The module is designed to read/write SDI4/6/7/8 ECUs installed on Porsche vehicles.
Work with the ECU can be done both through the diagnostic connector of the car, and on the table without opening the ECU. Identification and read/reset error functions are also available.
..
$199.34
Designed to read/write calibration and program the ECU Delphi DCM6.2/6.2A/6.2C installed on the Peugeot/Citroen via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identi..
$93.03
Universal scanner Lexia 3 software Diagbox allows you to perform computer diagnostics of all models from car brands such as Citroen, Peugeot release since 1995. Diagnosis is made through a standard sixteen pin connector OBD II for modern cars or through a special 30-pin connector (not included) i..
$123.76
The set of modules (General license):
Delphi DCM3.7 SsangYong
Delphi DCM3.7 GM
Delphi DCM3.7 GreatWall
Delphi DCM3.7 Hyundai/Kia
Delphi DCM3.7 VAG
The modules are designed to read / write FLASH memory of ECU Delphi DCM3.7, mounted on SsangYong, Opel, Chevrole..
$132.89
The modules are designed to read / write ECU Continental SIM2K-250/251/253/260/261 that are installed on vehicles Hyundai/Kia.
No need to opening the ECU. In diagnostic mode the available functions of identification, read/clear faults and recording and/or calibrations.
The mo..
$132.89
The scanner Scandoc Compact modern device for the in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the sensors, con..
$423.93
The module is designed to read / write the ECU SIM271DE 2.0 installed on Mercedes-Benz vehicles.
Work with the ECU can be made via the diagnostic connector of the car and on the Desk without opening the ECU. There are also features of identification and reading/clearing errors.
..
$132.89
OBD 2 ELM327 USB adapter is designed for diagnostic scanning of vehicle systems and the analysis of the main operating parameters – rpm and engine temperature, speed, system voltage and condition sensors. Self-diagnosis is performed by means of a computer. This adapter is equipped with a USB cabl..
$12.99
It is designed for chip tuning of the Delphi MT22.3/22.5 ECU via the CAN bus via the diagnostic connector.
It is designed for chip tuning of the Delphi MT 62.1 ECU via the diagnostic connector.
Pay attention:
Delphi MT22.5 ECUs have two different hardware modifi..
$66.45
Diagnostic cord for diagnostics of cars BMW F-Series. The device connects to the network card of the PC or laptop and doesn't need any special adapters. To work with the scanner PC must be installed specialized software BMW ISTA/D Rheingold E-SYS. Software not included.
Functionality:
..
$20.38
Designed to read and record the calibration and program the ECU SID208 vehicle Peugeot Boxer/Citroen Jumper via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
Identification of control UNIT: allows you to request identifica..
$132.89
Portable scan tool ELM 327 WIFI – suitable for advanced motorists and workers car. Allow read and delete errors of engine, take the operating parameters of the engine, and can turn your mobile phone (Apple or Android) to the onboard computer.
The advantages of ELM 327 WIFI :
very sma..
$29.12
The scanner Scandoc Compact Full — modern instrument for in-depth vehicle diagnostics. Works with a large number of automotive brands, has a simple and user-friendly interface and allows you to perform all the basic diagnostic operations: read and reset error information, show data from the senso..
$1 194.72
The module is designed for operation with control units new generation engines, built using microcontrollers 76F0196/198/199/219. Supported entry, verification and correction of the CK, and for units employing the new Protocol P5 - reading of the internal flash via the OBD. Virtual reading is ava..
$132.89
License 117, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Bosch SRS units based on the Renesas RH850 R7F7010643 MK installed on Subaru Forester cars, which allows for full-fledged repair and restoration work ..
$79.74
Module for the new version of the Chiploader NG program
Module [53] Mercedes Delphi CRD - OBD2 is designed for reading and writing by diagnostic method of ECU Delphi CRD.11, CRD2.xx, CRD3.xx (only with Tricore TC1797) installed on Mercedes cars.
..
$98.18
The MITSUBISHI module is a software package for diagnostics of cars MITSUBISHI using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The module is designed to work through the diagnostic connector of a car with DSG and automatic transmission units used in VAG concern cars. It supports reading (virtual), writing, checking and correcting checksums.
DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]
AL420/AL600 (09L/09E) K-Line..
$132.89
Module MERCEDES / SMART - software package for diagnostics of cars MERCEDES / SMART with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
It is designed for reading/writing calibrations and programs of the Delphi DCM6.2AP ECU installed on GreatWall/JAC vehicles via the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the..
$93.03
The module is designed to work through the diagnostic connector of the car with transmission control units 6HP26, 5R/6R/6F/8F/10R of various modifications used in Ford cars. Supports reading, writing, checking and correcting checksums.
6HP26 TCM [RD/WR/CK]
5R110 TCM [RD/WR/CK]
..
$119.61
The module allows you to write firmware diagnostic method, without removing the ECU from the vehicle through the DLC (to work with the ECU on the car must be connected directly to the connector of the UNIT to disassemble the unit is not required).
Support ECU Bosch MSE3.0, M7.9.7, ME7.9.7, M7..
$66.45
Module ACDelco Delphi intended read / write FLASH memory of ECU Delphi ACDelco E37/E38/E39/E67/E78/E83 installed on Chevrolet and Opel via the diagnostic connector.
Table of applicability ACDelco E37 (2.4 L — LE5/LE9):
Chevrolet Captiva (C140) 2011+
Opel Antara 2011+
..
$119.61
The modules are designed to read and write FLASH memory of ECU installed on the car Citroen/Peugeot, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
Extra features:
Identification of control UNIT: allows you to request identification data of ..
$66.45
License 47, may be applicable at the discretion of the licensee (user) to the work:
Identification of BCM(CCBS).
Reading/Clearing fault codes.
Reading/Flash recording (program area + calibration).
Changing the VIN number.
Resetting the CCBS to the VIRGIN(NEW) state..
$132.89
License 83, may be applicable at the discretion of the licensee (user) to the work:
MK Renesas RH850 R7F701400 in the Continental instrument panels installed on Renault, Dacia cars via the diagnostic connector or on the table (connection in the help).
MK Renesas D70F3525 in..
$106.32
The adapter is designed to connect the personal computer and the vehicle's control systems, compatible with ISO-9141(K, L –line) or ISO14230 (KWP2000, in electrical terms similar to the ISO-9141). Works with passenger vehicles in the network 12V.
The diagnostic complex based on a regular PC u..
$17.14
The Valeo V4X module is designed to read and write the FLASH memory of the Valeo S3000/V40/V42 ECU installed on Renault cars through the diagnostic connector.
The Sagem S3K module is designed to read and write calibrations and the program of the Sagem S3000 ECU (512k FLASH) install..
$66.45
Module supported:
Read/erase error codes
Verification and recalculation of the checksum (CS)
Identification
Entry
Reading
For the following ECU's:
BRZ SH72531 [1280k] CAN 2013+
SH7058 [1024k] CAN 2007+
SH7058 [1024k] K-line 2003+
SH7..
$106.32
Module OPEL / VAUXHALL software for diagnostic of OPEL and VAUXHALL with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehi..
$62.46
The module allows you to view, edit and compare the DTC error mask of Kamaz vehicles with the Mersedes engine control unit MR PLD SW 24C.
Decryption of error codes according to the manufacturer's standard. It is possible to search for the fault code by the error number, the full decryption of..
$106.32
BMW INPA K+D CAN USB — a unique diagnostic complex, consisting of software and a special adapter that works with the original BMW.
With the car adapter, BMW INPA K+D CAN enables full-featured vehicle diagnostics, adaptation of units, coding and programming the entire range of BMW vehicles. BM..
$36.12
This module allows to make the chip tuning Hyundai and KIA vehicles that equipped with ECU Bosch M(G)7.9.8 or KEFICO.
Supported versions:
PM98A440K
PM98A442G
PM98A533O
PM98A742J
PM98A833F
PM98A833H
PM98A833J
PM98A833K
PM98A833..
$106.32
Module for SUZUKI is a software package for diagnostics of cars of the SUZUKI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The BMW cars with ECU Siemens MS41/42/43: E36/E38/E39/E46/E53 6-cyl 2.0 L — 3.0 L. ECU Programming can be performed directly on the vehicle through the diagnostic connector.
..
$66.45
Chevrolet Spark M300, TagAz Vega C-100. Designed for read-write calibrations and programs the ECU via the diagnostic connector.
..
$18.61
RoadPartner cars TagAz/TaGeR/SsangYoung Rexton with engines 2.3/2.8/3.2 L. Intended for read-write FLASH memory via the diagnostic connector.
..
$66.45
Chevrolet (Lacetti, Epica, Tacuma, Rezzo), Daewoo (Matiz). ECU programming can be performed directly on the vehicle through the diagnostic connector.
..
$93.03
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
$179.80
Development of the module is not over
Functionality you can see in the coverage map.
Module for FIAT / ALFA-ROMEO / LANCIA - software for vehicle diagnostics FIAT / ALFA-ROMEO / LANCIA with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the ..
$62.46
License 66, may be applicable at the discretion of the licensee (user) to the work:
Allows you to work via the OBDII connector on the CAN bus with ABS/ESP BOSCH 9.0-9.1 units based on TMS470 microcontrollers,
TMS570 with EEPROM 95128/95320/95640 chips installed on Renault, Dacia, Ni..
$159.47
The module is designed to work through the diagnostic connector of a car with Delphi DCM6.2 engine control units used in VAG concern cars. Virtual reading, writing, checking and correction of checksums are supported.
1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/RD/WR/CK]
..
$132.89
Designed for chip tuning of ECU Abit M20.20, M20.21, M240, M240S1, MD22. Modules allow you to: - Read and write calibration area - Read and write control program - Calculate and, if necessary, automatically correct the checksum of the calibration area - Perform ECU identification - Read and reset..
$132.89
Module for the new version of the program Chiploader NG
The module [55] Mercedes Bosch EDC17-OBD2 is designed to read the calibration area and write the calibration area by the diagnostic method of the ECU EDC17CP01 (only ECU with external Flash), EDC17CP10 (only..
$169.64
License 87, may be applicable at the discretion of the licensee (user) to the work:
With MK Renesas RH850 R7F701404, NEC 70F3529, NEC 70F3532 in the panels of Continental VDO devices installed on Haval H6/H9/F7 cars via the diagnostic connector or on the table (con..
$106.32
The module is designed to work with DCM6.2AP, DCM7.1AP ECUs installed on Chinese-made cars via a diagnostic connector. Supports reading, writing, checking and correcting checksums.
Changan 2.0L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng 2.3L TD (DCM7.1AP) [RD/WR/CK]
Dongfeng/Yucha..
$132.89
The module is designed SIMTEC70 read / write FLASH memory of ECU Siemens SIMTEC70, installed on Opel cars via diagnostic connector.
Table of applicability ECU SIMTEC 70:
Opel Astra G (1998-2000) X18XE1/X20XEV
Opel Vectra B (1998-2001) X18XE1/X20XEV
Opel Zafira (..
$119.61
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$212.63
The module is designed to work with the CRD3/CD3 ECU installed in Mercedes Benz cars. Work is supported through the diagnostic connector and "on the table". Supports reading, writing, checking and correcting checksums. It is possible to clone the ECU.
Mercedes-Benz CRD3/CRD3P FLASH [RD/WR..
$93.03
Module VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ - a software package for diagnostics of cars of mark VAZ / GAZ / UAZ / IJ / MAZ / KAMAZ / ZAZ with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it n..
$62.46
License 56, can be applied at the discretion of the licensee (user) to work:
The module allows you to work with the ACDelco E78 ECU in OBD II Mode, Bench Mode and Recovery mode.
1.OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Err..
$106.32
Module for the new version of the program Chiploader NG
The module [54] Bosch ME17. 8. 8-OBD2 is designed to read and write the diagnostic method of the calibration area of the ECU ME17.8.8, installed on various Chinese cars.
Detailed informatio..
$16.96
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$132.89
The modules are designed to read/write FLASH memory of ECU families Bosch MEDC17 Hyundai/Kia via the diagnostic connector.
Is free app for all users 2 or 3 version of module BSL TC17xx J2534.
Module Bosch MEDC17 Hyundai/Kia supported the following types of EC..
$106.32
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
The modules are designed to read/write FLASH memory of ECU Bosch MEDC17 and write FLASH memory of ECU SID807 cars Peugeot/Citroen via the diagnostic connector.
The modules support the following types of ECUS:
Bosch EDC17C10 (CPU TC1797)
Bosch MED17.4 (CPU TC1766)
..
$66.45
ECU Siemens SIM2K C201/241/242/245 used cars Hyundai, Kia, SsangYong.
Module allows read/write FLASH memory diagnostic tool, without removing the ECU from the vehicle.
Works through the J2534 interface.
ECU Siemens SIM2K 140/141/341/D160 applies to the Kia (Magentis, Cerato..
$93.03
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$106.32
The program works only with a usb key that is the same for all modules. A key without modules is not for sale.
Activation of modules with a USB key is 1-24 hours on working days.
Modern and convenient software for editing vehicle calibrations, designed to study the proc..
$39.87
The modules are designed to read / write FLASH memory of ECU MagnetiMarelli group cars via diagnostic connector using J2534 devices.
The modules support the following types of ECUS:
MagnetiMarelli MM4HV: petrol engines 1.4 l BUD, BXW, CGGA, CGGB.
MagnetiMarelli MM7GV:..
$66.45
Module NISSAN / INFINITI is a software package for diagnostics of cars of NISSAN and INFINITI vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions o..
$62.46
The HYUNDAI module is a software package for diagnostics of cars of HYUNDAI brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module for Peugeot - a software package for diagnostics of cars of the Peugeot brand with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module is designed to work with the ECU of production of Denso processors SH7055/SH7058/SH7058S/SH7059 installed in cars with petrol and diesel engines, primarily of Japanese manufacture - Mitsubishi, Nissan, Subaru, Suzuki. Work on the CAN bus, 'on the table' or in the car (in the presence o..
$132.89
License 80, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on Ford/Mazda cars,
which allows for full-fledged repair and restoration work with ECU d..
$79.74
Module Module Land Rover is a software package for diagnostics of cars Land Rover using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving v..
$62.46
The module supports the TCM/M32R CVT [512 KB/896kb/1024kb] CAN
Identification
Read/Write calibration
Read/Delete errors
Recalculation of the COP
..
$93.03
The module is designed to read or write full FLASH, or the field of calibrations ECU Bosch ME17.9.7 VAZ and UAZ diagnostic method without disassembling the ECU.
Please note:
Read the FLASH memory of the ECU, in the absence of the CAN bus in the car, remove the ECU and make connections..
$39.87
Module Module TOYOTA / LEXUS / SCION - software for diagnostic of TOYOTA / LEXUS / SCION with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
Module RENAULT / DACIA - a software package for diagnostics of cars RENAULT / DACIA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
License 69, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas + ECU programs).
Reading/VIN entry
This module allows you to work via the OBDII c..
$79.74
The module GEELY / LIFAN / BRILLIANCE - a software package for diagnostics of cars of brand of GEELY / LIFAN / BRILLIANCE with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
The module is intended for read-write FLASH memory of ECU Bosch EDC7UC31 of engines KAMAZ/MMZ/MTZ/JAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
The price shown is for the owners of the Sirius module 3x
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allo..
$26.58
Module DAEWOO / CHEVROLET - software for diagnostics car brand DAEWOO / CHEVROLET with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
License 91, may be applicable at the discretion of the licensee (user) to the operation of the Siemens ECU processors INFINION TRICORE and MOTOROLA MPC5xx installed on Hyundai/Kia vehicles performs the functions:
Identification of the ECU.
Reading / Clearing fault codes.
..
$79.74
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
$419.53
Module for HAFEI / XINKAI / ZX / BYD - a software package for diagnostics of cars HAFEI / XINKAI / ZX / BYD using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the ..
$62.46
Module GWM / CHANGHE / FDQD / SHUANGHUAN is a software package for diagnostics of cars, GWM / CHANGHE / FDQD / SHUANGHUAN using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fun..
$62.46
The module TAGAZ - a software package for diagnostics of cars TAGAZ using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle informa..
$62.46
The module is designed for reading and writing software and calibrations of the Delphi DCM 6.2V ECU of VAG group cars via UDP protocol via the diagnostic connector.
The module automatically corrects CS calibrations during recording.
The module supports the "Virtual r..
$132.89
The module is designed to build, edit and compare an extended error mask according to the OBD/SAE standard for SUBARU car firmware with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). The module allows you not only to turn off, but to turn back the DTC error code.
..
$39.87
The modules are designed for reading and writing the SIMOS12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECU installed on VAG vehicles.
Work with the SIMOS12.1/12.2 ECU is performed on the table without opening the ECU.
Работа с ЭБУ SIMOS16.11 is performed on the table with the ECU openin
..
$199.34
Allows you to work with Renault Clio/Megane/Scenic/Logan, equipped with systems Sirius32/EMS3132/Sirius34/EMS3134. ECU programming directly on the vehicle through the diagnostic connector. The main difference from similar applications is the ability to read/write programs for a replacement.
I..
$66.45
Module FAW / HAIMA / ZOTYE / CHANGAN - software for diagnostics car brand FAW / HAIMA / ZOTYE / CHANGAN with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the modul..
$62.46
The ISUZU module is a software package for diagnosing ISUZU vehicles using ScanDoc and ScanDoc Compact scanners.
The brand is opened in one click via the Internet. You do not need to re-download the ScanDoc program from the site and install it.
Module functions:
..
$62.46
Module is designed to work with the ECU of 2.0L Delphi DCM6.2A/DCM6.2C diesel engines installed on PSA group cars, working through a diagnostic connector. Supports reading, writing, checking and correcting checksums:
Citroen/Peugeot 2.0L HDi (DCM6.2A) [RD/WR/CK]
Citroen/Peugeot 2.0L..
$93.03
License 67, may be applicable at the discretion of the licensee (user) to the work:
Reading EEPROM 95320.
EEPROM Entry 95320
Reading Flash
Flash recording (with checksum recalculation)
Built-in immobilizer data editor CS, MAC, Login, Immo Status.
..
$93.03
Designed to read and record the calibration and program the ECU EMS3130 vehicle Renault Duster 1.6 L, via the diagnostic connector.
Extra features:
The calculation of the COP of field calibrations.
To change VIN: allows you to change the VIN code in the downloaded firmware.
..
$66.45
At the moment the module supports:
Reading
Entry
Identification
Verification and recalculation of the checksum (CS)
Read/erase error codes
It supports all installed in the Denso Mitsubishi processors 7058/7058S/7059
..
$93.03
The module allows you to view, edit and compare the "partial" DTC error mask, errors are available on the SCR system, NOx sensors, EGT sensors, FAN sensors, DPF differential pressure sensors, etc.
The automatic shutdown function of the SCR/AdBlue system is available.
Support fo..
$664.47
The car 'Lada Vesta/XRay/Largus' with electronic gas pedal, equipped with ECU M86/M74M.
The module is intended for read-write FLASH/EEPROM ECU М86 with a production of vases, based on the Infineon processor family XC27x5 via the built-in BootStrapLoader, and recording via the d..
$66.45
The modules are designed to read / write FLASH Chevrolet/Opel/Cadillac/SAAB, equipped with ECU Bosch ME9.x and the Bosch ME7.9.9 via the diagnostic connector.
Work with the J2534 adapter, sold separately. Module is a Bosch ME9.x GM makes automatic recalculation of the COP recorded calibration..
$53.16
The 88 Ford AdBlue module is designed to work with the AdBlue DCU17PC43 dosage ECU, installed on Ford cars paired with the SID212/SID212EVO engine ECU, via a diagnostic connector. Supports reading, writing, checking and correcting checksums.
AdBlue REDCM (DCU17PC43) [KV6A] [RD/WR/CK]
..
$66.45
Functionality you can see in the coverage map.
Module for BMW / MINI , a software package for diagnostics of BMW / MINI with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The fu..
$62.46
The module allows to make the chip tuning (reading and writing FLASH) ECU Bosch EDC17CV44/54 engines MMZ/MTZ/JAMZ/FAW/SHAANXI, mounted on trucks, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
The module performs automatic recalculation of the COP.
..
$66.45
The module is designed for reading and writing ECU MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90, installed on BMW cars.
Work with the ECU is performed on the table without opening the ECU. Identification and error reading/reset functions..
$199.34
The module allows read-write memory of the CPU of the ECU WestPort WP580 installed on the vehicles via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$132.89
The module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed in Chinese vehicles. The module allows you to: - Read and write the software and/or calibrations area (provided that the ECU itself allows reading the software area) - Calculate and, ..
$93.03
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the abi..
$79.74
Kia, Hyundai, equipped with ECU Bosch M(G)7.9.8. Designed for recording FLASH memory ECU Bosch M7.9.8 and MG7.9.8 via the diagnostic connector without removing the ECU from the vehicle.
..
$93.03
The module is designed to read / write calibration and program control UNIT Siemens SIM2K-243 GM vehicle Chevrolet Spark M-300.
The module allows reading and writing of programs or the field of calibrations, diagnostic method, without removing the ECU from the vehicle.
Works through the J..
$66.45
Kit modules:
Isuzu Transtron (J2534) Module is designed to read / write via the CAN-bus FLASH-memory Transtron ECU based on Renesas processors that are installed, in particular for cars with engines Isuzu 4JJ1, 4JK1, 4HK1, 6HK1 via the diagnostic connector.
Isuzu Transtron ..
$106.32
Allows you to edit and compare the error mask on a large number (about 1000) of Denso software. The module allows you not only to turn off, but to turn back the DTC error code.
Supported Software:
89663-01032- 89663-01121- 89663-02023- 89663-02161- 89663-02162- 89663..
$39.87
License 76, may be applicable at the discretion of the licensee (user) to the work:
Reading/Recording of the Flash memory of the ECU of the transmission of VAZ cars through the diagnostic connector or on the table (connection is available in the online help).
..
$66.45
The modules operate only in conjunction with the base module Delphi MT60/MT80 and designed for read-write full image of ECU Delphi MT60/MT80 diagnostic method using the J2534 interface.
..
$93.03
Module CHERY - a software package for diagnostics of cars of the brand CHERY with ScanDoc ScanDoc scanners and Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle..
$62.46
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$26.58
Cars Renault Logan 2, Sandero 2, Fluence, Megane 3, Latitude, Duster.. Designed to read and record the calibration and program the ECU mounted on Renault cars via diagnostic connector.
..
$66.45
Kia, Hyundai, equipped with ECU SIMK43/41, Chery QQ cars equipped with ECU SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface and CAN)
..
$79.74
Module SUBARU is a software package for diagnostics of SUBARU vehicles using scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
Receiving vehicle info..
$62.46
Module SSANG-YONG - a software package for diagnostics vehicles of the brand SSANG-YONG with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The module is designed for chip-tuning of cars Suzuli SX4 and Vitara (engine capacity 1.6 L), equipped with Bosch ME17.9.61.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use ..
$119.61
The SAE J2534 standard was introduced in 2002 to ensure the ability to reprogram the ECU via interfaces from different manufacturers. J2534 defines a standard interface to exchange data between the PC and the adapter. Because of this, the software manufacturer may, without delving into the specif..
$199.34
License 40, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of the calibration area (with recalculation of checksums)
..
$106.32
Kia, Hyundai, equipped with ECU Siemens SIMK43 and SIMK41, Chery QQ cars equipped with ECU Siemens SIMK31. Designed for read-write calibrations and program ECU Siemens SIMK31, SIMK41, SIMK43 via diagnostic socket (K-Line interface)
..
$53.16
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
License distribution after 31.10.2024!!! License 104 may be applicable at the discretion of the licensee (user) for working with ABS ECU on Tricore Aurix MCU (TC234-32F) installed on Lada Vesta NG, Lada Niva vehicles from 2024. Identification Reading/Clearing DTC Reading/Writing KM Reading/Writin..
$159.47
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
$239.73
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of ca..
$66.45
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
$119.87
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$66.45
Designed for read-write FLASH memory of ECU Cummins CM2150/2220/2880/2350 mounted on GAZ/MAZ/KAMAZ etc. via the diagnostic connector.
..
$199.34
The module is designed for reading/writing calibrations and programming the ECU EMS3140/3160/3161/SID321 installed in Renault/Nissan vehicles. Additional functions: - Calculation of checksum area of calibrations. - ECU identification. - Reading/resetting ECU errors. Attention! At the moment, ther..
$199.34
The empowerment of Ford modules work with the ECU SID208/SID209(CK4A), including full access to the FLASH EEPROM through the diagnostic connector.
..
$66.45
Module Siemens ACDelco intended read / write FLASH memory of ECU 5WY7128 fitted to cars Cadillac STS/SRX, via the diagnostic connector.
..
$39.87
The module is designed for chip-tuning VW Touareg 3.6 FSI engines CGRA CMTA and equipped with Bosch MED17.1.6.
Please note:
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only Co..
$132.89
Diagnostics of many different systems can be complex and time-consuming. The longer it takes to diagnose one car, the fewer cars will be inspected during the working day. Pyrometers speed up the diagnostic process. Point the pyrometer at the object, pull the trigger and read the temperature value..
$11.98
Daewoo Gentra (Delphi MT60), Chevrolet Aveo, Chevrolet Cruze (Delphi MT80), Chevrolet Cruze, Daewoo Lacetti (Siemens SIMTEC76). Designed for read-write FLASH memory of ECUS via diagnostic connector.
..
$66.45
Additional module for chip-tuning of cars VAZ and UAZ equipped with ECU M(E)17.9.7 and M(E)17.9.71 with electronic gas pedal and a manual throttle control.
The module allows for complete customization of the engine control ME17. Change all the most important calibration, including ..
$119.61
FIDs: 155, 157, 177
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.
Renault Siemens SID301 (FID:157)
This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0..
$239.73
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
$119.87
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
$239.73
License 61, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the Siemens Simtec 76 ECU in OBD II Mode and BenchMade mode.
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
..
$106.32
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
$78.40 $72.80
License 97, may be applicable at the discretion of the licensee (user) to work with ASM Delphi DCM Diesel installed on Ford vehicles, performs the following functions:
OBD II Mode (working on a car or on a bench):
Reading Identification
Reading Errors
Reset Erro..
$79.74
The modules are designed to read / write flash memory of ECU Visteon ESU-131/312/411/412/415/418 vehicle Ford Focus 2, C-Max, Kuga engines 1.8...2.0 l (2004...2010) and Ford Mondeo 4 S-Max, Galaxy with 2.0 engine...2.3 l (2004..2011 onwards)
..
$106.32
License 65, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading/Clearing fault codes.
Reading/Flash recording (calibration areas and ECU programs).
The module calculates the checksum of the calibration area.
&nb..
$93.03
This module enables the following additional functions:
Mixing of the calibration firmware Bosch ME17.9.7 VAZ and UAZ. The function requires the module ME17.9.7 VAZ/UAZ.
Patch to disallow read firmware Bosch ME17.9.7, Bosch ME17.9.71 (VAZ, UAZ), Bosch ME17.9.11/12 and ME17.9.21 (Kia..
$39.87
License 64, may be applicable at the discretion of the licensee (user) to the work:
Identification of the ECU.
Reading / Clearing fault codes.
Read processor FullFlash/Write calibration area.
The type of supported ECU installed by the MC:
GM ACDelco E37 ..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$93.03
License 126, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on SsangYong cars, which allows for full-fledged repair and restoration work with ECU data.
Functio..
$79.74
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
$359.60
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
$239.73
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
$239.73
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
$239.73
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
$239.73
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
$432.50
License 93, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS units installed on Jaguar / Land Rover cars,
which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
$359.60
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
$359.60
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.21, for example, the VW Golf 1.4 TSI, Skoda Octavia 1.2 TSI, Audi A3 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch М..
$159.47
License 13, may be applicable at the discretion of the licensee (user) to the work:
Reading/Clearing fault codes
Clearing collision information.
Unlocking the ECU.
Changing the ECU configuration.
Reading/VIN entry.
List of supported ECUs:
Renault SAND..
$79.74
The module is designed for chip-tuning of automobiles in China, equipped with Bosch ME17.8.8, for example, Chery Tiggo 2.0 L, Chery Bonus (A19), Lifan X60, Lifan Solano II, etc.
Please note:
Third-party module developer! Technical support from the author of the module (KHN0..
$132.89
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$132.89
The module is designed for chip-tuning VAG cars equipped with Bosch ME17.5.26, for example, Skoda Octavia 1.6 MPI, Skoda Rapid 1.6 MPI Skoda Yeti 1.6, 1.6 MPI VW Jetta, VW Polo 1.6.
Please note:
Third-party module developer! Technical support from the author of the module (..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.25, for example, the VW Golf 1.2 TSI, 1.4 TFSI, Skoda Octavia, Skoda Superb 1.4 TFSI, VW Jetta 1.4 TFSI.
Please note:
Third-party module developer! Technical support from the author of the module (K..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.5, for example, VW Touran 1.4 TFSI, VW Golf IV 1.4 TSI, VW Tiguan 1.4 TSI, Skoda Superb 1.4 TSI.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
..
$159.47
The module is designed for chip-tuning VAG cars equipped with Bosch MED17.5.2, for example, VW Passat 1.8 L.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the f..
$159.47
License 11, may be applicable at the discretion of the licensee (user) to the work:
Renault MeganIII/Scenic III/Fluence/ClioIII/Modus
Restores the eeprom Eur dump (EPS), makes it "new" - ready for installation on the car.
Identification of the ECU.
Read..
$106.32
License 82, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars Nissan / Infiniti, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 79, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with Takata SRS units based on SPC560P34L1 processors installed on Lada Vesta and UAZ Patriot cars, which allows for full-fledged repair and restoration wor..
$66.45
The module is designed to work through a diagnostic connector with a Delphi DCM7.1AP ECU installed on cars for the Indian market (Ashok Leyland, Eicher, Force Motors, Kia/Hyundai, Tata). It supports reading, writing, as well as checking and correcting CS.
Ashok Leyland TD (DCM2.5) [RD/WR/..
$132.89
Sending licenses after 31.10.2024!!!
License 100, may be applicable at the discretion of the licensee (user) to work with:
instrument panels on the MK Freescale 9S12HY64 installed on Lada Largus cars from 2024.
Identification
Read/Write KM
Read/Write c..
$79.74
License 71, may be applicable at the discretion of the licensee (user) to the work:
Via OBDII connector via CAN bus or KLINE with engine control units:
BOSCH M7.9.2/M7.9.7/M(G)7.9.8/ME17.9.11/ME17.9.11.1/ME(G)17.9.12/ME(G)17.9.13 based on ST10, C167, TC1762 processors installed..
$79.74
Module to work through the diagnostic connector for Ethernet control units Bosch MG1 and MD1 mounted on the BMW F and G-series.
Supported units Bosch processor-based NXP MPC5777 with 7.5 Mb of internal flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)
BMW Fx..
$419.53
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
$119.87
License 38, may be applicable at the discretion of the licensee (user) to the work:
Mazda 3 Color Display (93c86) 2018-... Reading/KM record
Mazda 6 Color Display (93c86) 2016-... Reading/KM record
Mazda 6 Color Display (93c86) 2017-... Reading/KM record
Mazda CX5 Color ..
$79.74
It is designed to read and write calibrations and programs of the EMS3180 ECU installed on Renault cars through the diagnostic connector.
Additional functions:
Calculation of the CS of the calibration area.
ECU identification: allows you to request the identification ..
$66.45
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
$299.66
The module is intended for recording and calibration of ECUS Bosch MEDC17 BMW series Exx via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45.
Bosch ME17.2.1/ME17.4.5, MEV17...
$132.89
License 42, may be applicable at the discretion of the licensee (user) to the work:
Dacia Logan RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Lada Largus FL RH850 Renesas R7F7010xx Reading/Erasing fault codes, Unlocking the ECU, E..
$79.74
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group according to UDS Protocol via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, ED..
$132.89
Module Functions:
Reading/Recording calibrations
Identification
Reading/Erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
Supported Models:
FOCUS (III SERIES) 2.0 16V TDCi (115 HP)
C-MAX (II) 2.0 16..
$66.45
The module allows you to display, edit and compare the error mask of the Kamaz car with the Bosch EDC7UC31 ECU.
Displaying error codes according to the standard OBD/SAE (P Code), SPN, Customer code, KTS code.
Error mask comparison mode with the ability to display values in the compared fi..
$39.87
The modules are designed to read and write the calibration and program the ECU mounted on Renault/Nissan diagnostic connector.
ECU Continental EMS3155 ustanavlivaetsya on engines 1.2 T.
ECU Continental SID310 is installed on the engines of 1.5 l and 2.3 L.
ECU Bosch EDC17C84 i..
$132.89
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
$167.81
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
$239.73
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$106.32
The module is intended for recording and calibration of ECUS Bosch MEDC17 cars of the VAG group over K-line or Protocol CANTP2.0 via the diagnostic connector.
The module supports the following types of ECUS:
Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP..
$132.89
Module features:
Reading calibrations
Recording calibrations
Reading the full data image
Recording a complete data image
Identification
Reading/erasing errors
Recalculation of the checksum
The module also supports:
..
$66.45
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
$419.53
Features of the module:
Write firmware
Read/Delete errors
Virtual reading
Check/Fix the checksum (the bypass digital signature)
Tabs:
CAN - for Master ECU
Slave To record a second engine ECU (Slave)
Stock - to return to the flow without using th..
$132.89
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$66.45
The module is designed for reading and writing software and calibrations of the Bosch EDC17 ECU of Suzuki cars via the diagnostic connector.
The module supports the following types of ECU:
Bosch ME17.9.5.
Bosch ME17.9.51.
Bosch ME17.9.6.
Bosch ME17.9.61 (r..
$106.32
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Recalculation of the checksum
Supported models:
FIESTA 7(VII) 1400 TDCI Power 68
FIESTA 7(VII) 1400 TDCI Power 68
GALAXY 2000 TDCI Power 13..
$39.87
Module FORD / LINCOLN / MAZDA - a software package for the diagnosis of car brands FORD / LINCOLN / MAZDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The function..
$62.46
FID: 180, 181
Module to read and write via the diagnostic connector Ford control units Bosch MG1.
Ford Bosch MG1CS015 TC277 (FID: 180)
The family support units Ford Bosch MG1CS015 processor-based Infineon Aurix TC277 with internal memory of 4 MB.
Allows readi..
$239.73
Identification
Read / Write Fullflash on the table
A record of calibrations for OBD
Read errors/ clear error
Recalculation of checksum
..
$106.32
The module for the new version of the program Chiploader NG
Module [50] UDS Bosch MEDC17 VAG - OBD2 is designed to record via OBD2 connector VAG group cars with ECU Bosch UDS.
Additionally supported:
Recalculation of the checksum field calibrations
Read..
$132.32
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
$299.66
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
The cars ECU:
Logan / Sandero EMS3120 TC1738 [2048k] CAN
Fluence / Megane EMS3120 TC1738 [2048k] CAN
Fl..
$86.38
License 72, may be applicable at the discretion of the licensee (user) to the work:
This module allows you to work via the OBDII connector on the CAN bus or K LINE with gasoline engine control units:
SIMK43, SIM2K-47 based on C167 processors installed on Hyundai, Kia concer..
$66.45
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
$299.66
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
License 103 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on the table with SRS Great Wall blocks based on the XC2336 MCU installed on Great Wall Haval vehicles, allowing for full repair and restoration work with this ECU data. Functions: Iden..
$79.74
The module is designed to work with the Bosch ECU automatic transmission 6HP, 8HP a / m JLR through the diagnostic connector of cars. Supported read, write, check checksum correction:
ZF 6HP26/6HP28 TCM (MPC5xx/TC1766) [RD/WR/CK]
ZF 6HP28 Continental TCM (TC1766) [AH42-Ax] [R..
$119.61
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$199.34
License 127, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS Continental units based on MK SPC560xxx installed on Suzuki cars, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 102, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or when directly connected via CAN bus with DCM2.5 control units of diesel engines installed on Ashok Leyland, Mahindra,Tata cars, which allows for full-fledged work with ECU data on chip..
$79.74
Attention! This module works in conjunction with CombiLoader 2.16 or later.
The module is designed for reading and writing software/calibrations of the AECS ECU installed on UAZ vehicles through the diagnostic connector.
The module automatically corrects CS calibrati..
$66.45
Supports full data image reading, full data image writing, identification, error reading/erasing, EEPROM reading/writing, checksum recalculation.
Allows you to clone Gen1 and Gen2 ACU.
..
$132.89
The module is designed for reading and writing SDI9 and SDI10 ECUs installed on Porsche cars.
Work with the ECU is performed on the table with the opening of the ECU. Identification and error reading/reset functions are also available.
The module automatically recalculates ..
$66.45
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
$179.80
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
$359.60
The module is designed to work with ECU Bosch ME(D)17/EDC17 working on CAN Protocol TP2.0/K-Line. Supports recording via the diagnostic connector modified firmware, validation and correction checksums. Supported ECU MED17.1/17.1.1, ME(D)17.5/17.5.1/17.5.2/17.5.5/17.5.6/17.5.20, EDC17U01/U05, EDC1..
$119.61
Module features:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Recalculation of the checksum
Supports reading Full Flash and recording calibrations, Subaru gasoline cars, ECU manufactured by Hitachi/Unisia Jecs with ..
$119.61
Designed for chip-tuning of cars mounted ECU M12/M75/M74.5. Supported read and write via the diagnostic connector
..
$66.45
Module kit:
The module is designed to read/write FLASH memory of DSI TCM ECUs installed on SsangYong/Geely vehicles via the diagnostic connector. The module performs automatic correction of the COP of calibrations during recording.
The module is designed to write software / calibrat..
$93.03
Designed for chip-tuning of cars mounted ECU M12 / M75 / M74.5. Supported read and write via the diagnostic connector
..
$106.32
The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector.
Module is the automatic correction of the COP calibration during the recording.
Work with the J2534 adapter, sold separately.
..
$66.45
The module is intended for read-write FLASH memory of ECU AMT VAZ via the diagnostic connector.
Module is the automatic correction of the COP calibration during the recording.
Work with the J2534 adapter, sold separately.
..
$66.45
Module Functions:
Recording calibrations
Reading the full data image
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports only recording and converting stock firmware from the IDS database (VCM) to bina..
$66.45
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Module AUDI / VW / SEAT / SKODA - a software package for the diagnosis of car brands AUDI / VW / SEAT / SKODA vehicles with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
..
$62.46
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
$239.73
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
..
$19.93
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
..
$66.45
The module allows you to produce professional chip tuning of cars VAZ with electronic gas pedal (EGAS), equipped with the latest ECU M74. Also supports editing firmware ECM M74K (VAZ 'Classic', without an electronic gas pedal). Edited over 380 calibrations of the control system M74: starting mode..
$106.32
License 99, may be applicable at the discretion of the licensee (user) to the work:
1. OBDII Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculation of checksums)
..
$106.32
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
$239.73
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
$239.73
This module is designed to read and write FLASH memory of ECU Keihin CPU SH7058 / SH72543 / MPC installed on Honda cars via diagnostic connector OBDII At the moment the module supports ECU Honda Accord (8th generation), Honda Civic (8, 9th generation), Honda Jazz/Fit (2nd generation), Honda C..
$189.63
Includes extra features: preparing firmware ME17.9.11/12/13 to record its diagnostic method (WITHOUT opening the UNIT) disable diagnostic read firmware ME17.9.11/12/13 ( just 17.9.7, 17.9.71, 17.9.8, 17.9.21). Advanced features available for purchase under any of the modules of the family Bosch M..
$26.58
The loader allows you to read and write firmware in flash memory controllers installed on Russian and foreign cars. The convenience of operation, reliability, availability of a large number of additional functions, constant updates and technical support make our loader the best choice for profess..
$199.34
Supports reading Full Flash and recording of calibrations petrol cars Suzuki, ECU manufactured by Hitachi c CPU SH7058. Recalculation of the CRC. Read & clear error ECU internal combustion engine.
Suzuki Escudo 2.7 L Suzuki Grand Vitara 2.7 L
..
$66.45
Specified value of the usb protection key of the program. The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
Openbox 3.3 - the program loader, ..
$33.22
This module allows you to work on the car via the OBDII connector with the Visteon ECU installed on Ford cars.
Module Functions:
Identification Reading
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalculation of calibration area c..
$66.45
License 94, may be applicable at the discretion of the licensee (user) to work with ECM / TCM Continental installed on Ford vehicles, performs the following functions:
OBDII Mode (work on car or table):
Reading Identification
Reading Errors
Reset Erro..
$93.03
License 90, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
This module allows you to work on a car via an OBDII connector with Siemens ECM installed on Ford cars.
OBD II Mode (working on a car or on a desk):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Flash recording with recalcula..
$66.45
License 74, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (without recalculatio..
$106.32
Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be writt..
$139.54
License 77, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode(Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading Flash
Recording of calibration area (..
$106.32
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$265.79
The module supports the functions:
Identification
Reading calibration / calibration Record
Read errors/ clear error
Recalculation of checksum
Virtual read server latest update Ford
The conversion vbf
Vehicle Brand Model Version Engine Software
type ..
$39.87
Set of modules (General license):
Continental DC4 TCM
Continental TA2005 TCM
The modules are designed to read / write calibrations and programs of the DC4/TA2005 TCM ECU installed on Renault vehicles via the diagnostic connector.
Additional function:
Cal..
$66.45
Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to v..
$51.83
The module is designed to work in service mode "on the table" with the ECU of the VAG AQ250 (09G)/A L 750 (09D)/AL1000 (0C8), Volvo/LR/Ford AWF21, Mini GA6F21WA, Mazda AW6A-EL, VAG AQ250 (09G), AL1000 (0C8), PSA AM6-3, Isuzu AWR6B45-2, Mitsubishi V8AWG, Toyota/Lexus AE80F, Volvo AWF8F35, BMW..
$199.34
The module is designed for diagnostics of the WISE15 ECU (WEICHAI)
..
$106.32
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
$167.81
Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries ..
$79.74
Modules allow you to produce a chip tuning (reading and writing FLASH) ECU Delphi MT34, Delphi MT80 and Delphi MT92 vehicle Great Wall/Haval/Geely, via the diagnostic connector.
Work with the J2534 adapter, sold separately.
..
$106.32
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are:
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
ME17.9.11/12, Hyundai, K..
$199.34
The module is designed for reading and writing FLASH and EEPROM of the control UNIT, based on processors of Infineon TriCore family, via the built-in BootStrapLoader.
To this type are (read/write/unlock):
ME17.9.7, VAZ, UAZ
M(E)17.9.71, TPROT 12, UAZ (new!)
Read..
$93.03
Distribution of activation files after 11/30/2022
License 98, may be applicable at the discretion of the licensee (user) to the work:
1. OBD II Mode (Car operation):
Reading Identification
Reading Errors
Reset Errors
Reading..
$106.32
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
$299.66
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$247.15
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
$419.53
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
$299.66
License 111, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS based on MK SPC56xx/Renesas H8Sx 1725 installed on Acura, Honda cars, which allows for full-fledged repair and restoration work with ECU data.
Functi..
$79.74
Read/Write firmware
Read/Delete errors
Check/Fix the checksum
The module automatically determines the size. Supports all markets. Read a full Hour, recording 10-15 minutes of cars and trucks. Machinery is the ECU is written HOUR SH7059 processor.
Used processors SH7058, ..
$106.32
Module ACURA / HONDA is a software package for the diagnosis of car brands ACURA / HONDA with the help of scanners and ScanDoc ScanDoc Compact.
Brand opens in one click via the Internet. Re-download the program ScanDoc from the website and install it no need.
The functions of the module
..
$62.46
The extension for the program OpenDiagPro intended for automotive computer diagnostics systems injection cars Renaut.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after order.
..
$11.96
The module is designed for chip tuning of VAG cars equipped with Bosch MED17.5.20 with 1.4 TFSI engines.
Pay attention:
A third-party developer module! Technical support from the author of the module (KHN09).
Firmware of Bosch ME17 family controllers are saved in..
$159.47
Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
$744.21 $543.54
The extension for the program OpenDiagPro is designed for computer diagnostics automotive fuel injection systems of cars of mark Hyundai.
The module works as part of a program OpenDiagPro, and independent functioning impossible. The module activation in the activation file sent by email after..
$13.29
The module is designed for recording and reading (read-only ECU Avtel M73) FLASH memory of the ECU family January-7.2+/M73 via diagnostic connector OBDII
At the moment not supported the ECU Avtel M73 with identifiers ending in DB04, and having such protection algorithms.
..
$11.71
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
$239.73
Module functions:
Recording calibrations
Identification
Reading/erasing errors
Read/Write configuration data
Virtual reading
Recalculation of the checksum
DDE721b
DDE73a
DDE731a
MEVD17.2
..
$132.89
License 120, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with Bosch SRS units based on MK + EEPROM 95080 / 95128 / 95160 / 95320 / 95640 installed on cars: Ford, Mazda, LandRover, Hyundai, Kia, MB, Dodge, Mitsubishi, Nissan, Volvo..
$132.89
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
$247.15
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
$479.46
Read/Write firmware
Read/Delete errors
Check/Fix the checksum (the bypass digital signature)
Virtual reading/Converting from dealer format (*.VBF)
..
$66.45
It works with SiriusD3/D32/4R/42R/D42/D 52 ECU units that can be installed on GM vehicles.
The module has two tabs for working with ECU data and allows you to perform the following functions:
Tab OBDII mode (operation via the diagnostic connector), for professional Chip tuning:..
$106.32
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
$239.73
The module is designed for diagnostics of EDC17CV44/54 CAN
..
$106.32
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
$299.66
Reading(slow)/Entry of the calibration Can
Read/Delete errors
Check/Fix the checksum
Virtual reading
Supported units EDC17C08 and EDC17CP14 with any TPROT
..
$66.45
The module is designed to work with blocks of EMS EMS S7 and S8 that are installed in trucks from Scania. Supported read, write 'follow', replacement, inspection and adjustment of the COP, both with a direct connection to the unit (on the 'table') and via a coordinator (on the 'table' and in the ..
$398.68
Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any e..
$86.38
The module is designed for chip tuning of Citroen and Peugeot cars with 5GY (EP6FDTM), 5GZ (EP6FDT) engines equipped with Bosch MED17.4.4, for example, Peugeot 208 A9, Peugeot 308 T9, Peugeot 3008 T8, Citroen DS3 A55, Citroen DS5 B81, Citroen C4 Grand Picasso B78.
Pay attention:
..
$159.47
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
$419.53
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Container File. To download these firmware you need to use loader only CombiLoader.
Saving in the us..
$159.47
Designed to work with Hitachi ECU (read full flash, write calibration, recalculation of the COP) with the SH705x CPUs installed on Nissan/Infiniti.
read Full cpu dump SH705x, SH7253x / Read Full Flash cpu SH705x, SH7253x
recalculation of the checksum / CRC
..
$159.47
The module allows you to view, compare and edit the firmware files of GAZ cars, a GROOVE with a YAMZ 53xx engine, an EDC17CV44/54 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error m..
$132.89
Read/Write calibration by K line
Record calibration + program Can
Read/Delete errors
Check/Fix the checksum (fake digital signatures)
Supported units EDC16C39-5.41 and EDC16CP34-5.30
..
$66.45
The module allows you to view, compare and edit the firmware files of MAN c ECU EDC17CV42 cars.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, sensor calibration, DTC error mask are available for editing. The modu..
$664.47
License 41, may be applicable at the discretion of the licensee (user) to the work:
The module allows you to work with the ACDelco E83 ECU in OBD II Mode, Bench Mode and Recovery mode.
1. OBDII Mode(Car operation):
Reading Identification
Reading Er..
$106.32
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation: Mazda3/CX5/6 1.5, 2.0, 2.5 L SKYACTIV-G Z6 1.6 L
Car Mazda CX-5 I 2.5L Skyactiv-G PYCVEC000PY0B061 192 DENSO SH72543 PYCV-188K2-C OBD 48
Car Mazda 3 BM 2.0L Skyactiv-G PEJJEC..
$66.45
License 25, may be applicable at the discretion of the licensee (user) to the work:
Through the OBDII connector or on a table with SRS units installed on Hyundai/Kia cars, which allows for full-fledged repair and restoration work with ECU data.
ECU for IN..
$132.89
The kit contains modules:
Module SID206 designed for recording and(or) field calibration of the ECU SID206 vehicle 4 Ford Mondeo, Galaxy, S-Max, Kuga 1 with engines of 1.8—2.0 L.
Module SID208 designed for recording and(or) field calibration of the ECU SID208, installable in particu..
$66.45
Module for the new version of the Chiploader NG program
Module [52] Delphi MT38 - OBD2 - Boot is designed to work with MT38 ECUs installed on Kia / Hyundai cars. Supported reading, writing, cloning, checksum control / correction, disable immo.
..
$61.61
The module is designed for chip tuning of Chevrolet Epica cars with 2.0L and 2.5L engines equipped with Siemens SIM2K-D160 ECU (5WY1B12G, 5WY1B18E, 5WY1B23E, 5WY1B41B, 5WY1B41D, 5WY1B41E, 5WY1B41F, 5WY1B42E, 5WY1B43E, 5WY1B46E, 5WY1B46F , 5WY1B60B, 5WY1B60C, 5WY1B60D, 5WY1B63D, 5WY1B63E, 5WY1B65A..
$132.89
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
$239.73
Multibrand scanner DS150 Bluetooth 2015.3 includes all the functionality of the popular scanner CDP and fully covers all system of cars sold on the European market.
Can be used with software 2013.3 - 2015.3, Wurth WOW etc.
DS150 Bluetooth support full diagnosis of vehicles Mercedes-Benz,..
$81.73 $73.09
For owners module M75
Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To ..
$46.51
The Ford EDC17CV41 module 24 allows you to view, compare and edit firmware files of Ford Cargo F-Max vehicles (Bosch EDC17CV41 ECU).
Calibrations are available for editing: boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phases, torque limits, ..
$398.68
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
$239.73
The module supports: identification, read FULL flash, write field calibrations, the reading and deletion of errors, checking and correcting the checksum. Supported ECU's Continental SIM2K 140/141/241/341.
..
$79.74
The module is designed to record the FLASH memory of the ECU M 7.9.8 7.9.8 and MG via OBDII diagnostic connector.
..
$70.31
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$53.16
Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. ..
$106.32
Module Functions:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Read/write configuration data
Recalculation of the checksum
..
$79.74
The module is designed to read, write, FLASH memory of various types of ECU Siemens via OBDII diagnostic connector.
..
$82.02
Designed for chip-tuning GAS with the installed ECU M12.3. Supported read and write FLASH via diagnostic connector
..
$66.45
Designed for chip-tuning of cars VAZ, UAZ with mounted ECU BOSCH ME17.9.7. Supports only FLASH programming through the diagnostic connector
..
$106.32
Module with support Sirius D3/D4/D32/D42/D52 (Chevrolet Aveo, Lacetti, Spark, Daewoo Matiz) is designed to read and write FLASH memory from ECU Sirius via OBDII diagnostic connector.
..
$35.12
The module is designed to work with the engine control units (ECUs) produced by Continental for SGMW and Geely cars. For SIM2K-D51/51.4/SCE60, reading and writing through the diagnostic connector is supported, while for Easy U2/U2.5/U2W/U3.6, connection "on the bench" may be required. Checksum ve..
$93.03
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
$239.73
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
$599.33
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
$239.73
License 81, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with SRS units based on TriCore Auris Tc2x processors installed on cars
Hyundai/Kia, which allows for full-fledged repair and restorati..
$79.74
Additional module for chip tuning Peugeot with the control units Bosch MEVD17.4.2.
Please note:
Third-party module developer! Technical support from the author of the module (KHN09).
Firmware families Bosch МЕ17 are stored by default in the format of SMS-Soft Containe..
$132.89
The module is designed to work with the AECS-FC34/50/51 and LinControl LEC4AF/4AP ECUs installed in vehicles produced in China with gasoline engines. It supports reading, writing, checking, and correcting checksums (if available). The work is carried out both through the diagnostic connector and ..
$119.61
The module allows you to edit the firmware of SUBARU cars (2.0 engines) with the Denso MCU SH7055/SH7058 control unit (file size 512Kb and 1Mb). Tables of UOZ, mixture composition, throttle position, torque request, error mask, etc. are available.
Supported Software:
E2UD00..
$39.87
License 73, may be applicable at the discretion of the licensee (user) to the work:
Via the OBDII connector or on a table with gasoline engine control units:
MIKAS 12(GAZ) by KLINE
ITELMA M74.5(VAZ) by KLINE
ITELMA M75(VAZ) by KLINE
ITELMA M86(VAZ) by CAN
..
$66.45
Reading calibrations
Recording calibrations
Reading/erasing errors
Recalculation of CS
..
$106.32
Reading calibrations
Recording calibrations
Reading/erasing errors
Recalculation of CS
..
$93.03
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
$239.73
License 08, may be applicable at the discretion of the licensee (user) to the work:
The work is done by upgrading the Flash file.
Works as an editor.
DENSO engine control units on NEC 76F00xx processors with firmware size are supported 256, 320, 368, 384, 496, 736, 992, 1024.
..
$79.74
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
$239.73
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
$359.60
License 106 may be applicable at the discretion of the licensee (user) to work with DENSO instrument panels on Spansion S6J3001 ECUs installed in Toyota, Lexus vehicles from 2018. Work is carried out with open and closed ECUs, via the CAN bus through the diagnostic connector or on the bench, by d..
$199.34
License 143, may be applicable at the discretion of the licensee (user) to the work:
with instrument panels on the MK Artery Cortex M4 (AT32F403) installed on Lada Granta and Lada Niva cars from 2024.
Identification
Reading/Clearing the DTC
Reading/KM Record
..
$79.74
RC Read calibrations
WC Recording calibrations
ID Identification
ER Read/Erase Errors
..
$66.45
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
$359.60
Supports only the following Honda/Acura:
Accord7/TSX 03'-07' ECU 7055 [512]Matsushita K 37805-RBA-Xxxx; 37805-RBB-Xxxx
Accord7 05'-07' ECU 7058[1024]K Keihin 37805-RAD-Xxxx
2006 TSX ECU 7058[1024]Matsushita K 37805-RBA-Xxxx
Legend/CR-V 02'-07' ECU 7058[1024]K Keihin 3780..
$93.03
The module supports virtual reading and writing of calibrations, reading and deleting errors, checksum recalculation.
..
$93.03
License 134, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or by direct connection via CAN bus with ITELMA M74.8/M74.9 control units on MK STM SPC58VQ and Artery AT32F4xx series gasoline engines installed on VAZ cars, which allows for full-fledge..
$132.89
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
$359.60
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
$299.66
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
$239.73
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
$239.73
Module supported:
Virtual reading
A record of calibrations
Read/Delete errors
Check/Recalculation of checksum
Bypass the digital signature
Supported ECU's:
ME(D)17.1/17.5/17.1.1/17.1.6/17.5.5/17.5.20/17.5.21/17.5.22/17.5.24/17.5.25/17.5.26/
EDC1..
$212.63
Module Features:
Reading calibrations
Recording calibrations
Identification
Reading/erasing errors
Virtual Reading
Recalculation of the checksum
The module supports the read/write and the conversion stock firmware with base IDS (VBF) in binary form.
..
$66.45
License 105 may be applicable at the discretion of the licensee (user) for work: through the OBDII connector or on a table with SRS Volvo blocks based on the TMS570 MCU installed on Volvo vehicles, allowing for full repair and restoration work with the ECU data.
Functions:
Identificat..
$79.74
A record of calibrations
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
The module works in mode 'on the table' and OBD2. The cost of the module can be changed later.
List of cars:
Car Isuzu D-MAX RG01 3.0 L L4 4..
$492.48
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
$479.46
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
$299.66
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
$239.73
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
$239.73
The GAZ Cummins CM22xx module allows you to view, edit, compare the firmware files of GAZ cars with the Cummins ISF2.8, ISF3.8 engine with the Continental CM2220 control unit.
The module differs from the "Lite" concept and contains more than 2000 basic calibrations. Available calibrations for..
$199.34
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
$299.66
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
$119.87
The program works only with usb key, the same for all modules. Key without modules is not for sale.
Modules activation in the presence of the usb key 1-24 hours in business days (usually 1-2 hours).
PCMflash - loader with the ability to record a stock and aftermarket firmware via the vehicl..
$35.88
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
$239.73
Designed for chip-tuning of cars and cars of Chinese production installed ECU BOSCH M7.8. Supports recording FLASH via the diagnostic connector. As well as reading and writing FLASH/EEPROM memory controller via BSL mode.
..
$66.45
The module allows you to view, edit, compare the firmware files of Foton, JAC cars with Cummins engine with the Continental CM2880 control unit.
It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader.
The module contains more than 1000 b..
$332.24
You can edit full feature set supported by the engine control unit or ETACS. Staff may remove the immobilizer. The feature set depends on car, year, market and model.
The module supports the functions:
Identification
Reading/erasing fault
Read/write configuration data
..
$79.74
The Kamaz Cummins CM2xxx 4.5-6.7 module allows you to view, edit, compare the firmware files of Kamaz vehicles with a Cummins engine of 4.5 and 6.7 with a Continental CM2150, CM2200, CM2880 control unit
The module contains more than 2000 basic calibrations. Available calibrations for torque, ..
$199.34
The module allows you to view, edit, compare the firmware files of Kamaz, JAC, Foton cars with a Cummins 3.8L engine with a Continental CM2220 control unit. It is possible to open and edit firmware files ONLY in the * format.bin, read using Combiloader. The module contains more than 1000..
$398.68
The KMS MD1CE100 module allows you to view, compare and edit the firmware files of Kamaz K5 cars with an R6 engine (Bosch MD1CE100 ECU).
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection phase, request and torque limit, DPF, EGR, AdBlue, ..
$664.47
The Kamaz Cummins CM2xxx 8.9 module allows you to view, edit, and compare the firmware files of Kamaz vehicles with Cummins engine volume 8.9 with the Continental CM2880 control unit.
The module contains more than 2000 basic calibrations. Available calibrations for torque, injection quantity,..
$199.34
The module is intended for cloning on the table, without parsing the ECU. Supported and filled in TCU in a metal case and not filled in a plastic housing.
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
..
$132.89
The China EDC17CV44 Truck module allows you to view, compare and edit firmware files of FAV cars, Shacman trucks, MAZ, Yutong, etc. with a WP7, KR10, WP12 engine with an EDC17CV44 ECU.
Calibrations of boost pressure, fuel pressure, fuel supply, fuel supply correction, injection pha..
$332.24
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$53.16
Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot ..
$106.32
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 8..
$66.45
The module is designed ECU reprogramming IEFI6/ITMS-6F Daewoo cars via diagnostic connector GM-12
..
$41.05
Переходник для Mercedes. Используется для соединения с авто Mercedes у которых 38-контактный круглый диагностический разъем.
Работает с устройствами у которых на выходе OBD-II разъём.
..
$3.36
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
$299.66
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
$239.73
For owners module M74 6.38
Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works ..
$46.51
The module is designed to read and write FLASH memory from ECU ME7.9.9 Chevrolet Captiva via OBDII diagnostic connector.
..
$58.61
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
$239.73
Supports reading and writing of the gasoline auto. Mazda with volumes 2.0, 2.5, 2.3 T - CX7,3,6 2010+
..
$93.03
The module is designed to work on diagnosticheskogo the OBD2 port. To read a complete image of the Flash memory are written only calibration.
..
$93.03
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
$239.73
Instead of a main cable + adapter OBDII-16
..
$23.92
The module supports:
reading Full Flash 23 minutes
recording calibrations 45 minutes (10000-70000)
checksum recalculation
identification
reading/erasing errors
..
$93.03
VW Touran, Golf, Passat, Transporter, Caddy cars with engines AVQ,BKC,BMT,BLS, etc. with a volume of 1.9L
Supported Software:
1037367485P379U6FP
1037368205P213U6FT
1037370254P213U8C3
1037370811379U85B6
1037371094379U85B6
1037371250379U85B6
..
$39.87
License 43, may be applicable at the discretion of the licensee (user) to the work:
Renault Kadjar Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Megane I V Reading/Erasing fault codes, Unlocking the ECU, Erasing collision data
Renault Espace..
$79.74
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader).
The possibility of opening a firmware in BIN format (normal binary).
Automatic checksu..
$106.32
Additional module for chip tuning Chevrolet Spark M300 engine 1.25 L, ECU Continental (Siemens) SIM2K-243.
Supported versions:
906FX2F2
906FX4F2
Features of the module:
The possibility of opening the flash SMS-Soft Container File (new format for ChipTuningPRO and C..
$132.89
License 130, can be applied at the discretion of the licensee (user) to work:
through the OBD II connector with SRS units based on the Tricore Aurix TC2xx MK installed on Hyundai/Kia vehicles, which allows for full-fledged repair and restoration work with ECU data.
Functions:
..
$79.74
License 129, can be applied at the discretion of the licensee (user) to work:
through the OBDII connector or on a table with SRS TRW units based on the Tricore Auris TC234L-32F MK installed on Toyota vehicles, which allows for full-fledged repair and restoration work with ECU data.
..
$79.74
License 128, may be applicable at the discretion of the licensee (user) to the work:
through the OBDII connector or on a table with SRS Continental units based on the Renesas RH850 R7F701009 MK installed on Chery cars, which allows for full-fledged repair and restoration work with ..
$79.74
ECU M86 applies to cars Lada Vesta and X-Ray. The M86 project is a further development of motor control M74/M75. The manufacturer of the ECU — NPP ITELMA. By analogy with the systems of the previous generation M74 and M75, the new project will apply two different types of software FOR the product..
$106.32
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for f..
$79.74
Module for motor vehicles GAS, SHAANXI, FAW with the control units EDC17CV44/54 using Mscan EDS-24.
..
$66.45
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
Virtual reading (one button, the program downloads the Ford servers need VBF)
Conversion of VBF to BIN
BSL
Reading firmware
Read the password in OBD mode
Unlock in BSL for..
$66.45
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)
Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Mar..
$239.73
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
List of cars:
Car Nissan Qashqai 1.6 TDCI R9MMT2WD 23710-4EB2H Bosch TC1782 EDC17C84 OBD 80
Car Nissan Note E12 1.2 L HR12DE e-Power I3 + e..
$132.89
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
$239.73
Reading calibrations
A record of calibrations
The writing of a complete image data
Identification
Reading/erasing fault
Virtual reading
Recalculation of checksum
MED17 only a virtual reading. When tuning record-only calibrations. Stoke can record and ..
$132.89
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
..
$66.45
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
..
$66.45
The module allows you to view, edit, and compare the firmware files of MAN cars with the Bosch MD1CE100 control unit. It is possible to open and edit and compare firmware files ONLY in the * format.bin. Contains more than 200 basic calibrations. Available calibrations of torque limitatio..
$664.47
Reading calibrations
A record of calibrations
Identification
Reading/erasing fault
Recalculation of checksum
..
$186.05
Supported ECU's MAGNETI MARELLI 7GV / 7GVE / 4HV
Read/Write firmware
Reading/Erasing fault
Check/Recalculation of checksum
Soon will be added Simos 7.1/ 7PP/ 7.1 A
..
$79.74
The module supports the functions:
Identification
A record of calibrations
Reading/erasing fault
Virtual reading
Recalculation of checksum
..
$132.89
The module supports the identification, reading and writing of calibration, reading and deleting faults, checksum recalculation.
..
$46.51
Module supported:
A record of calibrations
Reading full image data
The writing of a complete image data
Identification
Reading/erasing fault
Read/write EEPROM
Recalculation of checksum
..
$66.45
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation
..
$39.87
The module supports reading and writing of calibration, reading and deleting faults, checksum recalculation.
..
$79.74
![[53] MERCEDES DELPHI CRD - OBD2](https://en.ecupro.kz/image/cache/data/products/chipldr_ng-150x150.jpg "[53] MERCEDES DELPHI CRD - OBD2")
