License 27, may be applicable at the discretion of the licensee (user) to the work:
Hyundai/KIA MB91F061/062/067 WITHOUT EXTERNAL EEPROM
The work is carried out through the OBDII connector
Approximate operating time from 4 - 10 minutes
The list of cars is approxim..
$79.74
ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong.
Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle.
Works through the J2534 interface.
ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato..
$93.03
License 35, may be applicable at the discretion of the licensee (user) to the work:
Hyundai Equus 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording, Reading/EEPROM recording
Hyundai Centennial 2013-2015 Full TFT LCD(Fujitsu MB91F037+93C66) Reading/KM Recording..
$79.74
The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector.
Table of applicability ECU SIMTEC 70:
Opel Astra G (1998-2000) X18XE1/X20XEV
Opel Vectra B (1998-2001) X18XE1/X20XEV
Opel Zafira (..
$119.61
The Nissan Denso Diesel 2.5 TDI SH7059 module is designed for chip tuning of Nissan Navara, Pathfinder, Cabstar, Murano, NV300, Caravan, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7059 processors.
Pay attention:
Third-party developer modules! Techni..
$132.89
New ECU M86 applies to cars UAZ Pro. Manufacturer software hardware — NPP ITELMA.
This module allows you to produce professional chip tuning UAZ Pro equipped ECU M86 with ITELMA. Edited more than 950 calibration management system M86, which allows full professional chip tuning UAZ...
$106.32
Distribution of activation files after 01.06.2023
License 118, may be applicable at the discretion of the licensee (user) to work:
with a Bosch electric power steering on the Nec V850 70F3187 + EEPROM 95080 MK on the table or via the OBDII connector (where there is a technical ..
$66.45
Cars equipped with ECU Mikas-11,ET(CR) and M73 with the latest version of the software. The module allows to work with the so-called 'closed ECU', which cannot work with standard modules Mikas-11/Mikas-11ET/Mikas-11CR/VS-8, January-7.2+/M73 or BSL.
..
$119.61
The module allows for chip tuning of GM cars (Chevrolet, Cadillac, etc.) equipped with an ACDelco E92 ECU, for example, Cadillac ATS 3.6L, Cadillac Escalade 6.2L, etc.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
..
$132.89
This module allows you to work on the car via the OBDII connector with the Visteon ECU installed on Ford cars.
Module Functions:
Identification Reading
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalculation of calibration area c..
$66.45
This module allows you to work on a car via an OBDII connector with Siemens ECM installed on Ford cars.
OBD II Mode (working on a car or on a desk):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalcula..
$66.45
License 88, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM(EMS3120/EMS3125/ValeoV40/42) during repair.
The work is done by upgrading the FullFlash file ..
$265.79
License 52, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Rec..
$132.89
The module allows you to perform chip tuning of Chevrolet cars equipped with an ACDelco E80 ECU.
Pay attention:
A third-party developer's module! Technical support from the author of the module (KHN09).
Working with firmware that does not contain the control program c..
$159.47
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.89
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.9 control units.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family controllers is saved in the SMS-Soft Containe..
$132.89
Hyundai and Kia: Carens, Cerato new, Magentis, Sonata, Sorento, new Sportage, ix35 and the other with an engine capacity of 2.0 and 2.4 L.
2.0L, 2.4L (SIM2K-140) [RD/WR/CK]
2.0L, 2.5L (SIM2K-D160) [RD/WR/CK]
2.0L, 2.4L (SIM2K-141/142/341) [RD/WR/CK]
2.0L (SIM2K-C201) [RD..
$93.03
The module is designed for chip tuning of VAG cars with gasoline engines 1.8TFSI and 2.0TFSI of the third generation: Audi A4/ A5 / A6, Audi Q3 / Q5, Audi TT, Porsche Macan, Skoda Octavia, Skoda Octavia RS, VW Passat, VW Polo GTI, VW Jetta, VW Tiguan, etc.
Note:
Third-party mod..
$239.21
The module is designed for chip tuning of Korean-made cars of 2018 and newer with GDI gasoline engines equipped with Kefico CPEGD2.20.1 / CPEGD2.20.2 / CPEGD2.20.3 / CPGDSH2.26.1 / CPGDSH2.26.3 / CPGPSH2.14 ECUs.1.
These ECUs are used on cars such as:
Hyundai Elantra, Avant..
$265.79
The module is designed for chip tuning of VAG concern cars with 2.0l diesel engines. Delphi DCM6 ECU.2.
The module contains more than 450 calibrations: speed limiter, engine torque limiters (incl. smoke) and transmission, torque model (calculation of the amount of injection, reques..
$265.79
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
Distribution of activation files after 11/30/2022
License 98, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode (Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading..
$106.32
Optional module for chip tuning of BMW cars with Bosch MEVD17.2.5
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Container File format..
$132.89
Optional module for chip tuning of BMW cars with Bosch MEVD17 control units.2.4
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09). The
firmware of the Bosch ME17 family of controllers is saved in the SMS-Soft Contain..
$132.89
The module is designed for chip tuning of BMW cars with the N55B30 engine.
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by d..
$132.89
The module is designed for chip tuning of Hyundai and Kia cars with EURO-6 diesel engines equipped with Denso ECU with SH72543/SH72546 processors.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported s..
$265.79
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
MDflasher software for odometer adjusting, to work with the immobilizer, the Airbag, and als..
$39.87
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.47
The Toyota Denso Diesel 4.5D (1VD-FTV) module with 76F0070 processor is designed for chip tuning of Toyota cars with 4.5L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported..
$239.21
The module is designed for chip tuning of Geely vehicles equipped with DSI TCM automatic transmission.
Module Features:
Limited module with a limited number of calibrations!
The module calculates the COP.
Hardware versions 02F and 02R are supported.
Suppor..
$93.03
The Toyota Denso Diesel 2.8D module supports all software versions, including GEN3; processors D76F0196F1 (1536Kb), D76F0219F1 (2048kB), R7F701202 (4096Kb). Designed for chip tuning of Toyota cars with 2.8L diesel engines, Denso ECU.
Pay attention:
Third-party developer mod..
$239.21
The module is designed for chip tuning of Hyundai Starex, Porter, HD78, i30, KIA Bongo and others cars with 2.5CRDI diesel engines, Delphi DCM 3.7 ECU.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
Supported software versions:..
$132.89
The module is designed for chip tuning of Audi A4, A5, VW Amarok, Crafter, Passat, Transporter cars with 2.0L TDI and 2.5L TDI diesel engines.
Allows for professional chip tuning of Bosch EDC17CP20 control systems. The possibility of correctly disabling the ecology of EGR, DPF, SCR (AdBlue).
..
$199.34
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The Toyota Denso Diesel 3.0D (1KDFTV) module with 76F0040GD, 76F0039AGD, 76F0070, 76F0085 processors is designed for chip tuning of Toyota cars with 3.0L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the modul..
$239.21
The module allows you to produce professional chip tuning of cars VAZ with electronic gas pedal (EGAS), equipped with the latest ECU M74. Also supports editing firmware ECM M74K (VAZ 'Classic', without an electronic gas pedal). Edited over 380 calibrations of the control system M74: starting mode..
$106.32
The module is designed for chip tuning of Suzuki Jimny, Liana, Grand Vitara, Swift, SX4 cars with 1.3L, 1.5L, 1.6L, 2.0L, 2.4L engines equipped with Denso ECU with SH7055 and SH7058 processors.
Pay attention:
A third-party developer module! Technical support from the author..
$79.74
The Toyota Denso Diesel 2.5 module is designed for chip tuning of Toyota cars with 2.5 diesel engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
Supported software versions, Toyota Denso Die..
$239.21
License 76, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording of the Flash memory of the ECU of the transmission of VAZ cars through the diagnostic connector or on the table (connection is available in the online help).
..
$66.45
License 51, may be applicable at the discretion of the licensee (user) to the work:
The module has two modes of operation - Auto search and calculator.
1. Auto-search mode:
Reading the mileage of VAG group cars by OBDII with the MED17/EDC17 ECU in meters.
..
$106.32
The Bosch EDC17C64 GAZ module is designed for chip tuning of GAZ group cars with VAG 2.0TDi diesel engines.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
The firmware of the Bosch EDC17 family controllers ..
$106.32
License 70, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Full Flash file, read in BSL mode or by a programmer.
Wor..
$106.32
The module is designed for chip tuning of Ssang Yong Actyon, Korando, Rexton, Rodius, Stavic, etc. cars with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulik..
$132.89
The module is designed for chip tuning of VAG cars with 1.8 TFSI and 2.0 TFSI petrol engines of the 3rd generation: Audi A4 1.8 TFSI, Audi A5 1.8 TFSI, Audi A5 2.0 TFSI, Audi A6 1.8 TFSI, Audi Q5 2.0 TFSI, Skoda Octavia 1.8 TFSI, Skoda SuperB
Pay attention:
A third-party de..
$239.21
The module is designed for chip tuning of Great Wall Hover cars and others with 2.0 TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported software versions:
&..
$106.32
The module is designed for chip-tuning diesel cars fitted with Continental SID807:
Citroen C3 1600 HDi
Citroen C3 Picasso 1600 HDi
Citroen C4 1600 HDi
Citroen C4 Grand Picasso 1600 HDi
Citroen C5 1600 HDi
Citroen DS3 HDi 1600
Citroen DS4 HDi 1600
..
$132.89
Additional module for chip tuning BMW cars with Bosch MEVD17.2.5 control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load such firmware, on..
$132.89
The module allows chip tuning of Opel, Chevrolet, Cadillac cars equipped with an ACDelco E37 ECU.
Examples of cars equipped with this type of ECU: Chevrolet Captiva (C140) 2011+, Opel Antara 2011+.
Pay attention:
A third-party developer module! Technical support from th..
$13.29
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
Bosch EDC17C64 module is designed for chip tuning of Audi A3 / A4 / A6 / Q5, VW Golf7 / Sharan / Tiguan, Skoda Octavia and others with 1.6L and 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
..
$132.89
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
Additional module for chip tuning BMW cars with Bosch MEVD17.2.8 and MEVD17.2.H control units. Please note: Third-party developer modules! Technical support from the module author (KHN09). Firmware for Bosch ME17 family controllers is saved by default in SMS-Soft Container File format. To load su..
$132.89
License 01, may be applicable at the discretion of the licensee (user) to the work:
Allows you to read and write the FULL Flash image 29F200/29F400.
Allows you to read/write the emulated in Flash EEPROM.
The "MAKE VIRGIN" function allows you to make the ECU "New", suitable ..
$132.89
The module is designed for chip-tuning diesel cars Ford, Peugeot and Citroen equipped with Continental SID208:
Ford Ranger 3.2 TDCI
Ford Transit 2.2 TDCI
Ford Transit 2.4 TDCI
Peugeot Boxer 2.2 HDI
Citroen Jumper 2.2 HDI
Please note:
Third-party modul..
$159.47
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.74
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
The module is designed for chip tuning of VAG cars (Skoda, Audi) with 1.0TFSI and 1.4TFSI engines equipped with Bosch MED17.1.27. Please note: Third-party developer module! Technical support from the module author (KHN09). Firmware for Bosch ME17 controllers is saved by default in SMS-Soft Contai..
$159.47
For chip-tuning of cars of Chinese production with electronic gas pedal.
..
$119.61
The module is designed for chip tuning of VAG cars equipped with Bosch MED17.5.20 with 1.4 TFSI engines.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in..
$159.47
The module is designed for chip tuning of Ford Focus 2.0, Maverick 3.0, Escape 2.3, Escape 3.0, Mazda Tribute 2.3 cars equipped with Visteon EEC-V ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (A. Teslya).
A Limite..
$106.32
The module is designed to work through the diagnostic connector of the car with transmission control units 6HP26, 5R/6R/6F/8F/10R of various modifications used in Ford cars. Supports reading, writing, checking and correcting checksums.
6HP26 TCM [RD/WR/CK]
5R110 TCM [RD/WR/CK]
..
$119.61
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
The modl is designed for chip-tuning Peugeot and Citroen cars with naturally aspirated petrol engines with electronic throttle, Bosch ME7.4.5 ECU.
Supported software versions:
08Sg0_D08Sg0
11Sb0_D11Sb0
13Sd0_D13Sd0
13Tb0_D13Tb0
18Ta0_D18Ta0
19T..
$106.32
The module is designed to work in service mode (on the table) with Bosch transmission control units with SH725xx family microcontrollers used in ZF 8HP, VAG DQ380/381/500, MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. It supports reading, writing, checking and correcting CS in FLASH memory and rea..
$132.89
License 32, may be applicable at the discretion of the licensee (user) to the work:
Chery Kimo Read/Write EEPROM, Read/Write KM (Adapter J2534)
Chery Amulet Read/Write EEPROM, Read/Write KM(KLine)
Chery Tiggo ver 1 Read/Write EEPROM, Read/Write KM(KLine)
Chery Fora Read/..
$66.45
Reading full image data
The writing of a complete image data
Identification
Recalculation of checksum
Work is required to remove the ECU.
Car Suzuki Carry DA16T 0.660L R06A 4WD 2014 Mitsubishi MH8115 33910-82M0 Bench 65
Car Suzuki Spacia ..
$132.89
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The module is designed to work through the diagnostic connector of a car with DSG and automatic transmission units used in VAG concern cars. It supports reading (virtual), writing, checking and correcting checksums.
DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL420/AL600 (09L/09E) K-Line..
$132.89
The Bosch MD1CS001 (DDE802L, DDE803S) BMW module is designed for chip tuning of BMW cars with B47D20xx diesel engines. Installed on:
3rd G20 Series
5th series G30 and G31
X3 Series G01
X4 Series G02
Pay attention:
A third-party developer module! Tech..
$332.24
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.73
License 115, may be applicable at the discretion of the licensee (user) to the work:
providing advanced functionality - working with instrument panels via the OBD II connector (where there is a technical possibility), installed on Hyundai/Kia cars since 2018, which allows for full-..
$79.74
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
$359.60
Toyota Denso Petrol 5.7i module for chip tuning of Toyota Sequoia, Tundra, Lexus LX570, etc. with 5.7-liter 3UR-FE and 3UR-FBE engines, Denso ECU.
Pay attention:
Third-party developer modules! Technical support from the authors of the module (V. Kulikova and A. Tesla).
..
$239.21
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.74
The module is designed for chip-tuning VAG cars with engines 1.8 T, 2.0 T, equipped with Bosch MED17.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Sof..
$159.47
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$93.03
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
The module is designed for chip tuning Hyundai Santa Fe, Hyundai Tucson, KIA Carnival, KIA Sorento Prime, KIA Sportage diesel engines 2.0 CRDi and 2.2 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmw..
$106.32
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Includes calibration cards for the firmware of the M86 ECU with VAZ software and the M74M ECU. As well as basic, non-calibrated dual-mode M86 (VAZ) and M74M firmware, dual-mode
firmware editing cards. The maps also contain additional calibrations of the "Extended Mix composition" for speciali..
$93.03
The car 'Lada Vesta/XRay/Largus' with electronic gas pedal, equipped with ECU M86/M74M.
The module is intended for read-write FLASH/EEPROM ECU М86 with a production of vases, based on the Infineon processor family XC27x5 via the built-in BootStrapLoader, and recording via the d..
$66.45
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
License 68, may be applicable at the discretion of the licensee (user) to the work:
1. Auto-search Mode:
Reading the mileage of HYUNDAI / KIA cars by OBDII with the MED17/EDC17 ECU.
Automatic search for the specified mileage in the EEPROM dump loaded into the program...
$106.32
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.32
New ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75/M74.5. Manufacturer of hardware — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the ..
$106.32
The Bosch EDC7UC31 MAZ / KRAZ / URAL module is designed for chip tuning of MAZ, KrAZ, MZKT, Ural cars and generator sets with diesel engines.
Supported firmware (software versions P766.120), module EDC7UC31 MAZ / KRAZ / URAL:
P766_120_MAZ_YAMZ-650_C_14_w_o_Cr_Ct
..
$265.79
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
License 40, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of the calibration area (with recalculation of checksums)
..
$106.32
The Bosch MD1CP002 (DE 832) BMW module is designed for chip tuning of BMW cars with B57D30xx and B47D20xx diesel engines.
Installed on:
3rd G20 Series
5th series G30 and G31
6th Series G32
7th series G11 and G12
8th series G14, G15 and G16
X3 S..
$332.24
License 80, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on Ford/Mazda cars,
which allows for full-fledged repair and restoration work with ECU d..
$79.74
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
The Ford EDC17CV41 module 24 allows you to view, compare and edit firmware files of Ford Cargo F-Max vehicles (Bosch EDC17CV41 ECU).
Calibrations are available for editing: boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phases, torque limits, ..
$398.68
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
License 109, may be applicable at the discretion of the licensee (user) to the work:
via the OBDII connector or on a table with 6RF(U)92086x instrument panels(white indication) based on the 70F3524 microcontroller without an external EEPROM installed on VAG Polo cars since 2014, wh..
$199.34
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.74
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
License 18, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM recording via OBDII.
Reading/FLASH recording via OBDII.
The module only works with panels on MK 9S12XHZ256.
List of supported cars:
Nissan Qashqai 2010+
..
$66.45
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.3 and MT22.5.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$119.61
The module allows to make the chip tuning of the car Geely Emgrand EC7, Geely Emgrand X7, Lifan X60, Lifan Cebrium, Solano Lifan, equipped with ECU Delphi MT22.1.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU p..
$119.61
Additional module for chip tuning Hyundai and Kia, ECU Continental (Siemens) SIM2K-241/242/245.
Supported versions:
KR77355119
KR77355121
KR77355122
KR77355137
KR77395114 (in development)
KR77395116
KR77395119
KR77315135
KR773..
$239.21
For chip-tuning of cars of Chinese production (Great Wall Hover, Great Wall Safe, BYD F3, Chery Tiggo, etc.).
..
$93.03
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$93.03
The module allows for chip tuning of Opel, Chevrolet, Cadillac cars equipped with ACDelco E39 and E39A ECUs.
Examples of cars equipped with this ECU type: Opel Insignia 2.0L A20NHH / A20NHT (LHU), Opel Antara 2011+ 3.0L (LF1), Opel Antara 2012+ 3.0L (LF1, LFW), Opel Astra-J A16XHT / 1.6L SIDI..
$132.89
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
The module is designed for chip tuning of VAG group cars with gasoline engines, Bosch MG1CS001 ECU, for example:
Audi A1 2.0 TFSI
Audi A3 2.0 TFSI
Audi A4 2.0 TFSI
Audi A5 2.0 TFSI
Audi A7 2.0 TFSI
Audi Q2 2.0 TFSI
Audi Q3 2.0 TFSI
Audi Q5 2.0 TFS..
$186.05
Cars Renault Duster 1.6 L and 2.0 L.
..
$66.45
The module is designed to edit the data of the registrar of the VAZ 74.8 and M74.9 blocks with NPO Itelma. The module monitors the integrity of the data when opening and recalculates all the necessary CS when saving. An EEPROM (4 kilobytes) is used for editing.
..
$26.58
The module is designed for chip-tuning VAG cars equipped with Magneti Marelli 7GV, for example, the VW Polo 1.6 L, VW Jetta 1.6 L, Skoda Rapid 1.6 L, Skoda Fabia 1.6 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$132.89
The module allows you to produce professional chip tuning of motorcycles (CF-Moto X6 EFI, etc.) ECU Bosch MSE3.0.
The programming of this ECU is carried out using a Bosch module M(E)7.9.7 (OBDII) loader CombiLoader.
Deep research (reverse engineering) of the program ..
$132.89
The Nissan Denso Diesel 2.5 TDI SH7058 module is designed for chip tuning of Nissan Cabstar, Condor, Navara, NP300, Pathfinder, Vanette, X-Trail, etc. cars with 2.5TDI diesel engines equipped with Denso ECU with SH7058 processors.
Pay attention:
Third-party developer module..
$132.89
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
Module DQ500 is designed for chip-tuning VAG cars (7 speed DSG, which is installed on the cars of concern VAG c a transverse engine).
Please note:
Modules a third-party developer! Technical support from the author of the module (V. Kulikova).
Modules are independent f..
$199.34
The module is designed for chip tuning of Chevrolet Captiva, Cruze, Orlando, Daewoo Winstorm, Opel Antara, etc. with 2.0TDI and 2.2TDI diesel engines, Delphi DCM 3.7 ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kuli..
$132.89
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.89
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.32
License 85, may be applicable at the discretion of the licensee (user) to the work:
Correction of mileage readings with recalculation of checksums in the read EEPROM area of the processor firmware,
in DSG DQ200, DSG DQ200_MQB, DSG DQ200 G2, DSG DQ250 E/F(02E) units installed on..
$79.74
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.45
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.89
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$66.45
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$33.22
Cars 'Lada Granta' with electronic gas pedal, equipped with ECU M74 and M74CAN.
..
$33.22
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
License 99, may be applicable at the discretion of the licensee (user) to the work:
1. OBDII Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculation of checksums)
..
$106.32
The module allows you to read FLASH and write software /calibrations of the Bosch M SE 6.0 ECU installed on various models of motorcycles.
..
$106.32
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The 88 Ford AdBlue module is designed to work with the AdBlue DCU17PC43 dosage ECU, installed on Ford cars paired with the SID212/SID212EVO engine ECU, via a diagnostic connector. Supports reading, writing, checking and correcting checksums.
AdBlue REDCM (DCU17PC43) [KV6A] [RD/WR/CK]
..
$66.45
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.87
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
The cars of Chinese production (Great Wall Hover, BYD, etc.) with Delphi MT20U ECU, MT20U2, MT20UED, MT22U and MT22.1. Supported read and write FLASH and EEPROM.
..
$93.03
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
The Bosch EDC17CP09 module (P_573 DDE73), (P_574 DDE73a), (P_613 DDE73) is designed for chip tuning of BMW cars with N57xx diesel engines. Installed on:
3rd series E90, E91, E92 and E93
5th Series F07
7th series F01 and F02
X5 E70 Series
X6 Series E71
Pay att..
$199.34
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
1.5L dCi Delphi DCM 1.2 (ST10/512KB) [RD/WR/CK]
1.5L dCi Delphi DCM 3.4 (SH7059/1536KB) [RD/WR/CK]
1.5L dCi SID 301/303/304 (MPC562/2MB) [RD/WR/CK]
1.5L dCi SID 305/306 (TC1766/1504KB) [RD/WR/CK]
1.5L dCi SID 307 (TC1767/2MB) [RD/WR/CK]
2.3L dCi SID 309 (TC1767/2..
$93.03
Designed for chip tuning of ECU Abit M20.20, M20.21, M240, M240S1, MD22. Modules allow you to: - Read and write calibration area - Read and write control program - Calculate and, if necessary, automatically correct the checksum of the calibration area - Perform ECU identification - Read and reset..
$132.89
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
The module is designed for chip tuning of Citroen and Peugeot cars with 5GY (EP6FDTM), 5GZ (EP6FDT) engines equipped with Bosch MED17.4.4, for example, Peugeot 208 A9, Peugeot 308 T9, Peugeot 3008 T8, Citroen DS3 A55, Citroen DS5 B81, Citroen C4 Grand Picasso B78.
Pay attention:
..
$159.47
License 108, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS Siemens W3, Siemens VW51, Siemens VW52 units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data:
..
$66.45
Module kit:
The module is designed to read/write FLASH memory of DSI TCM ECUs installed on SsangYong/Geely vehicles via the diagnostic connector. The module performs automatic correction of the COP of calibrations during recording.
The module is designed to write software / calibrat..
$93.03
Cars Renault Logan 2, Sandero 2, Fluence, Megane 3, Latitude, Duster.. Designed to read and record the calibration and program the ECU mounted on Renault cars via diagnostic connector.
..
$66.45
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.79
The module is designed for reading and writing software and calibrations of the Delphi DCM 6.2V ECU of VAG group cars via UDP protocol via the diagnostic connector.
The module automatically corrects CS calibrations during recording.
The module supports the "Virtual r..
$132.89
This module allows chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with the Abit M240 ECU.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the control program a..
$332.24
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.73
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.34
The module is designed for chip-tuning VAG cars equipped with Bosch ME17.5.26, for example, Skoda Octavia 1.6 MPI, Skoda Rapid 1.6 MPI Skoda Yeti 1.6, 1.6 MPI VW Jetta, VW Polo 1.6.
Please note:
Third-party module developer! Technical support from the author of the module (..
$159.47
This module allows you to perform chip tuning of bi-fuel cars equipped with the Abit A12.2 ECU. The ECU is programmed using the CombiLoader loader.
When saving the firmware, the checksums are automatically recalculated.
Research with the help of reverse engineering of the contr..
$132.89
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Cars equipped with ECU М124 (new version ECU Mikas, for installation on automobiles GAZ.).
..
$53.16
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.68
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.32
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$66.45
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
License 22, may be applicable at the discretion of the licensee (user) to the work:
MB91F016A R/W WORK FLASH, R/W MAIN FLASH
MB91F060BS R/W WORK FLASH, R/W MAIN FLASH
MB91F061BS R/W WORK FLASH, R/W MAIN FLASH
MB91F062BS R/W WORK FLASH, R/W MAIN FLASH
MB91F067BS R/W..
$106.32
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.32
License 29, may be applicable at the discretion of the licensee (user) to the work:
Recording the mileage of dashboards on EEPROM 95040 cars before 2011
Recording the mileage of dashboards on EEPROM 95160 cars after 2011
Universal module, works with a large numbe..
$79.74
The module is designed to work with the Mitsubishi ECU of cars of various brands on the "table". Supports read, write, review, and correction checksums:
CAN-bus Bootloader FLASH (MH8114F/MH8115F/MH8501F) [RD/WR/CK]
CAN-bus Bootloader FLASH (MH8601F/MH8610F/MH8611F/1N83M) [RD/WR/CK]
..
$119.61
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
BitBox is an evolving software package that allows to identify, read and write the internal ..
$46.96
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.89
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
License 37, may be applicable at the discretion of the licensee (user) to the work:
PIN reading
Reading ID keys
Reading the number of keys
List of supported ECUs:
BOSCH 17.9.11(Hyundai/Kia)
BOSCH 17.9.12(Hyundai/Kia)
..
$79.74
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5, for example, VW Tiguan 2.0 L TSI, VW Passat B6 1.8 L, Skoda Oktavia 1.8 L TSI, Audi A4 1.8 L TFSI, Seat Altea, Skoda Yeti 1.8 L TSI, etc..
Please note:
Third-party module developer! Technical suppo..
$159.47
License 131 may be applicable at the discretion of the licensee (user) for work with: - MC series TriCore AUDO TC17xx installed in the ECUs of various manufacturers' engines.
Reading PFLASH
Writing PFLASH (except OTP areas)
Reading DFLASH
Writing DFLASH
Calculation..
$159.47
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
The Bosch EDC7UC31 KAMAZ module is designed for chip tuning of KAMAZ vehicles with diesel engines of the KAMAZ-740 family.
Supported firmware (software versions P702.141, P986.310), EDC7UC31 KAMAZ module:
702V141_740.60-360-290812_5460-4010142-01
702V141_740.60-360-29..
$265.79
The module is designed for chip-tuning of cars of the VAG group (Audi A3/A4/A5/A6/Q3/Q5/TT, Skoda Superb, VW Golf, VW Passat, VW Tiguan, etc.) with a diesel engine capacity of 2.0 L, EDC17C46 Bosch ECU.
Please note:
Third-party module developer! Technical support from the a..
$132.89
The module is designed for chip tuning of BRP leisure equipment:
ATV/UTV Can-Am 4-stroke engines of 600/800/900/1000/1300 cc (atmospheric and turbocharged)
Commander
Maverik
Maverick X3
Maverick X DS
Spider
Sea-Doo jet skis with 4-stroke engine..
$132.89
The Bosch EDC7UC31 GAZ module is designed for chip tuning of GAZ and MAZ cars with YAMZ-5344.20, YAMZ-53416, YAMZ-53441.20, YAMZ-53442, YAMZ-536, YAMZ-53601, YAMZ-53602, YAMZ-53603, YAMZ-53613, YAMZ-53622, YAMZ-53623, YAMZ-53624, MMZ-245 diesel engines.7.
Supported firmware (softwa..
$265.79
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.74
License 82, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars Nissan / Infiniti, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 08, may be applicable at the discretion of the licensee (user) to the work:
The work is done by upgrading the Flash file.
Works as an editor.
DENSO engine control units on NEC 76F00xx processors with firmware size are supported 256, 320, 368, 384, 496, 736, 992, 1024.
..
$79.74
License 24, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$106.32
License 26, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash or EEPROM file, depending on the type of ECU.
Works as an edit..
$106.32
The module is designed to work through the diagnostic connector of a car with Delphi DCM6.2 engine control units used in VAG concern cars. Virtual reading, writing, checking and correction of checksums are supported.
1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/RD/WR/CK]
..
$132.89
License 11, may be applicable at the discretion of the licensee (user) to the work:
Renault MeganIII/Scenic III/Fluence/ClioIII/Modus
Restores the eeprom Eur dump (EPS), makes it "new" - ready for installation on the car.
Identification of the ECU.
Read..
$106.32
License 138, may be applicable at the discretion of the licensee (user) to work with:
ECU EGS gasoline engines installed on UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(full content)
FLASH recording (control program + calibration area or ..
$66.45
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
$179.80
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.89
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
License 15, may be applicable at the discretion of the licensee (user) to the work:
ECU on the NEC 34+24C16 microcontroller:
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording (program area + calibration)
..
$79.74
Cars VAZ. Used 2008
..
$66.45
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
VW Touran, Golf, Passat, Transporter, Caddy cars with engines AVQ,BKC,BMT,BLS, etc. with a volume of 1.9L
Supported Software:
1037367485P379U6FP
1037368205P213U6FT
1037370254P213U8C3
1037370811379U85B6
1037371094379U85B6
1037371250379U85B6
..
$39.87
Toyota Corolla cars with 1ZR-FE, 3ZZ-FE 1.6 petrol engines
Supported software:
89663-02240-A
89663-02241-
89663-02270-A
89663-02482-
89663-02483-
89663-02491-
89663-02492-
89663-02502-
89663-02503-
..
$39.87
The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles.
Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors.
..
$132.89
Toyota Camry cars with 2AR-FE engine, volume 2.5L
Supported software:
89663-06791-
89663-06794-
89663- 06A31-
89663-06A35-
89663-06A45-
89663-MODUM-
89663-33B51-
89663-33B52-
89663-33B60-
89663-33D71-
89663-33G81-
..
$39.87
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to v..
$51.83
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
The module is designed to build, edit and compare an extended error mask according to the OBD/SAE standard for SUBARU car firmware with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). The module allows you not only to turn off, but to turn back the DTC error code.
..
$39.87
Toyota Camry, Rav4, Avensis cars with gasoline engines 1AZ-FE, 3ZR FAE, 3ZR-BE, 3ZR-FE, volume 2.0
Supported software:
89663-05A11-
89663-06460-
89663- 06B40-
89663-06E10-
89663-42053-
89663-42192-
89663-42590-
89663-42600- Ah
..
$39.87
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
Toyota Avensis cars with 2ZR-FAE gasoline engines, volume 1.8. Cost: 3000r.
Supported Software:
89663-01032-
89663-01121-
89663-02023-
89663-02161-
89663-02162-
89663-02172-
89663-02173-
89663-02182-
89663-02183-
89663-0..
$39.87
The Valeo V4X module is designed to read and write the FLASH memory of the Valeo S3000/V40/V42 ECU installed on Renault cars through the diagnostic connector.
The Sagem S3K module is designed to read and write calibrations and the program of the Sagem S3000 ECU (512k FLASH) install..
$66.45
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
Pay attention:
Third-party developer modules! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in SMS-Soft Container File format by default. To download such firmware, you need to use only the CombiLoader loader.
Savi..
$106.32
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
The module is designed to create dual-mode firmware with an individual set of calibrations for the second mode. When you create a dual-mode firmware of the usual standard you can select the calibration, which will create steam in the second set, getting an individual set of calibrations needed fo..
$53.16
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.74
New cars VAZ with electronic gas pedal.
..
$106.32
Toyota Land Cruiser 150 cars with 1GD-REV diesel engine Cost: 3000r.
Supported Software:
89663 - 60X23
89663 – 60X24
89663 – 60X26
89663 – 60X27
89663 – 60X28
89663 – 60X29
89663 – 60Z31
89663 – F0594
89663 – F0595
89663 – F0599
..
$39.87
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
Module MM4HV designed for chip-tuning VAG cars equipped with Magneti Marelli 4HV, for example, VW Polo 1.4 L, VW Jetta 1.4 L, 1.4 L Skoda Rapid, Skoda Fabia 1.4 L.
Please note:
Modules a third-party developer! Technical support from the author of the module (KHN09).
Read and wri..
$132.89
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$119.61
License 75, may be applicable at the discretion of the licensee (user) to the work:
Reading/FullFlash Entry
Reading/EEPROM recording
The ability not to overwrite the boot sector.
The module allows you to use your Seed Key, in case it was replaced with a non-s..
$106.32
License 30, may be applicable at the discretion of the licensee (user) to the work:
INFINEON XC2361 Reading/Write FLASH, Read Flash, Clear collision information.
INFINEON XC2336 Reading/Write FLASH, Read Flash, Clear collision information.
MAC7242 Reading/EEPROM recording, Cle..
$79.74
Module DL501 designed for chip-tuning VAG cars (Audi and other vehicles VAG with longitudinal engine).
Please note:
Modules a third-party developer! Technical support from the author of the module (V. Kulikova).
Modules are independent from each other and are ..
$132.89
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The basic version of the program ChipLoader with support for the following types of ECUS:
January-5.x, January-7.2, VS-5.1, Bosch M7.9.7, M7.9.7+, Mikas-7.1, Mikas-7.6, Mikas-10.3..
$86.36
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
$239.73
Module DQ250 is designed for chip-tuning VAG cars equipped with automatic transmissions DSG6 DQ250 Rev. C/E/F(02E), MQB(0D9).
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Supported versions of DQ250 ON:
..
$132.89
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
Module allow to make the chip tuning Hyundai Genesis/Equus, Kia Cadenza/Quoris/Sorento Prime engines 3.3/3.8/5.0 l, equipped with ECU Delphi MT86.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delph..
$132.89
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.73
For chip-tuning of cars of Chinese production (Great Wall Hover, Great Wall Safe, BYD F3, Chery Tiggo, etc.).
..
$93.03
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
License 137 may be applicable at the discretion of the licensee (user) to work with:
TCM ECU automatic transmission 6L50 installed on UAZ Patriot vehicles.
Identification
Reading/Clearing the DTC
Reading/VIN entry
FLASH recording(calibration area)
T..
$132.89
The module allows converting the serial software M74.9 Niva, Granta, Vesta, Largus, Gazelle into a dual-mode version. It can be used for professional installation of LPG systems. It only works with a license for the M74.9 VAZ and/or M74.9 GAZ modules as follows: Having a M74.9 VAZ license allows ..
$79.74
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.32
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
$179.80
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
Toyota Denso Petrol 5.0i module for chip tuning of Toyota Century G60 (2017 - present), Lexus IS-F XE20 (2007 — 2014), Lexus RC-F XC10 (2014 — present), Lexus GS-F L10 (2015 — present), Lexus LC 500 URZ100 (2016 — present), Lexus LS 600h XF40 (2007 — 2017), etc. models with 5.0-liter 2UR-GSE and ..
$239.21
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.73
Toyota Denso Diesel 2.0D module for chip-tuning Toyota cars (Auris, Avensis, Corolla, Verso) with diesel engines 2.0L 1CD-FTV / 1AD-FTV, Denso ECU, 76F0004 320kB, 76F0040 368kB, 76F0039 496kB, 6F0038 736kB processors, 76F0085 992kB.
Pay attention:
Third-party develope..
$239.21
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.96
Bosch EDC17C74 module is designed for chip tuning of Audi A3 / Q2, VW Golf / Passat / Tiguan, Skoda Superb / Kodiaq and others with 2.0L TDI diesel engines.
Note:
Third party module! Technical support from the author of the module (V. Kulikov).
By default, the firmwar..
$132.89
Designed for chip tuning of VAZ cars with M74.8 ECU
..
$106.32
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
The program ChipExplorer is a powerful file editor firmware of the ECU with the following features:
Review the values of calibration in the form of 2-and 3-dimensional graphs.
Adva..
$236.59
For chip-tuning Opel cars with engines Z16XER and Z18XER.
..
$132.89
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
$359.60
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
For chip-tuning cars Mitsubishi Lancer 10 (except vehicles with engines of 1.5 L).
..
$79.74
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.45
Allows you to edit and compare the error mask on a large number (about 1000) of Denso software. The module allows you not only to turn off, but to turn back the DTC error code.
Supported Software:
89663-01032- 89663-01121- 89663-02023- 89663-02161- 89663-02162- 89663..
$39.87
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
$299.66
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$26.58
For chip-tuning of cars Tagaz Tager/Road Partner and Ssang Yong Musso, Actyon, Rexton, Kyron petrol engines 2.3/2.8/3.2 L.
..
$93.03
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
The module is designed to work with DCM6.2AP, DCM7.1AP ECUs installed on Chinese-made cars via a diagnostic connector. Supports reading, writing, checking and correcting checksums.
Changan 2.0L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng 2.3L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng/Yucha..
$132.89
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
$359.60
For chip-tuning cars Mitsubishi Lancer 10 with engines of 1.5 L.
..
$79.74
Attention! This module works in conjunction with CombiLoader 2.16 or later.
The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector.
The module automatically corrects CS calibrati..
$66.45
Diagnostic cord for diagnostics of cars BMW F-Series. The device connects to the network card of the PC or laptop and doesn't need any special adapters. To work with the scanner PC must be installed specialized software BMW ISTA/D Rheingold E-SYS. Software not included.
Functionality:
..
$20.38
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days.
MMC Flasher universal Downloader intended for chip tuning Hyundai, Kia, Mitsubishi, Mazda, Nissan, Honda, Subaru..
$30.57
License 112, may be applicable at the discretion of the licensee (user) to the work:
when directly connected via CAN/K-Line bus (depends on the selected type of ECU) with Delphi control units installed on cars of various Chinese manufacturers, which allows you to perform full-fledged chip tun..
$132.89
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.73
Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor.
Available the following cards:
Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure ..
$239.73
The module allows you to produce a professional chip tuning Lada Largus cars equipped with ECU Continental EMS3120.
Supported firmware versions:
HW7908R_SW09350_90047
Features of the module:
The possibility of open firmware (FullFlash only) in BIN format or SMS-Soft Cont..
$106.32
The module is designed for chip tuning Citroen/Peugeot with engines 1.2/1.6 L, equipped with ECU Valeo V46.
Supported firmware for hardware version V46.21.
The module works in conjunction with ChipTuningPRO 7.2016 or higher. The ECU programming is done using the loader CombiLoader.
Th..
$66.45
The Bosch EDC17C76 (DDE742) module is designed for chip tuning of BMW cars with N 57 x diesel engines. Installed on:
X5 Series F15
X6 Series F16
Pay attention:
A third-party developer module! Technical support from the author of the module (M. Glazyrin).
&nb..
$265.79
The module is designed to work with EMS S6 units installed in trucks Scania, approximately, 2006-present. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of ca..
$66.45
Designed for chip-tuning of cars VAZ with established ECU M74/M74CAN. Supported read and write FLASH/EEPROM memory controller via BSL mode
..
$66.45
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
The Bosch MD1CP032 (DE 853) BMW module is designed for chip tuning of BMW cars with M47 and B57xx diesel engines.
Installed on:
X5 Series G05
X6 Series G06
X7 Series G07
Pay attention:
A third-party developer module! Technical support from t..
$332.24
The Bosch EDC17CP45/CP 49 module (DE 731 P_730), (DDE731a P_731), (DDE731a P_731), (DDE751a P_1319) is designed for chip tuning of BMW cars with N47xx, N57xx, and B47xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, and F23
3rd series F3..
$332.24
License 06, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
Skoda Fabia 2011 (P/N 5J0920810E) Reading/KM Recording, Reading/Write EEPROM, Read Pin
Skoda Octavia A5 2009 (P/N 1Z0920803B) Reading/KM Recording, Reading/Write EEP..
$106.32
Designed for chip-tuning of cars VAZ, GAZ, UAZ, ZAZ installed the ECU Я7.2+, M11/М11ЕТ/М11CR/M73/M10.3/M11.4/ Bosch M7.9.7 and M7.9.7+
..
$66.45
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
The Bosch EDC17C50 (DE 701) BMW module is designed for chip tuning of BMW and MINI cars with N47x, B47xx and B37xx diesel engines.
Installed on:
1st series F20 and F21
2nd series F22, F23, F45 and F46
3rd series E90, E91, F30, F31, and F34
4th series F32, ..
$332.24
The China EDC17CV44 Truck module allows you to view, compare and edit firmware files of FAV cars, Shacman trucks, MAZ, Yutong, etc. with a WP7, KR10, WP12 engine with an EDC17CV44 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection pha..
$332.24
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.88
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.66
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
License 135, may be applicable at the discretion of the licensee (user) to the work:
from CCBS to MK Artery AT32F435ZGT7(FlashSize: 1024KB) installed on Lada Vesta NG cars from 2022 or Lada Largus from 2024, which allows for full-fledged repair and restoration work with these types of ECUs.
..
$332.24
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
For chip-tuning of cars Lifan.
..
$53.16
License 143, may be applicable at the discretion of the licensee (user) to the work:
with instrument panels on the MK Artery Cortex M4 (AT32F403) installed on Lada Granta and Lada Niva cars from 2024.
Identification
Reading/Clearing the DTC
Reading/KM Record
..
$79.74
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the abi..
$79.74
Module 'Module Bosch M78/ME797+ - OBD2' is designed to record via OBD2 connector firmware ECU Bosch M78, ME797+ cars Ukrainian and Chinese production. Currently supported ECU M78 cars ZAZ Forza, Geely CK2, Geely MK2, Geely Emgrand Great Wall Wingle, ECU M788 car JAC, Geely GC6, Chery Tiggo, Lifan..
$46.90
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$66.45
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.89
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
License 101 can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with multimedia units installed on GM cars, which allows for full-fledged repair and restoration work with ECU data.
Scope of application: Change of region, Us..
$332.24
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
$239.73
License 113, may be applicable at the discretion of the licensee (user) to the work:
For reading in BSL mode (parsed on the bench) and writing indiscriminately on the bench or on the car.
The following ECU types are supported:
Bosch M7.9.7 K-Line
A block base..
$132.89
Additional module for chip tuning Nissan X-Trail 2.5 L, ECU Bosch ME7.9.20.
The module works in conjunction with ChipTuningPRO 7.2018 or later. The ECU is equipped with an external (calibrated) and internal (management program) of the flash memory. Reading and writing to external m..
$106.32
License 136, may be applicable at the discretion of the licensee (user) to the work:
with direct connection via CAN bus with Magneti Marelli IAW 9 GVCE control units installed on VAG cars, which allows for full-fledged repair and restoration work with ECU data.
Magneti Marelli IAW 9GV..
$79.74
The module allows you to view, compare and edit the firmware files of MAN c ECU EDC17CV42 cars.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error mask are available for editing. The modu..
$664.47
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.89
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.89
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.74
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.74
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
Working with this type of ECU is 'on the bench'.
Car Volvo S60 Y283 I5T_13A200_257_Y283_2.5L_US_AWD 31411200AA 2010 Denso SH72543 31312651AB Bench 69
Car Volvo XC60 Y413 Y413_A_MP_150hp_Eu6b 31669250AB 150 2010 Denso SH72546 31452623 Bench 69
Car Volvo V40 Y555 Y555_M_LP_150hp_Eu6b ..
$132.89
The module is intended for read / write FLASH and EEPROM ECU MIKAS-12, M74.5, M75 and M86 running programs production ELKAR/ITELMA installed on new cars UAZ and VAZ with electronic gas pedal.
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new for..
$106.32
Distribution of licenses after 06/14/2024
License 144, may be applicable at the discretion of the licensee (user) to work with:
ABS ECU on MK NXP Cortex M4 (FS32K144HFMLL) installed on Lada Racing, Lada Granta FL cars from 2024.
Identification
Reading/..
$159.47
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.87
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
License 03, may be applicable at the discretion of the licensee (user) to the work:
Chevrolet Cruze, Opel Actra J, Insignia and their platforms:
BCM
Identification
- Reading KM
- KM record
- PIN reading
- Disassembly of the block (Reset PIN)
-..
$505.00
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
The module is designed for Chip tuning ECU SID211 installed on the following models Ford Transit, Ranger, Tourneo Connect diesel 2.0 L Ecoblue engine.
List of cars:
Car Ford PANTHER 2.0 105/130PS S/S GK21-14C204-AAA Continental TC1791 OBD 88
Car Ford PANTHER 2.0 105/130PS ..
$93.03
License 04, may be applicable at the discretion of the licensee (user) to the work of:
Suzuki Swift Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Kizashi Continental VDO Reading/EEPROM Writing, Reading/KM record.
Suzuki Grand Continental VDO Reading/EEPROM ..
$66.45
License 12, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$79.74
Allows you to work with Renault Clio/Megane/Scenic/Logan, equipped with systems Sirius32/EMS3132/Sirius34/EMS3134. ECU programming directly on the vehicle through the diagnostic connector. The main difference from similar applications is the ability to read/write programs for a replacement.
I..
$66.45
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
$239.73
License 05, may be applicable at the discretion of the licensee (user) to the work:
Autoliv production units
INFINEON XC2361 Reading/EEPROM recording, Flash reading, Clearing collision information via CAN.
INFINEON XC2336B Reading/EEPROM recording, Flash reading, Clea..
$79.74
License 78, may be applicable at the discretion of the licensee (user) to the work:
With various ECUs in BSL mode on the table, on the Infineon XC2xxx, C167, ST10 microcontroller families, they can be found in various ECUs powered by cars of various concerns. Sample list of ECUs:
..
$79.74
License 41, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the ACDelco E83 ECU in OBD II Mode, Bench Mode and Recovery mode.
1. OBDII Mode(Car operation):
Reading Identification
Reading Er..
$106.32
License 33, may be applicable at the discretion of the licensee (user) to the work:
VW Polo (P/N 6RF920860Q) Reading/KM record
Not all software versions may be supported.
..
$79.74
The KMS MD1CE100 module allows you to view, compare and edit the firmware files of Kamaz K5 cars with an R6 engine (Bosch MD1CE100 ECU).
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, DPF, EGR, AdBlue, ..
$664.47
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Toyota Denso Diesel 2.4 D module for chip tuning of Toyota (Hilux) cars with 2.4 L 2GD-FTV diesel engines, Denso ECU, processors D76F0196F1 1.5 MB, D76F0219F1 2MB.
Pay attention:
Third-party developer modules! Technical support from the author of the module (V. Kulikova).
..
$239.21
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.33
License 63, may be applicable at the discretion of the licensee (user) to the work:
Works with panels:
NEC + 24C64 06/2010+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64 06/2012+ Reading/KM Recording, Reading/Write EEPROM, Read Pin
NEC + 24C64..
$199.34
License 62, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
$239.73
License 50, may be applicable at the discretion of the licensee (user) to the work:
Reading/KM record
Reading/FLASH recording(program and calibration area)
FLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
License 42, may be applicable at the discretion of the licensee (user) to the work:
Dacia Logan RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Lada Largus FL RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, E..
$79.74
License 89, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by Delphi.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading/EEPROM Wri..
$106.32
License 34, may be applicable at the discretion of the licensee (user) to the work:
Renault Megane III Reading/KM Recording ,Reading/EEPROM recording in the ABS/CDC/ESP blocks of the ATE manufacturer
Renault Laguna III Reading/KM Recording ,Reading/EEPROM recording in the ABS/C..
$159.47
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.74
License 45, may be applicable at the discretion of the licensee (user) to the work
Reading/KM record
Reading/FLASH recording (program and calibration area)
DFLASH reading
Reading/Record configuration
Not all software versions may be supported.
..
$79.74
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
License 20, may be applicable at the discretion of the licensee (user) to the work:
Mitsubishi ASX 2014+ 8100B951 (NEC 70F3529 without external EEPROM) Read/write KM, read/write eeprom
Mitsubishi ASX 2014+ 8100B961 (NEC 70F3523 without external EEPROM) Read/write KM, read/write..
$79.74
License 23, may be applicable at the discretion of the licensee (user) to the work:
Mazda 6, CX5, CX7 2013+ Read, Write KM/ Read, Write EEPROM.
Mazda 2.3 2014+ Read, Write KM/Read, Write EEPROM.
Mazda MX5 2015+ Read, Write KM/Read, Write EEPROM.
Mazda 3 2010-2013 Read, W..
$79.74
The module allows you to edit the firmware of SUBARU cars (2.0 engines) with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). Tables of UOZ, mixture composition, throttle position, torque request, error mask, etc. are available.
Supported Software:
E2UD00..
$39.87
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
License 38, may be applicable at the discretion of the licensee (user) to the work:
Mazda 3 Color Display (93c86) 2018-... Reading/KM record
Mazda 6 Color Display (93c86) 2016-... Reading/KM record
Mazda 6 Color Display (93c86) 2017-... Reading/KM record
Mazda CX5 Color ..
$79.74
License 17, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording EEPROM 24c04 or 93c56 (depends on the type of panel) by OBDII or direct connection on the table (connection in the help).
Correction of odometer readings by OBDII or direct connecti..
$66.45
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
$239.73
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.5, for example, VW Touran 1.4 TFSI, VW Golf IV 1.4 TSI, VW Tiguan 1.4 TSI, Skoda Superb 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.2, for example, VW Passat 1.8 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the f..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.21, for example, the VW Golf 1.4 TSI, Skoda Octavia 1.2 TSI, Audi A3 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch М..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.25, for example, the VW Golf 1.2 TSI, 1.4 TFSI, Skoda Octavia, Skoda Superb 1.4 TFSI, VW Jetta 1.4 TFSI.
Please note:
Third-party module developer! Technical support from the author of the module (K..
$159.47
License 10, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the EEPROM file.
Works as an editor.
List of supported ECUs:
..
$132.89
License 19, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording KM by OBDII.
Reading/Recording HERPROM by OBDII.
Reading FLASH by OBDII.
Nissan/Infiniti cars from 2011 and above with the Continental VDO NEC 34+24C16 dashboard are sup..
$79.74
FID: 337
A module for reading and writing Shindengen control units installed on Honda motorcycles.
Honda Moto Shindengen V850/RH850 K-Line (FID:337)
Sihndengen engine control units are powered by Renesas V850/RH 850 series processors with 256/384Kb internal flash memo..
$247.15
The module is designed for chip-tuning, car Hyundai I40, Hyundai IX35, KIA Soul diesel engines 1.6 CRDi and 1.7 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Firmware families Bosch МEDC17 are stored by..
$106.32
License 60, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
&..
$132.89
License 58, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by CONTINENTAL.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 95..
$106.32
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.32
License 44, may be applicable at the discretion of the licensee (user) to the work:
Read/Write FLASH processors SH7058,SH7059,R4F70580, R4F70590 (without recalculation of checksums).
Read/Write Opel EEPROM
Read/Write Mitsubishi EEPROM
Read/Write Suzuki EEPROM
Readi..
$106.32
License 36, may be applicable at the discretion of the licensee (user) to the work:
Audi A3 Mk3 07.2014+ Reading/KM record
Audi Q2 Reading/KM record
Skoda Fabia III 07.2014+ Reading/KM record
Skoda Octavia III 07.2014+ Reading/KM record
Scoda Rapid 09.2015+ Reading..
$332.24
License 02, may be applicable at the discretion of the licensee (user) to the work:
Continental SID 305 Reading/KM record
Continental SID 306 Reading/KM record
Continental SID 307 Reading/KM record
Continental SID 309 Reading/KM record
Delphi DCM3.4 Reading/KM reco..
$106.32
License 13, may be applicable at the discretion of the licensee (user) to the work:
Reading/Clearing fault codes
Clearing collision information.
Unlocking the ECU.
Changing the ECU configuration.
Reading/VIN entry.
List of supported ECUs:
Renault SAND..
$79.74
License 21, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
List of supported ECUs:
..
$106.32
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.73
The module is designed for Chip tuning TCM (TCU) module automatic transmission has the internal name of the Power Stroke and mounted on the following models Ford F450, F350, F250, Explorer, Edge, Territory, and other
List of cars:
Car Ford MY11 E265 ASSY PART AR79-14C337-AC 201..
$93.03
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
$239.73
License 55, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
R7F701002 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701003 READ,WRITE CFLASH//DFLASH//UBOOT//OPBT0
R7F701006 READ,WRITE ..
$79.74
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 20 minutes).
BitEdit is a modern editing of calibrations the car, allowing to change the basic parameter..
$46.96
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.73
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$39.87
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$106.32
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
Cars equipped with ECU M114 (new version ECU M10.3, is mounted on Daewoo Sens, GAZelle, etc.).
..
$46.51
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.73
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.81
License 53, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to read and write a full memory image (FULL FLASH) for cloning the ECU.
List of supported ECUs:
Simtec 71.5
Simtec 71.6
Simtec 75.1
Si..
$106.32
The cars of Chinese production Lifan, Breeze, etc. is Designed to read / write FLASH and EEPROM ECU Siemens Vagon VAx
..
$53.16
RoadPartner cars TagAz/TaGeR/SsangYoung Rexton with engines 2.3/2.8/3.2 L. Intended for read-write FLASH memory via the diagnostic connector.
..
$66.45
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.22
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E78.
Examples of vehicles equipped with this type of ECU: Opel Astra J A14NET, A14NET Opel Opel Corsa C, Opel Mocca A14NET, A14NET Chevrolet Cruze, Chevrolet Tracker A18XER, Chevrolet Malibu A..
$132.89
The car is equipped with ECU January-7.2+, M73, M74K. Does not work with 'closed' versions of the ECU M73!
..
$33.22
The family of modules includes three separate module from the ECU to the M74.5, M75, MIKAS-12 or M86 (FOR ITELMA, firmware, VAZ and UAZ), which can be purchased independently. All the modules have identical functionality and are designed to create dual-mode firmware with an individual set of cali..
$53.16
The module is designed for chip-tuning VAG group diesel engine 3.0 L ECU Bosch EDC17CP44.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are stored by default in the format of SMS-Soft..
$132.89
Includes all the module 1, the calibrated dual-mode under LPG firmware M73 (all the existing software) and maps editing dual-mode firmware. So, buyers free program DoubleM73 tied to the key.
..
$59.80
The module is designed for chip tuning Hyundai(I30, I40, IX35, Santa Fe) and Kia(CEE'd, Optima, Soul, Sportage, Venga) with diesel engines 1.6 CRDi, 2.0 CRDi.
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Fir..
$106.32
The BMW cars with ECU Siemens MS41/42/43: E36/E38/E39/E46/E53 6-cyl 2.0 L — 3.0 L. ECU Programming can be performed directly on the vehicle through the diagnostic connector.
..
$66.45
Toyota Camry, Highlander, and Lexus cars with 2GR-FE 3.5l gasoline engines
Supported BY:
89663-06772- 89663-06G70- 89663-06P00- 89663-0E050-A 89663-0E340- 89663-22290-A 89663-30A11- 89663-33340-A 89663-33341- 89663-33640-A 89663-33641- 89663-33642- 89663-33650-A 8966..
$39.87
Additional module for chip tuning Peugeot with the control units Bosch MEVD17.4.2.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Containe..
$132.89
The module is designed for chip-tuning VAG group (VW Amarok, VW Crafter, VW LT) with a diesel engine capacity of 2.0 L, ECU Bosch EDC17C54.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC..
$132.89
The module is designed for chip-tuning VAG group (VW Tiguan, Touareg) with a diesel engine capacity of 3.0 L, Bosch ECU EDC17CP14.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МEDC17 are st..
$132.89
The module is designed for chip-tuning of automobiles in China, equipped with Bosch ME17.8.8, for example, Chery Tiggo 2.0 L, Chery Bonus (A19), Lifan X60, Lifan Solano II, etc.
Please note:
Third-party module developer! Technical support from the author of the module (KHN0..
$132.89
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
$359.60
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.66
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.89
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.89
The module is designed for chip-tuning of automobiles in China, equipped with Bosch MED17.8.10, for example, Geely Atlas 1.8 T.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored ..
$159.47
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.34
Toyota Camry, Rav4 cars with 2.4L 2AZ-FE petrol engines
Supported versions:
89663-02802-
89663-02822-
89663-06431-
89663-33021-
89663-33041-
89663-33691-
89663-33701-
89663-33702-
89663-33720-A
89663-33721-
..
$39.87
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$492.48
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
$239.73
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.89
Designed for chip-tuning of cars VAZ, UAZ with mounted ECU BOSCH ME17.9.7. Supports only FLASH programming through the diagnostic connector
..
$106.32
Designed for chip-tuning of cars and cars of Chinese production installed ECU BOSCH M7.8. Supports recording FLASH via the diagnostic connector. As well as reading and writing FLASH/EEPROM memory controller via BSL mode.
..
$66.45
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
$239.73
License 43, may be applicable at the discretion of the licensee (user) to the work:
Renault Kadjar Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Megane I V Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Espace..
$79.74
The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices.
The modules support the following types of ECUS:
MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB.
MagnetiMarelli MM7GV:..
$66.45
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$66.45
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$132.89
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.45
Designed for chip tuning of MAZ cars with installed WISE15 ECU (WEICHAI). To work with the WISE15 ECU, you need a 24V J2534 adapter and a CAN2CAN adapter.
..
$132.89
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
The module is designed to work with automatic transmission control units installed on cars developed in China.
Changan Alsvin 5DCT (EAST80.51/SPC563M) [VR/WR/CK]
Changan Alsvin 5DCT Bootloader (EAST80.51/SPC563M) [RD/CK]
Chery CVT19 (EAST80.11/MPC5534) [VR/WR/..
$132.89
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.73
The module is designed to work with Bosch ECU installed in the Honda cars. Supported ECU MED17.9.3, EDC17C58 (write after unlocking in BSL) as well as EDC17CP06, EDC17CP16 (recording without unlocking).
PGM-FI (Bosch EDC17CP06/EDC17CP16/2MB) [WR/CK]
PGM-FI (Bosch EDC17CP50/4MB) [Unl..
$93.03
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$26.58
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$79.74
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
Designed for chip-tuning of cars VAZ with established ECU M86 (FOR vases and * ITELMA).
..
$66.45
Distribution of licenses after 08/31/2024!
License 145, may be applicable at the discretion of the licensee (user) to work with:
Simos 3x/7x/9x ECUs installed on VAG vehicles, which allows for full-fledged repair and restoration work with these ECUs.
Reading FULLFLASH
..
$106.32
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
The module is designed for reading and writing ECU MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90, installed on BMW cars.
Work with the ECU is performed on the table without opening the ECU. Identification and error reading/reset functions..
$199.34
Module allow to make the chip tuning Hyundai/Kia with engines V6 2.7/3.3/3.8 L, equipped with ECU Delphi MT38.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
ECU programming Delphi MT38 by means of the loader CombiL..
$132.89
The module is designed to work with the ECU Kefico/Denso processor SH72546 installed in cars with a diesel engine of 2.5 l, standards of toxicity Euro-6. Supported read, write, review, and correction checksums.
Kia/Hyundai 2.5L CRDI (SH72546) [RD/WR/CK]
Hyundai Euro 5 (Denso SH7058S..
$93.03
The kit contains modules:
Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L.
Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particu..
$66.45
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$119.61
The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles.
Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available.
..
$199.34
The module is designed to work with a DC4 transmission control UNIT, installed in the cars of Renault. Supported read, write, review, and correction of the COP.
EDC DC4 Gearbox (TC1766/1506KB) [RD/WR/CK]
EDC DC0/DC4 Gen2 (DKG250 Gen2) (TC1784/2560KB) [RD/WR]
..
$66.45
Module GM SIM2K-243 - OBD2 is designed to read and write FLASH memory of ECU SIM2K-243 installed in the cars of GM via the J2534 device.
Supported the conversion and checksum field calibrations.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. ..
$68.54
The module is designed to work with the ECU from diesel engines 1.6, 2.0, 3.0 and 4.2 TDI are installed on passenger cars and crossover vehicles group VAG, approximately 2010. Supported entry, verification and correction of the COP.
2.0L, 3.0L TDI (EDC17CP04/EDC17CP14/EDC17CP..
$119.61
The module is designed for reading and writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture). The module is designed for reading and writing FLASH and EEPROM of ECU M74.8+ with ITELMA software, based on STMicroelectr..
$66.45
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
$299.66
The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$132.89
The module is designed to work with the Bosch ECU automatic transmission 6HP, 8HP a / m JLR through the diagnostic connector of cars. Supported read, write, check checksum correction:
ZF 6HP26/6HP28 TCM (MPC5xx/TC1766) [RD/WR/CK]
ZF 6HP28 Continental TCM (TC1766) [AH42-Ax] [R..
$119.61
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
Cars Renault Logan/Sandero Stepway/Megane/Fluence with engines of 1.2 L and 1.6 L.
..
$66.45
Includes maps of the calibration firmware the Lada Largus and Renault Logan/Sandera (also the cards will be added calibrations from similar control systems, such as Kangoo, Symbol and others). Free map updates for new software EMS3132. Works with FullBIN 256 kb and the file of some calibrations (..
$66.45
For owners module M75
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To ..
$46.51
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
$299.66
The modules are designed to read / write flash memory of ECU Visteon ESU-131/312/411/412/415/418 vehicle Ford Focus 2, C-Max, Kuga engines 1.8...2.0 l (2004...2010) and Ford Mondeo 4 S-Max, Galaxy with 2.0 engine...2.3 l (2004..2011 onwards)
..
$106.32
Module is designed to work with the ECU of 2.0L Delphi DCM6.2A/DCM6.2C diesel engines installed on PSA group cars, working through a diagnostic connector. Supports reading, writing, checking and correcting checksums:
Citroen/Peugeot 2.0L HDi (DCM6.2A) [RD/WR/CK]
Citroen/Peugeot 2.0L..
$93.03
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
$239.73
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
Kia, Hyundai, equipped with ECU Siemens SIMK43 and SIMK41, Chery QQ cars equipped with ECU Siemens SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface)
..
$53.16
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Panasonic processor Infineon Tricore TC197X with internal flash memory 4Mb.
..
$239.73
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
The module is designed for chip tuning of Peugeot, Citroen, Opel, Toyota cars with 2.0l diesel engines (PSA EMP2 platform). Delphi DCM6.2 / 6.2A / 6.2C ECU.
The module contains more than 400 calibrations: speed limiter, torque and power limiters (more than 60 limiters in total, inc..
$265.79
Set of 5 modules 1,2,3,4,5 Toyota Denso Diesel. Allows you to edit all available diesel cars are Toyota, Lexus, Hino on the units of DENSO. 10% savings when ordering.
..
$1 402.43
The module allows you to write firmware diagnostic method, without removing the ECU from the vehicle through the DLC (to work with the ECU on the car must be connected directly to the connector of the UNIT to disassemble the unit is not required).
Support ECU Bosch MSE3.0, M7.9.7, ME7.9.7, M7..
$66.45
This module allows you to make chip-tuning of cars GAZ and UAZ vehicles that equipped with ECU Mikas-11, Mikas-11CR, Mikas-11ET, VS-8.
Supports the following versions:
The number of the ECU and firmware version of the ECU
824.3763.001-05 0789_101
821.3763.000-01 0..
$66.45
New car equipped with an engine 21127 with adjustable geometry intake tract.
..
$106.32
Supports reading and writing c petrol Mazda Sky Active engines of 2.0 and 2.5, which require the ECU manufactured by Denso.
Car Mazda 6 GJ 2.5L Skyactiv-G PY3GEE000PY0B060 192 DENSO SH72543 PY3G-188K2-E OBD 33
Car Mazda 6 GJ 2.5L Skyactiv-G PY3HEG000PY0B060 192 DENSO SH72543 PY3H-18..
$66.45
Set of 8 modules 1,2,3,4,5,6 Petrol Toyota Denso, Toyota Denso Toyota Denso OLD and Petrol Turbo. Allows you to edit all available petrol cars are Toyota, Lexus, Scion on the units of DENSO. 10% savings when ordering.
10% savings when ordering.
..
$2 049.70
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
$179.80
The module allows you to convert any serial in three-mode version. Support switching complete sets of calibrations, including identifiers and the mask of DTC. Toggle options: channel or DTV channel ДК2. Provided disabling the fuel pump (with programmable delay) and the injectors individually for ..
$79.74
Toyota Denso Diesel 2.2 D module for chip tuning of Toyota/Lexus cars (Verso, Avensis, RAV4, Auris, IS220) with 2.2 L 2AD-FHV / 2AD-FTV diesel engines, Denso ECU, processors 76F0039 496kB, 6F0038 736kB, 76F0085 992kB.
Pay attention:
Third-party developer modules! Technical ..
$239.21
Module DQ200 is designed for chip-tuning VAG cars equipped with automatic transmission DQ200 DSG6 Rev. DQ200 (0AM), DQ200MQB (0CW), DQ200G2 (0CW).
Please note:
Third-party module developer! Technical support from the author of the module (V. Kulikova).
Supported versi..
$132.89
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
$239.73
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
Kit modules:
Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector.
Isuzu Transtron ..
$106.32
This module allows you to make chip-tuning BMW MS42 ECU (engine MT52TU, Serie 3 E36, 5 E39 Serie) and MS43 (E46 Serie 3, Serie 5 E39, X5 E53). The module works in conjunction with ChipTuningPRO 7 or higher. The ECU programming is done using the loader CombiLoader.
Maps contain more than 150 c..
$93.03
Update ChipExplorer 2 from Standard to Professional
..
$58.61
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Powerful, convenient and easy to use graphical editor calibrations in combinati..
$39.87
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
The module is designed to work with the ECU EDC7/EDC16/EDC17 diesel engines Mitsubishi Fuso Canter. Supported read, write, review, and correction of the COP. For some cars with ECU EDC7/EDC16 for writing may require a direct connection to the connector block.
Fuso Canter (EDC7C4-6/EDC16C3..
$132.89
FIDs: 142, 143, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 349, 353
A module for working with gasoline, electric and diesel cars with Denso SH72xxx CAN control units.
The work is performed when connected to the table via the CAN bus. Removing the ECU is necessa..
$239.73
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
$167.81
For chip-tuning of automobiles in China, equipped with ECU Bosch M7.9.7 and M7.9.7+.
..
$66.45
Support cars: Hyundai Accent, Elantra, Kia Rio, Cerato, Ceed
..
$52.71
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
$299.05
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.53
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb.
..
$79.74
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb..
$79.74
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$66.45
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$39.87
For chip-tuning cars Opel turbocharged a series of engine Z20LEL, Z20LEH, Z20LER.
..
$93.03
For chip-tuning of cars Chery (QQ, Fora, B11, Acteco, Elara, Jagga, Eastar).
..
$66.45
For chip tuning cars Chevrolet Captiva and Opel Antara with the engine volume of 3.2 L.
..
$93.03
Support cars: Chevrolet Lacetti, Tacuma Ukrainian production
..
$46.90
Set of 6 modules Honda Keihin + Matsushita + Hitachi + Continental + Motorola and Bosch Petrol Turbo. Allows you to edit almost all of the available petrol Honda cars for all markets. 10% savings when ordering.
..
$3 236.37
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.61
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
The USB key works only in the Basic loader Combiloader. No usb host and adapter PACK v3 key will not work!
The security key used for securing the operation of the loader with new modules. The design of the key allows the user to update the firmware (firmware) of the internal processor.
..
$39.87
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports the read/write and the conversion stock firmware with base IDS (VBF) in binary form.
..
$66.45
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.8 ECU. More than 900 calibrations of the M74.8 control system are available for editing, allowing virtually unl..
$159.47
The module allows for professional chip tuning of cars "Niva Legend 21214" and "Niva Travel 2123" of the 2022 model year with an electronic gas pedal (EGAS) equipped with the latest M74.9 ECU. More than 900 calibrations of the M74.9 control system are available for editing, allowing virtually unl..
$159.47
Module features:
Reading calibrations
Recording calibrations
Reading the full data image
Recording a complete data image
Identification
Reading/erasing errors
Recalculation of the checksum
The module also supports:
..
$66.45
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
$239.73
The module is designed for Chip tuning Mazda 2019 model year, are equipped with ECU Denso by Frima {PYFB} Mitsubishi {PYFA} and engines 1.5 L, 2.0 L, 2.5 L, 2.5 T
List of cars:
Car Mazda CX-3 DK 2019 Denso OBD 78
Car Mazda CX-5 KF 2019 Mitsubishi OBD 78
..
$93.03
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71.
Available the following cards:
The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficien..
$239.73
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.73
The module supports:
A quick read full dump of the processor (7058 -5 min; 7055 -2,5 min)
Slow reading, that would add ECU indiscriminately (from 50min)
The full dump of the processor (7055 -15 min; 7058 -25 min)
Recalculation of checksum
Recovery recording session..
$119.61
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.18
Universal adapter to work:
panel DENSO
UART
at MBUS
The Board has the following pin:
DTR
DTS
TX
RX
IGN
GND
12V
3.3 V
5V
MBUS
Designed to work with the modules of the software complex MDFLASHER
..
$126.25
For chip-tuning Opel cars with engines Z10XEP, Z12XEP, Z14XEP.
..
$93.03
Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb.
Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture,..
$239.73
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
$599.33
For chip tuning Hyundai vehicles equipped with KEFICO ECU or Bosch 7.9.7.
..
$66.45
For chip-tuning Ford Focus II with engines 1.4—1.6 L without adjustable phase timing, ECU Siemens SIM28.
..
$106.32
Includes the following modules:
module SRS AIRBAG Renault Continental Temic Motorola OBD2
Allows clearing CRASH DATA in blocks on the processors 9s12XDT384+95640 .
These units were installed in the cars of Renault Fluence /Megane III / Latitude / ScenicIII / KangooII / TwingoII
..
$79.74
The module allows for chip tuning cars Daewoo Gentra, equipped with ECU Delphi MT60.
..
$66.45
The module is intended for recording and(or) region calibration ECU Siemens EMS2204, installable in particular on cars Ford Focus 3 engine 1.6 l
..
$66.45
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
$119.87
Module features:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Recalculation of the checksum
Supports reading Full Flash and recording calibrations, Subaru gasoline cars, ECU manufactured by Hitachi/Unisia Jecs with ..
$119.61
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
$132.89
License 79, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Takata SRS units based on SPC560P34L1 processors installed on Lada Vesta and UAZ Patriot cars, which allows for full-fledged repair and restoration wor..
$66.45
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, th..
$239.73
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
The module allows you to view, edit, compare the firmware files of Kamaz, JAC, Foton cars with a Cummins 3.8L engine with a Continental CM2220 control unit. It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader. The module contains more than 1000..
$398.68
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
$359.60
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.61
For chip-tuning Chevrolet Captiva cars with engines 2.4 L.
..
$106.32
License 132, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with the Continental VDO MQBAB dashboard based on the NEC35xx MK installed on cars: Audi,Skoda,Seat,VW, which allows for full-fledged repair and restoration work with ECU data.
..
$332.24
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any e..
$86.38
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.60
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
The module allows you to produce professional chip tuning Lada X-Ray and Renault Duster/Kaptur, equipped with ECU Continental EMS3125.
Supports any version of calibration based on series RDE450, RDE540, RDE570.
Features of the module:
About 550 of calibration..
$106.32
The module allows you to produce a professional chip tuning for Renault Logan, Renault Sandero, Nissan Almera engine 1.6 L, automatic transmission, equipped with ECU Continental/Siemens EMS3134.
Supported versions:
REA820
REA830
Features of the module:
The possibil..
$79.74
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
Updated version of programmer XPROG-M v5.55 is intended for programming of new microcontroller and memory chip manufacturers, Motorola, Infineon, Micronas, Texas, Atmel, ST, National(CR16), M35080 and immobilizer EWS-3, CAS4 5M48H including software is protected from reading.
Authorization th..
$97.89
Includes maps calibrations for all versions (free map updates for new software). Works with standard (uncompressed) format. Writing a modified firmware available only via BSL mode any existing boot loader.
..
$93.03
The module allows you to produce a professional chip tuning for Renault Logan and Renault Sandero 2 2 that equipped with ECU Continental EMS3120.
Supported IDs firmware module Logan/Sandero:
HW4319R_SW4234R_4541R
HW4319R_SW4234R_4928R
HW4319R_SW4234R_4929R
HW4319R_SW..
$106.32
The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector.
Is free app for all users 2 or 3 version of module BSL TC17xx J2534.
Module Bosch MEDC17 Hyundai/Kia supported the following types of EC..
$106.32
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2A.
..
$359.60
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
The module allows you to produce professional chip tuning Mitsubishi Outlander XL with engines of 2.4 L and 3.0 L (manual and CVT) and Mitsubishi ASX with dvigatelem 2.0 L and Citroen C-Crosser and Peugeot 4007 made on the platform of the Outlander. Has no analogues on the number of calibrations ..
$79.74
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.53
License 39, may be applicable at the discretion of the licensee (user) to the work:
Subaru Outback 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Subaru Legacy 2015+ Reading/Write NEC D70F35xx EEPROM, Read/KM record
Not all software versions may be supporte..
$79.74
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
License 90, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
License 77, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (..
$106.32
A set of 7 modules to edit all available petrol cars Nissan and infiniti with the control units from Hitachi. 15% savings when ordering the kit.
The list of modules includes:
Nissan Hitachi Petrol Gen1 SH7054
Nissan Petrol Gen1 Hitachi SH7055
Nissan Hitachi Petrol Gen1 SH7..
$1 630.17
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
License 9, may be applicable at the discretion of the licensee (user) to the work:
Toyota NEC VDO+24C16 Corolla/Avensis/Auris 2013+ Reading/KM recording; Reading/EEPROM Entry 24C16
Toyota NEC VDO+24C16 2014+ AVENSIS / AURIS COROLLA Reading/KM recording; Reading/EEPROM Entry 24C16
..
$79.74
License 16, may be applicable at the discretion of the licensee (user) to the work:
ECU on the MB96F386+95160 microcontroller
Starting the ECU on the table
Reading/KM record
Reading/EEPROM recording
Reading/Flash recording(program area + calibration)
..
$79.74
Module 'Denso SH7058 ECU - OBDII' is designed to read and write FLASH memory of ECU Denso SH7058 processor fitted to cars Suzuki, Mitsubishi, Volvo, and others circa 2007 - 2010 model years. Please note that only supports Denso ECUS in which the manufacturer laid the engineering way of working wi..
$113.19
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
What is this system?
If You have several branches or regular customers that You make the firmware and they are interested in our product – they can get all the modules that You have, but they will not have access to the firmware, and You will keep the secret of your development. Th..
$299.66
The module is designed to work with the engine control units (ECUs) produced by Continental for SGMW and Geely cars. For SIM2K-D51/51.4/SCE60, reading and writing through the diagnostic connector is supported, while for Easy U2/U2.5/U2W/U3.6, connection "on the bench" may be required. Checksum ve..
$93.03
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$199.34
Sending activation files after 02/22/2022!
The module works with BCM manufactured by Bosch, Continental Gen.1(2 byte SeedKey), Gen.2(5 byte SeedKey).
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Readin..
$106.32
License 74, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.80
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
License 49, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
..
$132.89
License 46, may be applicable at the discretion of the licensee (user) to the work:
Skoda Octavia A7 03.2014 Reading/KM record
Audi A3 2012...06/2014 Reading/KM record
Seat Leon 2012...06/2014 Reading/KM record
VW Golf 7 2012...06/2014 Reading/KM record
W..
$332.24
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.89
License 31, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
It only works with the full firmware version (FULL FLASH..
$106.32
License 28, may be applicable at the discretion of the licensee (user) to the work:
Kia Sportage 2016 Yazaki Reading/KM record
Kia Sportage 2017+ Yazaki Reading/KM record
Kia NEC34+24c16 2015-...
Kia Optima Reading/KM Writing, Reading/EEprom Recording
Kia Ceed Read..
$79.74
The module is intended for editing data from Ieprom blocks Bosch ABS9, VAZ cars (XRAY / VESTA). You can change the main mileage, mileage after ECU reset, TPMS log mileage, VIN, Hardware ID, wheel diameter, TPMS activation flag. The module monitors the integrity of the data upon opening and recalc..
$26.58
Designed for chip-tuning of cars mounted ECU M12/M75/M74.5. Supported read and write via the diagnostic connector
..
$66.45
Designed for chip-tuning of cars mounted ECU M12 / M75 / M74.5. Supported read and write via the diagnostic connector
..
$106.32
Designed for chip-tuning of cars Hyundai, KIA, CHERY, GEELY, HAFEI, VORTEX ESTINA c installed ECU BOSCH M7.9.7,M7.9.7+,МЕ7.9.7, M(G)7.9.8
..
$66.45
The module is designed to work with the CRD3/CD3 ECU installed in Mercedes Benz cars. Work is supported through the diagnostic connector and "on the table". Supports reading, writing, checking and correcting checksums. It is possible to clone the ECU.
Mercedes-Benz CRD3/CRD3P FLASH [RD/WR..
$93.03
Module for the calibration firmware different motorcycles BRP, Ducati, Arctic Cat, Stels, Dinli, etc. with the control units Continental M3C.
Available the following cards:
The calculated mass air flow to throttle position, correction of the estimated air flow correction volume..
$299.66
Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
$143.84
License 59, may be applicable at the discretion of the licensee (user) to the work:
The module works with the following types of processors:
D70F3230 -D70F3231 -D70F3232 -D70F3233 -D70F3234 -D70F3235 -D70F3236 -D70F3237 -D70F3238 -D70F3239 -D70F3333 -D70F3334-D70F333..
$66.45
Module EMS3120 (VAZ/Logan) - OBD2 is designed to read and write FLASH memory of ECU Siemens EMS3120 fitted to cars VAZ, Logan via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Speci..
$63.61
The unit Valeo V40/V42 - OBDII is designed to read and write FLASH memory of ECU Valeo V40/V42 Renault cars.
The module must J2534 device.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% discount on the module. Specify when ordering the serial number of your adapter and appl..
$45.25
Module Bosch ME17.9.7(1)-OBD2 with write support ECU Bosch ME17.9.7 via the OBD2 socket of the car VAZ, UAZ, as well as records with ECU Bosch ME17.9.71 UAZ.
Please note that for correct record ECU Bosch M(E)17.9.71 you must first disable the monitoring of a digital signature, and writing the..
$58.61
Module Delphi MT20U/MT38/MT20U2/MT22U-OBDII (cars Chery, BYD, Hoover, Lifan, Kia, Hyundai)
..
$70.27
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.61
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.80
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
$299.66
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.73
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
$239.73
ORANGE-5 is a modern programmer for working with microcontrollers and memory chips. The feature of this series of devices is the built-in HPL macro language, which allows easy addition of support for new types of chips in full compliance with manufacturers' recommendations. This approach ensures ..
$198.24
Module 'VW Polo ECU - OBDII' is designed to read and write FLASH memory of ECU Magnetti Marelli 7GV, 7GVE, 4HV, installed on the cars of VW via the J2534 device.
Supported the conversion and checksum.
For holders of CHIPSOFT J2534 (Lite, Mid, Pro) adapter, a 50% disco..
$88.17
Psupport cars: Daewoo Nexia, Lanos, Nubira, Leganza
..
$46.90
Psupport cars: Chevrolet Aveo, Lacetti Ukrainian production
..
$46.90
Supports reading and writing of the gasoline auto. Mazda with volumes 2.0, 2.5, 2.3 T - CX7,3,6 2010+
..
$93.03
FID: 340
Module for working with Honda/Acura cars via CAN bus with Keihin control units.
The family supports control units:
Keihin SH7058 (1MB)
Keihin SH72543 (2MB)
Keihin MPC5554 (2MB)
Keihin TC1782 (2.5MB)
Keihin TC275 (4MB)
Ke..
$308.93
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
$239.73
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
$239.73
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 8..
$66.45
For owners module M74 6.38
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works ..
$46.51
Supports reading and writing diesel Mazda with SH7058 processor in QFP-256 (none BGA) and software on the basis of RF7x
..
$39.87
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.45
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
FIDs: 346, 347
A module for working on a CAN bus with control units of Peugeot and Citroen petrol cars.
PSA Valeo V46.11 (FID: 346)
The control unit is powered by a Renesas SH72544 processor with 2.5 Mb internal flash memory. Allows reading and writing of the..
$179.18
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.81
Basic kit:
GM ISFI-2S
VAZ, the first serial electronic control system on domestic cars.
January 4
VAZ, second serial electronic system of injection control, the domestic counterpart of ISFI-2S. Used since 1995
January-5.1.x
VAZ, a domestic ..
$66.45
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
$299.66
A set of their 5 modules discount for Toyota cars.
The kit includes:
Denso Toyota Gen1 CAN
Toyota Denso Gen2/newGen CAN
Toyota Denso Gen3 CAN
Toyota Delphi Gen1 CAN
Toyota Gen1 Virtual Reader
..
$1 018.86
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.66
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
$239.73
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
$119.87
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
The cars ECU:
Logan / Sandero EMS3120 TC1738 [2048k] CAN
Fluence / Megane EMS3120 TC1738 [2048k] CAN
Fl..
$86.38
Supports reading Full Flash and recording of calibrations petrol cars Suzuki, ECU manufactured by Hitachi c CPU SH7058. Recalculation of the CRC. Read & clear error ECU internal combustion engine.
Suzuki Escudo 2.7 L Suzuki Grand Vitara 2.7 L
..
$66.45
The Bosch module M(E)7.9.7-OBDII (Bosch Kefico M7.9.7, Bosch M7.9.7(+) (VAZ), Bosch M7.9.7+ (Geely cars, Amulet), Bosch M7.9.7.1 (Chevrolet Aveo), Bosch ME7.9.7 (Chery cars))
..
$11.71
Set of modules (General license):
Continental DC4 TCM
Continental TA2005 TCM
The modules are designed to read / write calibrations and programs of the DC4/TA2005 TCM ECU installed on Renault vehicles via the diagnostic connector.
Additional function:
Cal..
$66.45
License reference program SRSbook
..
$66.45
Переходник для Mercedes. Используется для соединения с авто Mercedes у которых 38-контактный круглый диагностический разъем.
Работает с устройствами у которых на выходе OBD-II разъём.
..
$3.36
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.80
Instead of a main cable + adapter OBDII-16
..
$23.92
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.53
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.66
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
License renewal ChipExplorer 2 for 1 year
..
$117.13
The module is designed ECU reprogramming IEFI6/ITMS-6F Daewoo cars via diagnostic connector GM-12
..
$41.05
CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary f..
$99.67
The module is designed for chip tuning Hyundai(IX35, IX55, Santa Fe, Tucson) and Kia(Carnival, Mohave, Sorento, Sportage) with diesel engines 2.0 CRDi (D4HA, 184HP), 2.2 CRDi (D4HB, 197HP) and 3.0 V6 CRDi (D6EB, 247HP).
Please note:
Third-party module developer! Technical s..
$106.32
FID: 64, 103
Service module for identification and virtual reading of the firmware control unit Denso 32920-4xxxx. The ECU is powered by a Renesas SH7052 CPU.
Read the actual flash memory of a given block is only possible by drilling a fairly large hole in the hull f..
$119.87
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$93.03
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
Supports reading and writing Mazda with CPU M32r 1.8/2.0/2.5 liters 2008+ with the ability to restore from any state
..
$66.45
Read/Write firmware
Read/Delete errors
Check/Fix the checksum
The module automatically determines the size. Supports all markets. Read a full Hour, recording 10-15 minutes of cars and trucks. Machinery is the ECU is written HOUR SH7059 processor.
Used processors SH7058, ..
$106.32
The module supports the TCM/M32R CVT [512 KB/896kb/1024kb] CAN
Identification
Read/Write calibration
Read/Delete errors
Recalculation of the COP
..
$93.03
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allows you to change the VIN code in the downloaded firmware.
..
$66.45
The module for the new version of the program Chiploader NG
Module [51] Bosch MEDC17 - Bench is designed to read and write the internal memory (flash and eeprom) of the processor is Tricore ECU Bosch MEDC17 on the table without disassembling the ECU.
Detailed information ..
$258.00
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
The price shown is for the owners of the Sirius module 3x
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allo..
$26.58
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module is designed to create dual-mode firmware with a fully customized set of calibrations for the second mode. There is a possibility of fuel pump disconnection in any of the modes (a small portion of the firmware may not support this feature). You can also set the delay of switching modes ..
$53.16
The module can read/write most of the Denso ECUs with processors SH7055, SH7058, SH7059.
Sample list of brands:
Nissan/Mazda/Mitsubishi/Suzuki/Opel/Subaru/Volvo/Range Rover
1)Read and write Full flash CPU SH705x.
2) More secure recording of modified blocks (e..
$132.89
Module 3 supports reading and writing of the following types of processors of the M32r series used in both the engine control unit and the active central differential control unit:
MH8104F_(512K) by CAN
MH8104F_(512k) by Kline (repair/restoration)
MH8106F_(1024K) by CAN
..
$93.03
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
Features of the module:
Write firmware
Read/Delete errors
Virtual reading
Check/Fix the checksum (the bypass digital signature)
Tabs:
CAN - for Master ECU
Slave To record a second engine ECU (Slave)
Stock - to return to the flow without using th..
$132.89
The module allows you to view, edit, compare the firmware files of Foton, JAC cars with Cummins engine with the Continental CM2880 control unit.
It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader.
The module contains more than 1000 b..
$332.24
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set ..
$106.32
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Available to all users free Module Jan 7.2+ module 1.
Key features:
Edit the calibra..
$33.22
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
The module is designed to read and write FLASH memory of ECU MT86 installed on a KIA/Hyundai. Working with these types of ECU's is via the J2534 device
ECU MT86 is a read only field calibrations. Recording is supported for the following formats:
Firmware reads th..
$42.41
The program in Russian and English languages.
Universal programmer a large number of microcontrollers from Microchip, Atmel, Cypress, ST, etc., and also chip FLASH/EEPROM (currently more than 13000 chips). Connect to PC and power to the programmer through the USB port of the computer (5v).
..
$122.08
A comprehensive package brands ScanDoc - complete package brands for ScanDoc ScanDoc scanners and Compact. The package also opens a brand under development.
The coverage map on marks you can see on the developer's website →.
The module opens with one click via the Internet. Re-download th..
$784.08
The module is designed to read and write FLASH memory of ECU Siemens 5WY (5 connectors, cars KIA, Hyundai) Siemens 5WY SIMK31 (2 connectors, cars Chery QQ) Siemens MS43 via BootStrapLoader.
..
$29.80
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
The module is intended for cloning on the table, without parsing the ECU. Supported and filled in TCU in a metal case and not filled in a plastic housing.
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
..
$132.89
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$53.16
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$53.16
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$106.32
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$106.32
The module allows you to view and edit statistics (mileage, fuel consumed), speed limit and transmission protection parameters in the configuration files *.cfg ECU Continental CM2150, CM2200, CM2220, CM2350, CM2880.
Read using the Combiloader programmer by the Cummins CM2xxx module. It is pos..
$239.21
CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1.
Power supply.
To work CombiBox must submit the stabilized voltage..
$93.03
![[54] BOSCH ME17.8.8 - OBD2](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[54] BOSCH ME17.8.8 - OBD2")
