The modules allow chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with Abit M240 and M240S1 (CAN) ECUs.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the cont..
$265.79
This module allows chip tuning of diesel trucks and commercial vehicles, as well as construction equipment equipped with the Abit M240 ECU.
Programming of the ECU is carried out using the CombiLoader loader.
Research with the help of reverse engineering of the control program a..
$332.24
The module is designed to work with blocks of variable-speed drives and automatic transmission that are installed on Mitsubishi vehicles, supported by reading and writing.
CVT Lancer X/ASX 1.8/2.0L, Outlander XL/3 2.0/2.4L (MH8104F/512KB MH8106F/1MB) [RD/WR/CK]
AT Pajero Sport (2010..
$132.89
The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles.
Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors.
..
$132.89
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
The module is designed to work with ECU Denso processors R7F701202/R7F701216 working on Protocol P5-UDS installed with gasoline engines in Toyota/Lexus cars. Supported read, write, review, and correction of the COP. Currently supported cars Lexus ES250, LS500, UX, as well as some hybrid vehicles ..
$132.89
The module is designed to work with ECUS that are installed in vehicles with Ford diesel engines 1.4, 1.5, 1.6 l Supported read, write, review, and correction checksums.
Ford Focus 3: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
Ford Mondeo 4: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]
..
$93.03
The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles.
Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available.
..
$199.34
Set of modules (General license):
Continental DC4 TCM
Continental TA2005 TCM
The modules are designed to read / write calibrations and programs of the DC4/TA2005 TCM ECU installed on Renault vehicles via the diagnostic connector.
Additional function:
Cal..
$66.45
The module is designed for chip tuning of Geely vehicles equipped with DSI TCM automatic transmission.
Module Features:
Limited module with a limited number of calibrations!
The module calculates the COP.
Hardware versions 02F and 02R are supported.
Suppor..
$93.03
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$93.03
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
For programming ECU VS-5.6, you must use a special adapter, the cost of the adapter is included in the cost of the module. Required shipping of the adapter to the user.
The vehicles are equipped with ECU ITELMA VS-5.6.
..
$33.22
Module prednaznachen to work with blocks EDC17C08 and EDC17CP14 that were installed on vehicles Kia/Hyundai with a diesel engine capacity of 1.6-2.2 l, with a level of protection TPROT3. The ability to write the modified firmware in the ECU EDC17CP14 c TPROT11. Maintains a record (as complete fil..
$93.03
This module allows you to make chip-tuning of cars GAZ and UAZ vehicles that equipped with ECU Mikas-11, Mikas-11CR, Mikas-11ET, VS-8.
Supports the following versions:
The number of the ECU and firmware version of the ECU
824.3763.001-05 0789_101
821.3763.000-01 0..
$66.45
License 60, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
&..
$132.89
The module is designed to work with the Denso ECU with the R7F702002 microcontroller installed in Toyota and Lexus vehicles with 3.5T (V35A-FTS) and 2.4T (T24A-FTS) gasoline engines from the 2022 model year (Toyota Tundra/Tundra Hybrid/LC300/Highlander, Lexus NX350/RX350/LS500/LX600). Reading and..
$199.34
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E83.
Examples of vehicles equipped with this type of ECU: Opel Astra J A16XER, A18XER Opel Astra J, Opel Astra J A16LET, Opel Corsa D A12XER, A14XER Opel Corsa D, Opel Insignia A16XER, A18XER ..
$159.47
License 44, may be applicable at the discretion of the licensee (user) to the work:
Read/Write FLASH processors SH7058,SH7059,R4F70580, R4F70590 (without recalculation of checksums).
Read/Write Opel EEPROM
Read/Write Mitsubishi EEPROM
Read/Write Suzuki EEPROM
Readi..
$106.32
It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the..
$93.03
License 52, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Rec..
$132.89
Attention! This module works in conjunction with CombiLoader 2.16 or later.
The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector.
The module automatically corrects CS calibrati..
$66.45
The module is designed to work with engine control units, automatic transmission and hybrid installation of Toyota/Lexus/Scion/Hino vehicles via CAN bus and K-line. There is a virtual reading function for ECUs operating over the K-Line and CAN-bus protocol (if there is a corresponding file on the..
$132.89
License 57, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by BOSCH:
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 24c16
..
$106.32
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
$119.87
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
$239.73
Module Visteon ESU-131 5M51/8M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2005 to 2007.
Supported versions:
5M51JD (2005)
5M51JE (2006)
5M51RC (2005)
5M51RE (2006)
5M51RF (2006)
5M51SC (2005)
..
$132.89
License 54, may be applicable at the discretion of the licensee (user) to the work:
The module works with the M86 blocks for VAS and ITELMA installed on UAZ and UAZ cars.
This module operates in two modes, CAN and K Line.
1. CAN mode(on the car or dire..
$66.45
License 110, may be applicable at the discretion of the licensee(user) to work
with: Bosch M(E) ECU17.9.7 gasoline engines installed on UAZ and UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(reading the full FLASH content when directly connected ..
$66.45
Distribution of licenses after 08/31/2024!
License 145, may be applicable at the discretion of the licensee (user) to work with:
Simos 3x/7x/9x ECUs installed on VAG vehicles, which allows for full-fledged repair and restoration work with these ECUs.
Reading FULLFLASH
..
$106.32
License 138, may be applicable at the discretion of the licensee (user) to work with:
ECU EGS gasoline engines installed on UAZ vehicles.
Identification
Reading/Clearing the DTC
Reading FLASH(full content)
FLASH recording (control program + calibration area or ..
$66.45
Includes maps calibrations for all firmware M74, М74CAN and М74к.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the..
$53.16
The cars of Chinese production (Great Wall Hover, BYD, etc.) with Delphi MT20U ECU, MT20U2, MT20UED, MT22U and MT22.1. Supported read and write FLASH and EEPROM.
..
$93.03
License 58, may be applicable at the discretion of the licensee (user) to the work:
The module works with BCM manufactured by CONTINENTAL.
Reading the Full Flash of the NEC processor(RENESAS).
Full Flash recording of the NEC processor(RENESAS).
Reading EEPROM 95..
$106.32
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
$239.73
The module is designed to work with ECU Denso installed on vehicles JLR. Supported read, write, review, and correction checksums.
Jaguar XF/XJ/XK (X250/X350/X351/X150) 3.0L V6, 3.5L V8, 4.2L V8/SC (Denso) [RD/WR/CK]
Range Rover/Sport/Discovery 3 4.0L V6, 4.4L V8, 4.2L V8/SC (Denso) ..
$119.61
The module is designed for operation with control units petrol engines and turbo diesel installed in vehicles Land Rover Freelander 2, Evoque, Discovery Sport etc. Supported read, write, calibration, validation and correction of the COP.
Discovery 3 2.7L TDV6 (SID201/SID204) [RD/WR/CK]
..
$159.47
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
$239.73
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH7058 and SH7059.
Supported filesize - 1Mb and 1.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Targ..
$239.73
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
Work with ECU Hitachi processor SH72533 installed on modern vehicles X-Trail, Qashqai, Juke, Teana, Murano, Patrol, Pathfinder and others with the 2014-2016 model years. The type definition module, read and write calibration check/correction checksums.
EFI SH72533 Gen 2 (2014+) Calibratio..
$66.45
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
$239.73
The modules are designed for reading and writing the SIMOS12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECU installed on VAG vehicles.
Work with the SIMOS12.1/12.2 ECU is performed on the table without opening the ECU.
Работа с ЭБУ SIMOS16.11 is performed on the table with the ECU openin
..
$199.34
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.73
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
$179.80
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
$299.66
The module is designed to work with ECU Bosch MG1, set c petrol engines in Ford vehicles. Supported read, write, review, and correction of the COP.
Ford F-150: 3.5L Ecoboost V6 (MG1CS015) [HL3A] [RD/WR/CK]
Ford Fiesta 8: 1.5L Ecoboost MT (MG1CS016) [JX6A] [RD/WR/CK]
Ford Focus..
$132.89
The modules are designed to read / write ECU Continental SIM2K-250/251/253/260/261 that are installed on vehicles Hyundai/Kia.
No need to opening the ECU. In diagnostic mode the available functions of identification, read/clear faults and recording and/or calibrations.
The mo..
$132.89
The module is designed to work with the ECU engine 1.0 TSI, 1.2 TSI, 1.4 TSI, 1.6 MPI, 2.0 TSI, 3.6 FSI, 1.0 MPI, etc. installed on vehicles group VAG (VW Golf 7, Polo, Passat B8, Skoda Rapid, Octavia A7, Tiguan, Jetta, Audi A1, A3, etc.). Supported entry, verification and correction of the COP.
..
$119.61
The module is designed to work with the ECU SID208 installed on vehicles with diesel engine 2.2 l Supported read, write, razblokirovka the ECU to record the modified firmware, and test and correction checksums.
Citroen/Peugeot 2.2 L HDi (SID208) [WR/CK] (write after unlocking in BSL)
..
$93.03
The module is designed to work with blocks motor control EMS3130, EMS3132, EMS3134 used in vehicles Renault, Dacia, Nissan. Supported reading and writing as control unit as a whole, and only in the area of calibration, validation and correction checksums, ability to work with files in formats oth..
$66.45
The module is designed to work with blocks EDC16C39, which are installed on vehicles UAZ Patriot, hunter with diesel engines ZMZ and Iveco. Supported reading calibrations (for Iveco), a record full of files (and calibration for the Iveco), verification and correction checksums.
Patriot/Hu..
$66.45
The module is designed to work with ECU Mitsubishi and Denso installed with gasoline engines in vehicles Mazda with the 2019 model year. Supported read, write, review, and correction of the COP.
1.5L, 2.0L, 2.5L SKYACTIV-G P5/PA/PE/PY MY2019 (Mitsubishi) [PYFA] [RD/WR/CK]
1.5L, 2.0L..
$93.03
Module kit:
The module is designed to read/write FLASH memory of DSI TCM ECUs installed on SsangYong/Geely vehicles via the diagnostic connector. The module performs automatic correction of the COP of calibrations during recording.
The module is designed to write software / calibrat..
$93.03
The module is designed to work with ECU Bosch MED17.7.1/MED17.7.2/MED17.7.5/MED17.7.3/MED17.7.3.1, EDC17CP01/EDC17CP10 (with external flash), EDC17CP46/EDC17CP57/EDC17CP60/EDC17C66 installed on vehicles from Mercedes-Benz and Infiniti some. Supported reading (only for blocks EDC17), entry, valida..
$159.47
The module is designed to work with the ECU built on microcontrollers SH72513/SH72543/SH72544 installed on diesel vehicles of different brands. Supported read, write, and recalculation of checksums.
Kia/Hyundai 2.5 L CRDI (DCM3.7AP) [RD/WR/CK]
Opel/Chevrolet 2.0 L, 2.2 L CDTI (DCM3...
$132.89
The module is designed to work with ECU Bosch EDC17CP27/EDC17C49/EDC17C79 installed on vehicles of Jeep. Supported read, write, review, and correction checksums.
2.8 L CRDI (EDC17CP27)[RD/WR/CK]
3.0 L CRDI (EDC17C49/C79) [RD/WR/CK] read-may require direct connection to the ECU
..
$93.03
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.45
The module is designed to work with the ECU EMS3155, SID309, Hitachi CPU RH850 working on the UDS Protocol and installed in vehicles with petrol engines 1.2 l and diesel 1.5 l Supported read, write, review, and correction checksums.
1.2 T EMS3155 UDS (TC1782/2.5 MB) [RD/WR/CK]
1.5 L..
$132.89
The module is designed to work with the ECU from diesel engines 1.6, 2.0, 3.0 and 4.2 TDI are installed on passenger cars and crossover vehicles group VAG, approximately 2010. Supported entry, verification and correction of the COP.
2.0L, 3.0L TDI (EDC17CP04/EDC17CP14/EDC17CP..
$119.61
The module is designed to work with blocks motor control EDC16CP31-6 and EDC16CP31-8, installed in the vehicles of MB Sprinter 906/909 (Classic). Supported read, write, calibration, validation and correction of the COP.
Sprinter (906) CDI 2.2 L (EDC16CP31-6) [RD/WR/CK]
Sprinter Clas..
$93.03
The module is designed for operation with control units SIMK-41/43, SIM2K-47 used in vehicles Kia/Hyundai. Supported reading (when available), entry, checking and correction of the checksum, automatically detect the type of ECU.
2.0 L, 2.7 L K-Line (SIMK-41/43) [RD/WR/CK]
2.0 L, 2.4..
$66.45
Work with ECU Denso processors SH7058, SH7058S and SH7059 installed on vehicles Mitsubishi. Automatic detection of module type, read, write, verification/correction checksums.
Denso Diesel (SH7058/SH7058S/1MB SH7059/1.5MB SH72543/2MB) [RD/WR/CK]
..
$93.03
Supported reading (where possible), write via OBD and correction KS for vehicles with engines of 1.1, 1.4, 1.6 liters.
Kia/Hyundai: 1.4L, 1.6L (ME17.9.11/12/13) [RD/WR/CK]
Kia/Hyundai: 1.4L, 1.6L (ME(G)17.9.21/17.9.21.1) [RD/WR/CK]
Kia/Hyundai: 1.6L, 3.0L (ME17.9.2/ME(D)(G)17...
$93.03
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
The Bosch EDC7UC31 KAMAZ module is designed for chip tuning of KAMAZ vehicles with diesel engines of the KAMAZ-740 family.
Supported firmware (software versions P702.141, P986.310), EDC7UC31 KAMAZ module:
702V141_740.60-360-290812_5460-4010142-01
702V141_740.60-360-29..
$265.79
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E78.
Examples of vehicles equipped with this type of ECU: Opel Astra J A14NET, A14NET Opel Opel Corsa C, Opel Mocca A14NET, A14NET Chevrolet Cruze, Chevrolet Tracker A18XER, Chevrolet Malibu A..
$132.89
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.32
Module DL501 designed for chip-tuning VAG cars (Audi and other vehicles VAG with longitudinal engine).
Please note:
Modules a third-party developer! Technical support from the author of the module (V. Kulikova).
Modules are independent from each other and are ..
$132.89
Set of 15 modules Toyota Denso Diesel 1,2,3,4,5 + 1,2,3,4,5,6 Petrol + turbo Petrol + OLD + Gearbox+ GT86. Allows you to edit all the available vehicles Toyota, Lexus, Scion, Hino on the units of DENSO.
15% savings when ordering.
..
$3 769.77
The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$132.89
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
FID: 280
Module for reading and writing by CANbus Isuzu diesel vehicles with Transtron ECUs based on Renesas SH7058, SH7059, SH72533 and SH72544.
Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)
Family for Transtron ECUs based on MCUs Renesas SH7058/SH7059/..
$179.80
Support vehicles: Chevrolet Captiva
..
$29.35
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
$239.73
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
$119.87
License 70, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Full Flash file, read in BSL mode or by a programmer.
Wor..
$106.32
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
For chip tuning Hyundai vehicles equipped with KEFICO ECU or Bosch 7.9.7.
..
$66.45
For chip-tuning KIA vehicles equipped with KEFICO ECU or Bosch 7.9.7.
..
$66.45
This module allows you to produce a chip tuning Daewoo vehicles equipped with the GM DELCO ECU ITMS-6F IEFI and-6. The module works in conjunction with ChipTuningPRO 6.74 or higher.
..
$26.58
The Toyota Denso Diesel 4.5D (1VD-FTV) module with 76F0070 processor is designed for chip tuning of Toyota cars with 4.5L diesel engines, Denso ECU.
Pay attention:
A third-party developer module! Technical support from the author of the module (V. Kulikova).
Supported..
$239.21
Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of..
$53.16
Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware.
Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/butto..
$79.74
License 49, may be applicable at the discretion of the licensee (user) to the work:
Disabling the immobilizer function for troubleshooting and checking the ECM during repair.
The work is done by upgrading the Flash file.
Works as an editor.
Recalculates checksums.
..
$132.89
The module allows you to produce professional chip tuning motorcycles, the Delphi MT05 ECU (firmware size 128 KB) and Delphi MT05.2 (firmware size 256 KB).
The programming of this ECU is using the module Delphi MT-05 loader CombiLoader.
Deep research (reverse enginee..
$132.89
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
License 17, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording EEPROM 24c04 or 93c56 (depends on the type of panel) by OBDII or direct connection on the table (connection in the help).
Correction of odometer readings by OBDII or direct connecti..
$66.45
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
$239.73
The module is designed to work with variator control units installed in Subaru vehicles.
..
$93.03
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
$167.81
For chip-tuning cars Mitsubishi Lancer 10 (except vehicles with engines of 1.5 L).
..
$79.74
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
$179.80
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.73
License 29, may be applicable at the discretion of the licensee (user) to the work:
Recording the mileage of dashboards on EEPROM 95040 cars before 2011
Recording the mileage of dashboards on EEPROM 95160 cars after 2011
Universal module, works with a large numbe..
$79.74
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
$239.73
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.74
Software module for editing calibrations Transtron ECUs of diesel Isuzu vehicles. MCU supported SH72533 and SH72544.
Supported filesize - 2Mb and 2.5Mb.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Targe..
$239.73
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
Module Visteon ESU-411/418 7M51 designed for chip-tuning Ford Focus II and C-Max with engine 1.8 and 2.0 L, model years 2007 and 2012.
Supported versions:
7M51AAG (2010)
7M51ABA (2007)
7M51ADA (2007)
7M51ABC (2008)
7M51ACD (2009)
7M51ADE (2009)..
$132.89
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.61
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
The module is designed to work with the ECU automatic transmission installed in some vehicles, the Kia/Hyundai. Supported read, write, review, and correction of the COP.
Kia/Hyundai: MG7.9.8/MEG17.9.12 Gearbox (ST10F275/TCU) [RD/WR]
TC14 Gearbox (MPC562/TCU) [RD/WR/CK]
TC60/TC..
$93.03
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
$359.60
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
$179.80
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
$239.73
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$66.45
The module is designed for reading and writing FLASH and EEPROM of the M74.9 259.3765 004-11 ECUs of GAZ vehicles with ITELMA software, based on Artery series AT32F4xx processors (ARM architecture). Working with the ECU is done without disassembling it. M74.9 GAZ firmware is saved only in SMS-Sof..
$119.61
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.34
Module 'China MT80 ECU - OBDII' is designed to read and write FLASH memory of ECU MT80 installed on Chinese vehicles through J2534 device and KLine adapter.
Supported the conversion and checksum. Recording is performed only in the area of calibrations.
For holders of CHIPSOFT J..
$93.09
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
$239.73
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
$239.73
The module allows for professional chip tuning of Gazelle vehicles with Evotech 2.7L engines from the 2024 model year and newer with electronic throttle pedal (EGAS), equipped with the latest ECU M74.9.1. There are over 1000 calibrations available for editing the M74.9 control system, providing v..
$159.47
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.60
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
$239.73
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.66
Includes all the module 1, the calibrated dual-mode firmware 6.38 M74 and map editing dual-mode firmware.
..
$106.32
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
The Bosch MG1CS201 module (DME83Tx, DME84Tx, DME86Tx, DME88Tx, DME8CT) is designed for chip tuning BMW and MINI vehicles with gasoline engines B38xx, B46xx, B48xx, B58xx, N63xx, N74, and S63xx. It is compatible with: - BMW 2 Series F22, F23, F44, F45, F46, and G42 - BMW 3 Series G20 and G21 - BMW..
$664.47
The Bosch MG1CS003 module (DME840, DME840H, DME841, DME841H, DME860, DME861, DME880, DME8C0) for BMW is designed for chip tuning of BMW vehicles with N63xx, N74xx, B46xx, B48xx, and B58xx gasoline engines. It is compatible with the following BMW models: - 1 Series F20 - 2 Series F22 and F23 - 3 S..
$332.24
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
$287.68
The Ford EDC17CV41 module 24 allows you to view, compare and edit firmware files of Ford Cargo F-Max vehicles (Bosch EDC17CV41 ECU).
Calibrations are available for editing: boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phases, torque limits, ..
$398.68
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
Module for motor vehicles GAS, SHAANXI, FAW with the control units EDC17CV44/54 using Mscan EDS-24.
..
$66.45
Module Ford ECU Siemens SIM28/SIM29/SIM210/SIM22 / EMS2204 / SID206, Visteon ESU-131/411/412/415/418 - OBD2 is designed to read and write FLASH memory of ECU Siemens SIM28, SIM29, SIM210, SIM22, EMS2204, SID206, Visteon ESU-131/411/412/415/418 - OBDII Ford vehicles.
The mod..
$48.98
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
The module supports the TCM/M32R CVT [512 KB/896kb/1024kb] CAN
Identification
Read/Write calibration
Read/Delete errors
Recalculation of the COP
..
$93.03
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
The module allows to make the chip tuning Opel and Chevrolet vehicles that equipped with ECU ACDelco E83.
Examples of vehicles equipped with this type of ECU: Opel Astra J A16XER, A18XER Opel Astra J, Opel Astra J A16LET, Opel Corsa D A12XER, A14XER Opel Corsa D, Opel Insignia A16XER, A18XER ..
$106.32
FIDs: 155, 157, 177
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.
Renault Siemens SID301 (FID:157)
This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0..
$239.73
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
$239.73
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
$239.73
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
$299.66
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
$239.73
License 142, may be applicable at the discretion of the licensee (user) to work:
with Bosch ME7.6.x ECUs installed on GM vehicles, allowing for full repair and restoration work with these ECUs.
Reading FULL FLASH (BENCH/OBD)
Writing FULL FLASH (BENCH/OBD)
Reading EEPROM (B..
$79.74
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
FID: 238, 242, 245, 246
Module for reading and writing control unit Denso installed on diesel vehicles with engines Mazda SkyActiv-D.
Mazda Diesel Denso Gen3 SH72543 (FID: 246)
The control unit is powered by a processor Renesas SH72543 with internal flash memory ..
$239.73
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
$123.57
Supports reading and writing Mazda with CPU M32r 1.8/2.0/2.5 liters 2008+ with the ability to restore from any state
..
$66.45
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.22
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.74
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
License 137 may be applicable at the discretion of the licensee (user) to work with:
TCM ECU automatic transmission 6L50 installed on UAZ Patriot vehicles.
Identification
Reading/Clearing the DTC
Reading/VIN entry
FLASH recording(calibration area)
T..
$132.89
Diagnostic cord for diagnostics of cars BMW F-Series. The device connects to the network card of the PC or laptop and doesn't need any special adapters. To work with the scanner PC must be installed specialized software BMW ISTA/D Rheingold E-SYS. Software not included.
Functionality:
..
$20.38
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP..
$119.61
Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware.
Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibrati..
$119.61
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set ..
$106.32
Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware.
Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Typ..
$79.74
Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine ..
$79.74
Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of..
$79.74
Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware.
Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals o..
$119.61
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware.
Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine..
$26.58
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
