of the COP.
2.8 L V6 FSI (SIMOS8.1) [RD/WR/CK]
3.2 L V6 FSI (SIMOS8.2) [RD/WR..
$159.47
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
Allows you to work with Renault Clio/Megane/Scenic/Logan, equipped with systems Sirius32/EMS3132/Sirius34/EMS3134. ECU programming directly on the vehicle through the diagnostic connector. The main difference from similar applications is the ability to read/write programs for a replacement.
I..
$66.45
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.89
The module is designed to work with ECU Denso installed on vehicles JLR. Supported read, write, review, and correction checksums.
Jaguar XF/XJ/XK (X250/X350/X351/X150) 3.0L V6, 3.5L V8, 4.2L V8/SC (Denso) [RD/WR/CK]
Range Rover/Sport/Discovery 3 4.0L V6, 4.4L V8, 4.2L V8/SC (Denso) ..
$119.61
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
The module is designed for chip tuning of Hyundai Starex, Porter, HD78, i30, KIA Bongo and others cars with 2.5CRDI diesel engines, Delphi DCM 3.7 ECU.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
Supported software versions:..
$132.89
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.74
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.89
The module is designed to work with ECU Delphi MT38, Delphi MT86, supported reading (where possible), recording, checking and correction checksums. MT38 available for work in BSL mode.
2.7L, 3.3L, 3.8L (MT38/CAN) [WR/CK]
2.7L, 3.3L (MT38/K-Line) [RD/WR/CK]
2.7L, 3.3..
$93.03
The module is designed for operation with control units petrol engines and turbo diesel installed in vehicles Land Rover Freelander 2, Evoque, Discovery Sport etc. Supported read, write, calibration, validation and correction of the COP.
Discovery 3 2.7L TDV6 (SID201/SID204) [RD/WR/CK]
..
$159.47
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.66
The Bosch MD1CS001 (DDE802L, DDE803S) BMW module is designed for chip tuning of BMW cars with B47D20xx diesel engines. Installed on:
3rd G20 Series
5th series G30 and G31
X3 Series G01
X4 Series G02
Pay attention:
A third-party developer module! Tech..
$332.24
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A.
..
$359.60
The module is designed to work with Bosch ECU installed in the Honda cars. Supported ECU MED17.9.3, EDC17C58 (write after unlocking in BSL) as well as EDC17CP06, EDC17CP16 (recording without unlocking).
PGM-FI (Bosch EDC17CP06/EDC17CP16/2MB) [WR/CK]
PGM-FI (Bosch EDC17CP50/4MB) [Unl..
$93.03
The module is designed to work with the ECU EDC7/EDC16/EDC17 diesel engines Mitsubishi Fuso Canter. Supported read, write, review, and correction of the COP. For some cars with ECU EDC7/EDC16 for writing may require a direct connection to the connector block.
Fuso Canter (EDC7C4-6/EDC16C3..
$132.89
The module is designed to work with ECUS that are installed in vehicles with Ford diesel engines 1.4, 1.5, 1.6 l Supported read, write, review, and correction checksums.
Ford Focus 3: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
Ford Mondeo 4: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
..
$93.03
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.73
1.5L dCi Delphi DCM 1.2 (ST10/512KB) [RD/WR/CK]
1.5L dCi Delphi DCM 3.4 (SH7059/1536KB) [RD/WR/CK]
1.5L dCi SID 301/303/304 (MPC562/2MB) [RD/WR/CK]
1.5L dCi SID 305/306 (TC1766/1504KB) [RD/WR/CK]
1.5L dCi SID 307 (TC1767/2MB) [RD/WR/CK]
2.3L dCi SID 309 (TC1767/2..
$93.03
The module is designed to work with ECU EDC17 installed with a diesel engine 6.7 l in the Ford. Supported read, write, review, and correction of the COP.
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [BC3A] [RD/WR/CK]
Ford Truck: 6.7L Power Stroke V8 (EDC17CP05) [DC3A/FC3A] [RD/WR/CK..
$132.89
License 43, may be applicable at the discretion of the licensee (user) to the work:
Renault Kadjar Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Megane I V Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Espace..
$79.74
The module is designed to work with the ECU SID208 installed on vehicles with diesel engine 2.2 l Supported read, write, razblokirovka the ECU to record the modified firmware, and test and correction checksums.
Citroen/Peugeot 2.2 L HDi (SID208) [WR/CK] (write after unlocking in BSL)
..
$93.03
The module is designed to work with blocks of variable-speed drives and automatic transmission that are installed on Mitsubishi vehicles, supported by reading and writing.
CVT Lancer X/ASX 1.8/2.0L, Outlander XL/3 2.0/2.4L (MH8104F/512KB MH8106F/1MB) [RD/WR/CK]
AT Pajero Sport (2010..
$132.89
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
The module is designed to work with blocks motor control EMS3130, EMS3132, EMS3134 used in vehicles Renault, Dacia, Nissan. Supported reading and writing as control unit as a whole, and only in the area of calibration, validation and correction checksums, ability to work with files in formats oth..
$66.45
The module is designed for operation with control units EDC15C7, EDC16CP34 and EDC16C39, supported reading and writing of calibration on K-line and the record as a whole on the CAN bus (supports basic BDM format and the format of GDS), verification and correction checksums.
2.0 L, 2.5 L C..
$66.45
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
The module is designed to work with the Bosch ECU automatic transmission 6HP, 8HP a / m JLR through the diagnostic connector of cars. Supported read, write, check checksum correction:
ZF 6HP26/6HP28 TCM (MPC5xx/TC1766) [RD/WR/CK]
ZF 6HP28 Continental TCM (TC1766) [AH42-Ax] [R..
$119.61
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.73
The module is designed to work with the ECU 6DCT450 transmission installed in the Ford/Volvo/JLR. Supported read, write, clone the ECU.
PowerShift TCM (6DCT450) [RD/WR]
PowerShift 6DCT450 Boot (MICRO) [RD/WR]
PowerShift 6DCT450 Boot (EEPROM) [RD/WR]
PowerShift 6DCT451 TC..
$132.89
Module supported:
Read/erase error codes
Verification and recalculation of the checksum (CS)
Identification
Entry
Reading
For the following ECU's:
BRZ SH72531 [1280k] CAN 2013+
SH7058 [1024k] CAN 2007+
SH7058 [1024k] K-line 2003+
SH7..
$106.32
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.73
The module is designed to work with ECU Bosch EDC17CP27/EDC17C49/EDC17C79 installed on vehicles of Jeep. Supported read, write, review, and correction checksums.
2.8 L CRDI (EDC17CP27)[RD/WR/CK]
3.0 L CRDI (EDC17C49/C79) [RD/WR/CK] read-may require direct connection to the ECU
..
$93.03
The module is designed to work with a DC4 transmission control UNIT, installed in the cars of Renault. Supported read, write, review, and correction of the COP.
EDC DC4 Gearbox (TC1766/1506KB) [RD/WR/CK]
EDC DC0/DC4 Gen2 (DKG250 Gen2) (TC1784/2560KB) [RD/WR]
..
$66.45
Module supported:
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
Reading/erasing fault
Read/write EEPROM
Recalculation of checksum
..
$66.45
The module is designed to work with the ECU built on microcontrollers SH72513/SH72543/SH72544 installed on diesel vehicles of different brands. Supported read, write, and recalculation of checksums.
Kia/Hyundai 2.5 L CRDI (DCM3.7AP) [RD/WR/CK]
Opel/Chevrolet 2.0 L, 2.2 L CDTI (DCM3...
$132.89
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
The module is designed for operation with control units SIMK-41/43, SIM2K-47 used in vehicles Kia/Hyundai. Supported reading (when available), entry, checking and correction of the checksum, automatically detect the type of ECU.
2.0 L, 2.7 L K-Line (SIMK-41/43) [RD/WR/CK]
2.0 L, 2.4..
$66.45
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$239.21
The module is designed to work with ECU Mitsubishi and Denso installed with gasoline engines in vehicles Mazda with the 2019 model year. Supported read, write, review, and correction of the COP.
1.5L, 2.0L, 2.5L SKYACTIV-G P5/PA/PE/PY MY2019 (Mitsubishi) [PYFA] [RD/WR/CK]
1.5L, 2.0L..
$93.03
The module is designed to work with ECU Bosch MED17.7.1/MED17.7.2/MED17.7.5/MED17.7.3/MED17.7.3.1, EDC17CP01/EDC17CP10 (with external flash), EDC17CP46/EDC17CP57/EDC17CP60/EDC17C66 installed on vehicles from Mercedes-Benz and Infiniti some. Supported reading (only for blocks EDC17), entry, valida..
$159.47
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
The module is designed to work with the ECU engine 1.0 TSI, 1.2 TSI, 1.4 TSI, 1.6 MPI, 2.0 TSI, 3.6 FSI, 1.0 MPI, etc. installed on vehicles group VAG (VW Golf 7, Polo, Passat B8, Skoda Rapid, Octavia A7, Tiguan, Jetta, Audi A1, A3, etc.). Supported entry, verification and correction of the COP.
..
$119.61
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set ..
$106.32
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
The module is designed to work with the ECU EMS3155, SID309, Hitachi CPU RH850 working on the UDS Protocol and installed in vehicles with petrol engines 1.2 l and diesel 1.5 l Supported read, write, review, and correction checksums.
1.2 T EMS3155 UDS (TC1782/2.5 MB) [RD/WR/CK]
1.5 L..
$132.89
The module is designed to work with the ECU Kefico/Denso processor SH72546 installed in cars with a diesel engine of 2.5 l, standards of toxicity Euro-6. Supported read, write, review, and correction checksums.
Kia/Hyundai 2.5L CRDI (SH72546) [RD/WR/CK]
Hyundai Euro 5 (Denso SH7058S..
$93.03
The module is designed to work with the ECU from diesel engines 1.6, 2.0, 3.0 and 4.2 TDI are installed on passenger cars and crossover vehicles group VAG, approximately 2010. Supported entry, verification and correction of the COP.
2.0L, 3.0L TDI (EDC17CP04/EDC17CP14/EDC17CP..
$119.61
The program in Russian and English languages.
Universal programmer a large number of microcontrollers from Microchip, Atmel, Cypress, ST, etc., and also chip FLASH/EEPROM (currently more than 13000 chips). Connect to PC and power to the programmer through the USB port of the computer (5v).
..
$122.08
The module is designed to work with blocks EDC16C39, which are installed on vehicles UAZ Patriot, hunter with diesel engines ZMZ and Iveco. Supported reading calibrations (for Iveco), a record full of files (and calibration for the Iveco), verification and correction checksums.
Patriot/Hu..
$66.45
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
Toyota Camry, Rav4 cars with 2.4L 2AZ-FE petrol engines
Supported versions:
89663-02802-
89663-02822-
89663-06431-
89663-33021-
89663-33041-
89663-33691-
89663-33701-
89663-33702-
89663-33720-A
89663-33721-
..
$39.87
Toyota Camry, Highlander, and Lexus cars with 2GR-FE 3.5l gasoline engines
Supported BY:
89663-06772- 89663-06G70- 89663-06P00- 89663-0E050-A 89663-0E340- 89663-22290-A 89663-30A11- 89663-33340-A 89663-33341- 89663-33640-A 89663-33641- 89663-33642- 89663-33650-A 8966..
$39.87
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.74
The China EDC17CV44 Truck module allows you to view, compare and edit firmware files of FAV cars, Shacman trucks, MAZ, Yutong, etc. with a WP7, KR10, WP12 engine with an EDC17CV44 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection pha..
$332.24
Toyota Corolla cars with 1ZR-FE, 3ZZ-FE 1.6 petrol engines
Supported software:
89663-02240-A
89663-02241-
89663-02270-A
89663-02482-
89663-02483-
89663-02491-
89663-02492-
89663-02502-
89663-02503-
..
$39.87
Toyota Denso Petrol 5.7i module for chip tuning of Toyota Sequoia, Tundra, Lexus LX570, etc. with 5.7-liter 3UR-FE and 3UR-FBE engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the authors of the module (V. Kulikova and A. Tesla).
..
$239.21
The Bosch EDC7UC31 KAMAZ module is designed for chip tuning of KAMAZ vehicles with diesel engines of the KAMAZ-740 family.
Supported firmware (software versions P702.141, P986.310), EDC7UC31 KAMAZ module:
702V141_740.60-360-290812_5460-4010142-01
702V141_740.60-360-29..
$265.79
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.18
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.73
The module is intended for read-write FLASH/EEPROM ECU Bosch MEDC17 series without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
Module is the automatic correction of the COP while recording.
..
$199.34
The module is designed to work with ECU Bosch ME7.9.20 installed on the Nissan X-Trail T31 petrol engine volume of 2.5 L. is Supported by the record validation and correction checksums.
EFI ME7.9.20 Calibration (ST10F275 Bosch EXT/512KB) [WR/CK]
..
$66.45
The module is designed to work with blocks motor control EDC16CP31-6 and EDC16CP31-8, installed in the vehicles of MB Sprinter 906/909 (Classic). Supported read, write, calibration, validation and correction of the COP.
Sprinter (906) CDI 2.2 L (EDC16CP31-6) [RD/WR/CK]
Sprinter Clas..
$93.03
The module allows you to produce a professional chip tuning for Renault Logan and Renault Sandero 2 2 that equipped with ECU Continental EMS3120.
Supported IDs firmware module Logan/Sandero:
HW4319R_SW4234R_4541R
HW4319R_SW4234R_4928R
HW4319R_SW4234R_4929R
HW4319R_SW..
$106.32
The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector.
Is free app for all users 2 or 3 version of module BSL TC17xx J2534.
Module Bosch MEDC17 Hyundai/Kia supported the following types of EC..
$106.32
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
Allows you to edit and compare the error mask on a large number (about 1000) of Denso software. The module allows you not only to turn off, but to turn back the DTC error code.
Supported Software:
89663-01032- 89663-01121- 89663-02023- 89663-02161- 89663-02162- 89663..
$39.87
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
$599.33
The Toyota Denso Diesel 4.5D (1VD-FTV) module with 76F0070 processor is designed for chip tuning of Toyota cars with 4.5L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported..
$239.21
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
The module is designed to work with ECU Bosch ME(D)17/EDC17 working on CAN Protocol TP2.0/K-Line. Supports recording via the diagnostic connector modified firmware, validation and correction checksums. Supported ECU MED17.1/17.1.1, ME(D)17.5/17.5.1/17.5.2/17.5.5/17.5.6/17.5.20, EDC17U01/U05, EDC1..
$119.61
The module allows you to produce a professional chip tuning Lada Largus cars equipped with ECU Continental EMS3120.
Supported firmware versions:
HW7908R_SW09350_90047
Features of the module:
The possibility of open firmware (FullFlash only) in BIN format or SMS-Soft Cont..
$106.32
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
The Toyota Denso Diesel 3.0D (1KDFTV) module with 76F0040GD, 76F0039AGD, 76F0070, 76F0085 processors is designed for chip tuning of Toyota cars with 3.0L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the modul..
$239.21
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7055S/512KB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2003+ K-Line (SH7058/1MB) [RD/WR/CK]
2.5L, 3.0L, 2.0T, 2.5T Denso 2007+ CAN-bus (SH7058S/1MB) [RD/..
$119.61
VW Touran, Golf, Passat, Transporter, Caddy cars with engines AVQ,BKC,BMT,BLS, etc. with a volume of 1.9L
Supported Software:
1037367485P379U6FP
1037368205P213U6FT
1037370254P213U8C3
1037370811379U85B6
1037371094379U85B6
1037371250379U85B6
..
$39.87
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
$239.73
Toyota Land Cruiser 150 cars with 1GD-REV diesel engine Cost: 3000r.
Supported Software:
89663 - 60X23
89663 – 60X24
89663 – 60X26
89663 – 60X27
89663 – 60X28
89663 – 60X29
89663 – 60Z31
89663 – F0594
89663 – F0595
89663 – F0599
..
$39.87
Toyota Camry, Rav4, Avensis cars with gasoline engines 1AZ-FE, 3ZR FAE, 3ZR-BE, 3ZR-FE, volume 2.0
Supported software:
89663-05A11-
89663-06460-
89663- 06B40-
89663-06E10-
89663-42053-
89663-42192-
89663-42590-
89663-42600- Ah
..
$39.87
The modules are designed to read / write the FLASH/EEPROM of the ECU series Bosch EDC7/EDC16/PSG16/ME9 without opening.
The module requires a connection to the ECU with adapter J2534 DiaLink or Scanmatik-2 (2 PRO). Check the documentation for details.
The module does not s..
$199.34
License 49, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
..
$132.89
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$66.45
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
The module does NOT checksum when you save the firmware.
Supported firmware versions:
14CE5A_F4KH1DQGNV1-20161015-130049 — Nissan X-trail T32 2.0 144hp 2015 AT
14C..
$159.47
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
The module allows you to produce a professional chip tuning for Renault Logan, Renault Sandero, Nissan Almera engine 1.6 L, automatic transmission, equipped with ECU Continental/Siemens EMS3134.
Supported versions:
REA820
REA830
Features of the module:
The possibil..
$79.74
This module allows you to work on the car via the OBDII connector with the Visteon ECU installed on Ford cars.
Module Functions:
Identification Reading
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalculation of calibration area c..
$66.45
The Toyota Denso Diesel 2.8D module supports all software versions, including GEN3; processors D76F0196F1 (1536Kb), D76F0219F1 (2048kB), R7F701202 (4096Kb). Designed for chip tuning of Toyota cars with 2.8L diesel engines, Denso ECU.
Pay attention:
Third-party developer mod..
$239.21
The Toyota Denso Diesel 2.5 module is designed for chip tuning of Toyota cars with 2.5 diesel engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
Supported software versions, Toyota Denso Die..
$239.21
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
License 53, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to read and write a full memory image (FULL FLASH) for cloning the ECU.
List of supported ECUs:
Simtec 71.5
Simtec 71.6
Simtec 75.1
Si..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$212.63
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$66.45
License 31, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
It only works with the full firmware version (FULL FLASH..
$106.32
License 08, may be applicable at the discretion of the licensee (user) to the work:
The work is done by upgrading the Flash file.
Works as an editor.
DENSO engine control units on NEC 76F00xx processors with firmware size are supported 256, 320, 368, 384, 496, 736, 992, 1024.
..
$79.74
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.74
Includes maps calibrations for all firmware M74, М74CAN and М74к.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the..
$53.16
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
$239.73
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
$359.60
The Bosch EDC7UC31 GAZ module is designed for chip tuning of GAZ and MAZ cars with YAMZ-5344.20, YAMZ-53416, YAMZ-53441.20, YAMZ-53442, YAMZ-536, YAMZ-53601, YAMZ-53602, YAMZ-53603, YAMZ-53613, YAMZ-53622, YAMZ-53623, YAMZ-53624, MMZ-245 diesel engines.7.
Supported firmware (softwa..
$265.79
Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/butto..
$79.74
The Ford EDC17CV41 module 24 allows you to view, compare and edit firmware files of Ford Cargo F-Max vehicles (Bosch EDC17CV41 ECU).
Calibrations are available for editing: boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phases, torque limits, ..
$398.68
This module allows you to work on a car via an OBDII connector with Siemens ECM installed on Ford cars.
OBD II Mode (working on a car or on a desk):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalcula..
$66.45
The module is designed to work in service mode (on the table) with Bosch transmission control units with SH725xx family microcontrollers used in ZF 8HP, VAG DQ380/381/500, MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. It supports reading, writing, checking and correcting CS in FLASH memory and rea..
$132.89
The module is designed for chip tuning of Ssang Yong Actyon, Korando, Rexton, Rodius, Stavic, etc. cars with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulik..
$132.89
The module is designed for chip tuning of Suzuki Jimny, Liana, Grand Vitara, Swift, SX4 cars with 1.3L, 1.5L, 1.6L, 2.0L, 2.4L engines equipped with Denso ECU with SH7055 and SH7058 processors.
Pay attention:
A third-party developer module! Technical support from the author..
$79.74
Reading(slow)/Entry of the calibration Can
Read/Delete errors
Check/Fix the checksum
Virtual reading
Supported units EDC17C08 and EDC17CP14 with any TPROT
..
$66.45
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.89
Updated version of programmer XPROG-M v5.55 is intended for programming of new microcontroller and memory chip manufacturers, Motorola, Infineon, Micronas, Texas, Atmel, ST, National(CR16), M35080 and immobilizer EWS-3, CAS4 5M48H including software is protected from reading.
Authorization th..
$97.89
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.33
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to v..
$51.83
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.74
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.74
License 109, may be applicable at the discretion of the licensee (user) to the work:
via the OBDII connector or on a table with 6RF(U)92086x instrument panels(white indication) based on the 70F3524 microcontroller without an external EEPROM installed on VAG Polo cars since 2014, wh..
$199.34
Distribution of activation files after 11/30/2022
License 98, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode (Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading..
$106.32
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.89
The module is designed to work through the diagnostic connector of a car with Delphi DCM6.2 engine control units used in VAG concern cars. Virtual reading, writing, checking and correction of checksums are supported.
1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/RD/WR/CK]
..
$132.89
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.87
The module is designed for chip tuning of VAG cars with gasoline engines 1.8TFSI and 2.0TFSI of the third generation: Audi A4/ A5 / A6, Audi Q3 / Q5, Audi TT, Porsche Macan, Skoda Octavia, Skoda Octavia RS, VW Passat, VW Polo GTI, VW Jetta, VW Tiguan, etc.
Note:
Third-party mod..
$239.21
The module is designed for chip tuning Hyundai(IX35, IX55, Santa Fe, Tucson) and Kia(Carnival, Mohave, Sorento, Sportage) with diesel engines 2.0 CRDi (D4HA, 184HP), 2.2 CRDi (D4HB, 197HP) and 3.0 V6 CRDi (D6EB, 247HP).
Please note:
Third-party module developer! Technical s..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.89
The cars of Chinese production (Great Wall Hover, BYD, etc.) with Delphi MT20U ECU, MT20U2, MT20UED, MT22U and MT22.1. Supported read and write FLASH and EEPROM.
..
$93.03
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Read/Write calibration by K line
Record calibration + program Can
Read/Delete errors
Check/Fix the checksum (fake digital signatures)
Supported units EDC16C39-5.41 and EDC16CP34-5.30
..
$66.45
The module is designed for chip tuning of Geely vehicles equipped with DSI TCM automatic transmission.
Module Features:
Limited module with a limited number of calibrations!
The module calculates the COP.
Hardware versions 02F and 02R are supported.
Suppor..
$93.03
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
The module is designed for chip tuning of Chevrolet Captiva, Cruze, Orlando, Daewoo Winstorm, Opel Antara, etc. with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kuli..
$132.89
The module is designed for chip tuning of Great Wall Hover cars and others with 2.0 TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported software versions:
&..
$106.32
The module is designed for chip tuning of VAG cars with 1.8 TFSI and 2.0 TFSI petrol engines of the 3rd generation: Audi A4 1.8 TFSI, Audi A5 1.8 TFSI, Audi A5 2.0 TFSI, Audi A6 1.8 TFSI, Audi Q5 2.0 TFSI, Skoda Octavia 1.8 TFSI, Skoda SuperB
Pay attention:
A third-party de..
$239.21
Bosch EDC17C64 module is designed for chip tuning of Audi A3 / A4 / A6 / Q5, VW Golf7 / Sharan / Tiguan, Skoda Octavia and others with 1.6L and 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
..
$132.89
Module DQ200 is designed for chip-tuning VAG cars equipped with automatic transmission DQ200 DSG6 Rev. DQ200 (0AM), DQ200MQB (0CW), DQ200G2 (0CW).
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Supported versi..
$132.89
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
License 12, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$79.74
License 17, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording EEPROM 24c04 or 93c56 (depends on the type of panel) by OBDII or direct connection on the table (connection in the help).
Correction of odometer readings by OBDII or direct connecti..
$66.45
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
The module supports:
A quick read full dump of the processor (7058 -5 min; 7055 -2,5 min)
Slow reading, that would add ECU indiscriminately (from 50min)
The full dump of the processor (7055 -15 min; 7058 -25 min)
Recalculation of checksum
Recovery recording session..
$119.61
The Bosch MD1CP002 (DE 832) BMW module is designed for chip tuning of BMW cars with B57D30xx and B47D20xx diesel engines.
Installed on:
3rd G20 Series
5th series G30 and G31
6th Series G32
7th series G11 and G12
8th series G14, G15 and G16
X3 S..
$332.24
The module allows chip tuning of Opel, Chevrolet, Cadillac cars equipped with an ACDelco E37 ECU.
Examples of cars equipped with this type of ECU: Chevrolet Captiva (C140) 2011+, Opel Antara 2011+.
Pay attention:
A third-party developer module! Technical support from th..
$13.29
The module is designed for chip tuning of Hyundai and Kia cars with EURO-6 diesel engines equipped with Denso ECU with SH72543/SH72546 processors.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported s..
$265.79
The module is designed for chip-tuning diesel cars Ford, Peugeot and Citroen equipped with Continental SID208:
Ford Ranger 3.2 TDCI
Ford Transit 2.2 TDCI
Ford Transit 2.4 TDCI
Peugeot Boxer 2.2 HDI
Citroen Jumper 2.2 HDI
Please note:
Third-party modul..
$159.47
The module is designed for chip tuning of BMW cars with the N55B30 engine.
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by d..
$132.89
The module is designed for chip tuning of VAG group cars with gasoline engines, Bosch MG1CS001 ECU, for example:
Audi A1 2.0 TFSI
Audi A3 2.0 TFSI
Audi A4 2.0 TFSI
Audi A5 2.0 TFSI
Audi A7 2.0 TFSI
Audi Q2 2.0 TFSI
Audi Q3 2.0 TFSI
Audi Q5 2.0 TFS..
$186.05
The Nissan Denso Diesel 2.5 TDI SH7059 module is designed for chip tuning of Nissan Navara, Pathfinder, Cabstar, Murano, NV300, Caravan, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7059 processors.
Pay attention:
Third-party developer modules! Techni..
$132.89
The module allows for chip tuning of Opel, Chevrolet, Cadillac cars equipped with ACDelco E39 and E39A ECUs.
Examples of cars equipped with this ECU type: Opel Insignia 2.0L A20NHH / A20NHT (LHU), Opel Antara 2011+ 3.0L (LF1), Opel Antara 2012+ 3.0L (LF1, LFW), Opel Astra-J A16XHT / 1.6L SIDI..
$132.89
Bosch EDC17C74 module is designed for chip tuning of Audi A3 / Q2, VW Golf / Passat / Tiguan, Skoda Superb / Kodiaq and others with 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
By default, the firmwar..
$132.89
License 36, may be applicable at the discretion of the licensee (user) to the work:
Audi A3 Mk3 07.2014+ Reading/KM record
Audi Q2 Reading/KM record
Skoda Fabia III 07.2014+ Reading/KM record
Skoda Octavia III 07.2014+ Reading/KM record
Scoda Rapid 09.2015+ Reading..
$332.24
The module is designed for chip tuning of Korean-made cars of 2018 and newer with GDI gasoline engines equipped with Kefico CPEGD2.20.1 / CPEGD2.20.2 / CPEGD2.20.3 / CPGDSH2.26.1 / CPGDSH2.26.3 / CPGPSH2.14 ECUs.1.
These ECUs are used on cars such as:
Hyundai Elantra, Avant..
$265.79
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.89
The Nissan Denso Diesel 2.5 TDI SH7058 module is designed for chip tuning of Nissan Cabstar, Condor, Navara, NP300, Pathfinder, Vanette, X-Trail, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7058 processors.
Pay attention:
Third-party developer module..
$132.89
License 79, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Takata SRS units based on SPC560P34L1 processors installed on Lada Vesta and UAZ Patriot cars, which allows for full-fledged repair and restoration wor..
$66.45
Optional module for chip tuning of BMW cars with Bosch MEVD17 control units.2.4
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Contain..
$132.89
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.9 control units.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family controllers is saved in the SMS-Soft Containe..
$132.89
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
Sending activation files after 02/22/2022!
The module works with BCM manufactured by Bosch, Continental Gen.1(2 byte SeedKey), Gen.2(5 byte SeedKey).
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Readin..
$106.32
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.5
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Container File format..
$132.89
The module allows you to perform chip tuning of Chevrolet cars equipped with an ACDelco E80 ECU.
Pay attention:
A third-party developer's module! Technical support from the author of the module (KHN09).
Working with firmware that does not contain the control program c..
$159.47
The module is designed for chip-tuning, car Hyundai I40, Hyundai IX35, KIA Soul diesel engines 1.6 CRDi and 1.7 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmware families Bosch МEDC17 are stored by..
$106.32
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E78.
Examples of vehicles equipped with this type of ECU: Opel Astra J A14NET, A14NET Opel Opel Corsa C, Opel Mocca A14NET, A14NET Chevrolet Cruze, Chevrolet Tracker A18XER, Chevrolet Malibu A..
$132.89
The module is designed for chip-tuning of automobiles in China, equipped with Bosch MED17.8.10, for example, Geely Atlas 1.8 T.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored ..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.25, for example, the VW Golf 1.2 TSI, 1.4 TFSI, Skoda Octavia, Skoda Superb 1.4 TFSI, VW Jetta 1.4 TFSI.
Please note:
Third-party module developer! Technical support from the author of the module (K..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch ME17.5.26, for example, Skoda Octavia 1.6 MPI, Skoda Rapid 1.6 MPI Skoda Yeti 1.6, 1.6 MPI VW Jetta, VW Polo 1.6.
Please note:
Third-party module developer! Technical support from the author of the module (..
$159.47
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
Additional module for chip tuning Peugeot with the control units Bosch MEVD17.4.2.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Containe..
$132.89
Module MM4HV designed for chip-tuning VAG cars equipped with Magneti Marelli 4HV, for example, VW Polo 1.4 L, VW Jetta 1.4 L, 1.4 L Skoda Rapid, Skoda Fabia 1.4 L.
Please note:
Modules a third-party developer! Technical support from the author of the module (KHN09).
Read and wri..
$132.89
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.32
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.2, for example, VW Passat 1.8 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the f..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.21, for example, the VW Golf 1.4 TSI, Skoda Octavia 1.2 TSI, Audi A3 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch М..
$159.47
License 138, may be applicable at the discretion of the licensee (user) to work with:
ECU EGS gasoline engines installed on UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(full content)
FLASH recording (control program + calibration area or ..
$66.45
License 99, may be applicable at the discretion of the licensee (user) to the work:
1. OBDII Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculation of checksums)
..
$106.32
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.3 and MT22.5.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$119.61
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU p..
$119.61
License 19, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording KM by OBDII.
Reading/Recording HERPROM by OBDII.
Reading FLASH by OBDII.
Nissan/Infiniti cars from 2011 and above with the Continental VDO NEC 34+24C16 dashboard are sup..
$79.74
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.74
Adapter for working with microcontrollers with the M&Dflasher program.
The following pins are present on the board:
VDD
FV
PWR
A1
A2
GND
RST
MD0
MD1
TX
RX
RTX
The voltage levels 3.3V and 5V are supp..
$69.11
License 90, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
License 77, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (..
$106.32
License 74, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
The module is designed to work with the ECU automatic transmission installed in some vehicles, the Kia/Hyundai. Supported read, write, review, and correction of the COP.
Kia/Hyundai: MG7.9.8/MEG17.9.12 Gearbox (ST10F275/TCU) [RD/WR]
TC14 Gearbox (MPC562/TCU) [RD/WR/CK]
TC60/TC..
$93.03
License 62, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.73
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
$239.73
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
License 41, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the ACDelco E83 ECU in OBD II Mode, Bench Mode and Recovery mode.
1. OBDII Mode(Car operation):
Reading Identification
Reading Er..
$106.32
License 39, may be applicable at the discretion of the licensee (user) to the work:
Subaru Outback 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Subaru Legacy 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Not all software versions may be supporte..
$79.74
License 40, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of the calibration area (with recalculation of checksums)
..
$106.32
License 02, may be applicable at the discretion of the licensee (user) to the work:
Continental SID 305 Reading/KM record
Continental SID 306 Reading/KM record
Continental SID 307 Reading/KM record
Continental SID 309 Reading/KM record
Delphi DCM3.4 Reading/KM reco..
$106.32
License 9, may be applicable at the discretion of the licensee (user) to the work:
Toyota NEC VDO+24C16 Corolla/Avensis/Auris 2013+ Reading/KM recording; Reading/EEPROM Entry 24C16
Toyota NEC VDO+24C16 2014+ AVENSIS / AURIS COROLLA Reading/KM recording; Reading/EEPROM Entry 24C16
..
$79.74
License 23, may be applicable at the discretion of the licensee (user) to the work:
Mazda 6, CX5, CX7 2013+ Read, Write KM/ Read, Write EEPROM.
Mazda 2.3 2014+ Read, Write KM/Read, Write EEPROM.
Mazda MX5 2015+ Read, Write KM/Read, Write EEPROM.
Mazda 3 2010-2013 Read, W..
$79.74
License 16, may be applicable at the discretion of the licensee (user) to the work:
ECU on the MB96F386+95160 microcontroller
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording(program area + calibration)
..
$79.74
The module is designed to work with the CRD3/CD3 ECU installed in Mercedes Benz cars. Work is supported through the diagnostic connector and "on the table". Supports reading, writing, checking and correcting checksums. It is possible to clone the ECU.
Mercedes-Benz CRD3/CRD3P FLASH [RD/WR..
$93.03
License 115, may be applicable at the discretion of the licensee (user) to the work:
providing advanced functionality - working with instrument panels via the OBD II connector (where there is a technical possibility), installed on Hyundai/Kia cars since 2018, which allows for full-..
$79.74
License 108, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS Siemens W3, Siemens VW51, Siemens VW52 units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data:
..
$66.45
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.32
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.32
License 85, may be applicable at the discretion of the licensee (user) to the work:
Correction of mileage readings with recalculation of checksums in the read EEPROM area of the processor firmware,
in DSG DQ200, DSG DQ200_MQB, DSG DQ200 G2, DSG DQ250 E/F(02E) units installed on..
$79.74
License 82, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars Nissan / Infiniti, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.74
License 80, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on Ford/Mazda cars,
which allows for full-fledged repair and restoration work with ECU d..
$79.74
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.74
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.47
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.89
License 35, may be applicable at the discretion of the licensee (user) to the work:
Hyundai Equus 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording, Reading/EEPROM recording
Hyundai Centennial 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording..
$79.74
License 76, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording of the Flash memory of the ECU of the transmission of VAZ cars through the diagnostic connector or on the table (connection is available in the online help).
..
$66.45
License 75, may be applicable at the discretion of the licensee (user) to the work:
Reading/FullFlash Entry
Reading/EEPROM recording
The ability not to overwrite the boot sector.
The module allows you to use your Seed Key, in case it was replaced with a non-s..
$106.32
License 59, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
D70F3230 -D70F3231 -D70F3232 -D70F3233 -D70F3234 -D70F3235 -D70F3236 -D70F3237 -D70F3238 -D70F3239 -D70F3333 -D70F3334-D70F333..
$66.45
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.74
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.32
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
License 32, may be applicable at the discretion of the licensee (user) to the work:
Chery Kimo Read/Write EEPROM, Read/Write KM (Adapter J2534)
Chery Amulet Read/Write EEPROM, Read/Write KM(KLine)
Chery Tiggo ver 1 Read/Write EEPROM, Read/Write KM(KLine)
Chery Fora Read/..
$66.45
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.89
License 28, may be applicable at the discretion of the licensee (user) to the work:
Kia Sportage 2016 Yazaki Reading/KM record
Kia Sportage 2017+ Yazaki Reading/KM record
Kia NEC34+24c16 2015-...
Kia Optima Reading/KM Writing, Reading/EEprom Recording
Kia Ceed Read..
$79.74
License 15, may be applicable at the discretion of the licensee (user) to the work:
ECU on the NEC 34+24C16 microcontroller:
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording (program area + calibration)
..
$79.74
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
Supported ECU's MAGNETI MARELLI 7GV / 7GVE / 4HV
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
Soon will be added Simos 7.1/ 7PP/ 7.1 A
..
$79.74
Includes maps of the calibration firmware the Lada Largus and Renault Logan/Sandera (also the cards will be added calibrations from similar control systems, such as Kangoo, Symbol and others). Free map updates for new software EMS3132. Works with FullBIN 256 kb and the file of some calibrations (..
$66.45
Supported Mitsubishi:
MH8102F_(512K)
MH8201F_(512K)
MH8202F_(512K)
MH8301F_(512K) - 2001 Montero Sport 3.5 L ; from 2001 Pajero 3.0;
MH8302F_(512K) - from 2004 Galant 2.4 L MIVEC; 2003-2005 Outlander; Outlander 2.4 MIVEC CU5W AT 07/05 – 12/08; with 2003 Montero Spo..
$93.03
Module 'Module Bosch M78/ME797+ - OBD2' is designed to record via OBD2 connector firmware ECU Bosch M78, ME797+ cars Ukrainian and Chinese production. Currently supported ECU M78 cars ZAZ Forza, Geely CK2, Geely MK2, Geely Emgrand Great Wall Wingle, ECU M788 car JAC, Geely GC6, Chery Tiggo, Lifan..
$46.90
The module is designed to work with the engine control units (ECUs) produced by Continental for SGMW and Geely cars. For SIM2K-D51/51.4/SCE60, reading and writing through the diagnostic connector is supported, while for Easy U2/U2.5/U2W/U3.6, connection "on the bench" may be required. Checksum ve..
$93.03
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.61
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
The module is designed to read and write FLASH memory of ECU MT86 installed on a KIA/Hyundai. Working with these types of ECU's is via the J2534 device
ECU MT86 is a read only field calibrations. Recording is supported for the following formats:
Firmware reads th..
$42.41
Module 'China MT80 ECU - OBDII' is designed to read and write FLASH memory of ECU MT80 installed on Chinese vehicles through J2534 device and KLine adapter.
Supported the conversion and checksum. Recording is performed only in the area of calibrations.
For holders of CHIPSOFT J..
$93.09
Module GM SIM2K-243 - OBD2 is designed to read and write FLASH memory of ECU SIM2K-243 installed in the cars of GM via the J2534 device.
Supported the conversion and checksum field calibrations.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. ..
$68.54
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.73
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
Module GM MT60/MT80 Extended - OBD2 is designed to read and write full dump of the internal FLASH and EEPROM memory of ECU MT60/MT80 manufactured by GM. The module can be used to cloning units.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lit..
$84.82
Module EMS3120 (VAZ/Logan) - OBD2 is designed to read and write FLASH memory of ECU Siemens EMS3120 fitted to cars VAZ, Logan via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Speci..
$63.61
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
Module 'VW Polo ECU - OBDII' is designed to read and write FLASH memory of ECU Magnetti Marelli 7GV, 7GVE, 4HV, installed on the cars of VW via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% disco..
$88.17
The module is designed to read and write FLASH memory of ECU frame-mounted Mazda (2003-2013 year of release) via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 ( Lite) (Mid) adapter, a 50% discount on the module. Specify when o..
$93.09
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.45
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$26.58
Almost all types of blocks that are programmed via the Can bus are supported:
Matsushita SH7058 1024K
Matsushita SH72543 2048K
Continental MPC5554 2048K
Temic MPC5554 2048K
Keihin MPC5566 3072K
Keihin SH72543 2048K
Keihin SH7058 1024K
Hitachi SH70..
$159.47
Designed for chip-tuning of cars mounted ECU M12/M75/M74.5. Supported read and write via the diagnostic connector
..
$66.45
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$66.45
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.45
The module is designed to build, edit and compare an extended error mask according to the OBD/SAE standard for SUBARU car firmware with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). The module allows you not only to turn off, but to turn back the DTC error code.
..
$39.87
Toyota Camry cars with 2AR-FE engine, volume 2.5L
Supported software:
89663-06791-
89663-06794-
89663- 06A31-
89663-06A35-
89663-06A45-
89663-MODUM-
89663-33B51-
89663-33B52-
89663-33B60-
89663-33D71-
89663-33G81-
..
$39.87
Toyota Avensis cars with 2ZR-FAE gasoline engines, volume 1.8. Cost: 3000r.
Supported Software:
89663-01032-
89663-01121-
89663-02023-
89663-02161-
89663-02162-
89663-02172-
89663-02173-
89663-02182-
89663-02183-
89663-0..
$39.87
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.96
Module to work through the diagnostic connector for Ethernet control units Bosch MG1 and MD1 mounted on the BMW F and G-series.
Supported units Bosch processor-based NXP MPC5777 with 7.5 Mb of internal flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)
BMW Fx..
$419.53
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
The module is intended for cloning on the table, without parsing the ECU. Supported and filled in TCU in a metal case and not filled in a plastic housing.
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
..
$132.89
Module 'Denso SH7058 ECU - OBDII' is designed to read and write FLASH memory of ECU Denso SH7058 processor fitted to cars Suzuki, Mitsubishi, Volvo, and others circa 2007 - 2010 model years. Please note that only supports Denso ECUS in which the manufacturer laid the engineering way of working wi..
$113.19
Designed for chip-tuning of cars mounted ECU M12 / M75 / M74.5. Supported read and write via the diagnostic connector
..
$106.32
Designed for chip-tuning GAS with the installed ECU M12.3. Supported read and write FLASH via diagnostic connector
..
$66.45
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.73
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
The module is designed to work in service mode with the ECU of the ZF 8HP Gen 3, ZF 9HP, ZF 8DT (PDK2-TC400), MB 8G (VGS3-FDCT), VAZ AMT, Renault JHQ gearboxes using TC1782, TC275 and TC277 family microcontrollers. Read and write operations of the built-in FLASH and EEPROM memory are supported wh..
$199.34
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.89
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.89
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.60
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
$359.60
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.33
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.81
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
Module TC1762/TC1766/TC1796/TC1797/TC1767/TC1724/TC1738/TC1791/TC1793/TC1798/TC1728/TC1782/TC1784/GPT boot mode (ECU families Bosch ME17.9.x and other CPU Tricore TC1762 / TC1766 / TC1796 / TC1797 / TC1767 / TC1724 / TC1738 / TC1791 / TC1793 / TC1798 / TC1728 / TC1782 / TC1784)
Clo..
$180.15
The module allows you to view, compare and edit the firmware files of MAN c ECU EDC17CV42 cars.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error mask are available for editing. The modu..
$664.47
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.66
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
$299.66
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.73
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
The module is designed for recording and reading (read-only ECU Avtel M73) FLASH memory of the ECU family January-7.2+/M73 via diagnostic connector OBDII
At the moment not supported the ECU Avtel M73 with identifiers ending in DB04, and having such protection algorithms.
..
$11.71
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days.
MMC Flasher universal Downloader intended for chip tuning Hyundai, Kia, Mitsubishi, Mazda, Nissan, Honda, Subaru..
$30.57
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
License 132, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with the Continental VDO MQBAB dashboard based on the NEC35xx MK installed on cars: Audi,Skoda,Seat,VW, which allows for full-fledged repair and restoration work with ECU data.
..
$332.24
The Bosch EDC17C76 (DDE742) module is designed for chip tuning of BMW cars with N 57 x diesel engines. Installed on:
X5 Series F15
X6 Series F16
Pay attention:
A third-party developer module! Technical support from the author of the module (M. Glazyrin).
&nb..
$265.79
The Bosch MD1CP032 (DE 853) BMW module is designed for chip tuning of BMW cars with M47 and B57xx diesel engines.
Installed on:
X5 Series G05
X6 Series G06
X7 Series G07
Pay attention:
A third-party developer module! Technical support from t..
$332.24
The KMS MD1CE100 module allows you to view, compare and edit the firmware files of Kamaz K5 cars with an R6 engine (Bosch MD1CE100 ECU).
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, DPF, EGR, AdBlue, ..
$664.47
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.87
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
$119.87
Supports reading and writing of the Mazda c CPU SH7055 7058 and via J2534 interface ( only Tested with the Open port 2.0) by OBD2. Supported ECU Denso and Mitsubishi Corp. Latest restored from any state.
..
$79.74
Additional module for chip tuning BMW cars with Bosch MEVD17.2.5 control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load such firmware, on..
$132.89
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.73
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.80
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.61
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.74
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.74
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.61
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.58
Additional module for chip tuning BMW cars with Bosch MEVD17.2.8 and MEVD17.2.H control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load su..
$132.89
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
The module is designed for chip tuning of VAG cars (Skoda, Audi) with 1.0TFSI and 1.4TFSI engines equipped with Bosch MED17.1.27. Please note: Third-party developer module! Technical support from the module author (KHN09). Firmware for Bosch ME17 controllers is saved by default in SMS-Soft Contai..
$159.47
The Bosch EDC17CP45/CP 49 module (DE 731 P_730), (DDE731a P_731), (DDE731a P_731), (DDE751a P_1319) is designed for chip tuning of BMW cars with N47xx, N57xx, and B47xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, and F23
3rd series F3..
$332.24
The Bosch EDC17C50 (DE 701) BMW module is designed for chip tuning of BMW and MINI cars with N47x, B47xx and B37xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, F23, F45 and F46
3rd series E90, E91, F30, F31, and F34
4th series F32, ..
$332.24
The module is designed for chip tuning of VAG cars equipped with Bosch MED17.5.20 with 1.4 TFSI engines.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in..
$159.47
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.05
The module allows you to edit the firmware of SUBARU cars (2.0 engines) with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). Tables of UOZ, mixture composition, throttle position, torque request, error mask, etc. are available.
Supported Software:
E2UD00..
$39.87
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.73
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
The module supports: identification, read FULL flash, write field calibrations, the reading and deletion of errors, checking and correcting the checksum. Supported ECU's Continental SIM2K 140/141/241/341.
..
$79.74
The Bosch EDC17CP09 module (P_573 DDE73), (P_574 DDE73a), (P_613 DDE73) is designed for chip tuning of BMW cars with N57xx diesel engines. Installed on:
3rd series E90, E91, E92 and E93
5th Series F07
7th series F01 and F02
X5 E70 Series
X6 Series E71
Pay att..
$199.34
The module is designed for chip tuning of Citroen and Peugeot cars with 5GY (EP6FDTM), 5GZ (EP6FDT) engines equipped with Bosch MED17.4.4, for example, Peugeot 208 A9, Peugeot 308 T9, Peugeot 3008 T8, Citroen DS3 A55, Citroen DS5 B81, Citroen C4 Grand Picasso B78.
Pay attention:
..
$159.47
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.89
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.79
This module allows chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with the Abit M240 ECU.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the control program a..
$332.24
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
License 137 may be applicable at the discretion of the licensee (user) to work with:
TCM ECU automatic transmission 6L50 installed on UAZ Patriot vehicles.
Identification
Reading/Clearing the DTC
Reading/VIN entry
FLASH recording(calibration area)
T..
$132.89
Distribution of licenses after 08/31/2024!
License 145, may be applicable at the discretion of the licensee (user) to work with:
Simos 3x/7x/9x ECUs installed on VAG vehicles, which allows for full-fledged repair and restoration work with these ECUs.
Reading FULLFLASH
..
$106.32
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
Distribution of licenses after 06/14/2024
License 144, may be applicable at the discretion of the licensee (user) to work with:
ABS ECU on MK NXP Cortex M4 (FS32K144HFMLL) installed on Lada Racing, Lada Granta FL cars from 2024.
Identification
Reading/..
$159.47
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
License 136, may be applicable at the discretion of the licensee (user) to the work:
with direct connection via CAN bus with Magneti Marelli IAW 9 GVCE control units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data.
Magneti Marelli IAW 9GV..
$79.74
License 143, may be applicable at the discretion of the licensee (user) to the work:
with instrument panels on the MK Artery Cortex M4 (AT32F403) installed on Lada Granta and Lada Niva cars from 2024.
Identification
Reading/Clearing the DTC
Reading/KM Record
..
$79.74
License 135, may be applicable at the discretion of the licensee (user) to the work:
from CCBS to MK Artery AT32F435ZGT7(FlashSize: 1024KB) installed on Lada Vesta NG cars from 2022 or Lada Largus from 2024, which allows for full-fledged repair and restoration work with these types of ECUs.
..
$332.24
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.89
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.89
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.74
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.74
License 101 can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with multimedia units installed on GM cars, which allows for full-fledged repair and restoration work with ECU data.
Scope of application: Change of region, Us..
$332.24
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 27, may be applicable at the discretion of the licensee (user) to the work:
Hyundai/KIA MB91F061/062/067 WITHOUT EXTERNAL EEPROM
The work is carried out through the OBDII connector
Approximate operating time from 4 - 10 minutes
The list of cars is approxim..
$79.74
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
![[53] MERCEDES DELPHI CRD - OBD2](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[53] MERCEDES DELPHI CRD - OBD2")
