Professional multi-brand car scanner Scanmatik 3 is designed for diagnosing electronic control systems of modern cars. It works with a personal computer, tablet, or smartphone, with programs for Windows and Android included. When the driver is installed (included in the package), it works with th..
Module for the calibration firmware and atmospheric turbocharged snowmobiles Arctic cat with power management Denso 32920-49Xxx processor-based Renesas SH7052.
..
FIDs: 335, 336
A module for working on a table via the CAN bus with Continental control units for BMW petrol cars.
BMW Continental MSD8X TC1796 BENCH-CAN (FID:335)
The units are powered by an Infineon Tricore TC1796 processor with 2MB internal flash memory.
The fa..
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
Module to work through the diagnostic connector for Ethernet control units Bosch installed on diesel cars BMW F-series. Does not require the removal, opening or drilling unit!
Attention! This module does not work using J2534 adapters, requires Cable ENET-to-OBD2. The module ONLY w..
Module to work through the diagnostic connector for Ethernet control units Bosch MG1 and MD1 mounted on the BMW F and G-series.
Supported units Bosch processor-based NXP MPC5777 with 7.5 Mb of internal flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)
BMW Fx..
Module to read and write via the diagnostic connector control unit transmission GS20 Siemens and Bosch GS8.60.2, installed on the BMW cars.
Bosch GS8.60.2
This type of ECU is installed on the BMW cars equipped with the boxes of automatic models ZF 5HP24. Supported read full memory full flas..
Module to calibrate the firmware of the control units Bosch EDC17CP02 BMW diesel cars.
Supported file size is 1.46 MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
..
Module to calibrate the firmware of the control units Bosch EDC17CP09 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
Module to calibrate the firmware of the control units Bosch EDC17CP45 diesel BMW cars.
Supported file size 4MB.
Available the following cards:
Airmass: airmass flow desired with enabled and disabled EGR, maximal airmass flow, airmass correction
Boo..
Module for editing of calibrations motorcycles KTM and Polaris with the control units Bosch M17.8.7 and ME17.9.74.
Available the following cards:
The calculation of the air mass and load calculation of air passing through the throttle,ratio of enrichment/depletion during accele..
Module to calibrate the firmware of the control units Bosch MD1 diesel BMW cars. Supports all the necessary maps for tuning, disable the EGR, DPF, and SCR (ADBlue)!
Supported file size 7.5 MB.
A list of available maps:
Control air mass: expected mass air flow..
Module to calibrate the firmware of the control units Bosch ME(D)(G)17.9.8 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and the turbine, I..
Module to calibrate the firmware of the control units Bosch ME(G)17.9.11/12/13 atmospheric gasoline cars Kia/Hyundai.
Available the following cards:
Calculation of the mass of air: mass flow rate through the throttle, the calculated filling, maximum flow rate through the thrott..
Module to calibrate the firmware of the control units Bosch ME(G)17.9.21/22 and ME17.9.2 atmospheric gasoline cars Kia/Hyundai.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Correction according to the temperature of the EXHAUST gas: the C..
Module for the calibration firmware turbo and atmospheric vehicles BRP Can-Am, Ski-Doo, Sea-Doo, Spyder with the control units Bosch ME17.8.5.
You can edit the following cards:
calculation of the mass of air and mass flow through the throttle
momentum XX
enrichment and obe..
Module to calibrate the firmware of the control units Bosch ME17.8.8 and Bosch ME17.8.8.1 petrol atmospheric and turbocharged cars of Chinese production.
Supports the following cards:
Control the mass of air: mass flow rate through the throttle, the throttle position..
Software module for editing calibrations Bosch MED17.8.10 ECUs of petrol vehicles from China market.
Supported maps:
Air Control: Airmass flow through throttle valve base, Boost pressure limitation by intake temperature, Throttle valve position from accelerator pedal..
FID: 282
Universal module for Bench reading and writing for Bosch MG1/MD1 ECUs based on SPC and Aurix MCUs.
Attention! Module works only with Scanmatik SM2 or SM2 Pro. Also it needs to connect ECU on the bench with any adapter with automatic power management (SM2 ben..
Module to calibrate the firmware of the control units Bosch MSE 3.0, used in various types of motorcycles.
You can edit the following cards:
Idle speed: the Rpm of the twentieth
Start: Phase-injection at start-up, Phase of the injection according to the engine speed, the correct..
Software module for editing calibrations of Bosch MSE6.0/US6.0 ECUs
Available maps:
Air control: Pulsation correction for mass air flow in additional mode
Airmass calculation: Airmass flow through throttle valve, Manifold absolute pressure in case of sensor error,..
Module for calibration of firmware of Bosch ME control units(D)17.8.10, used in CFMoto motor vehicles.
The following calibrations are available for editing:
Air Control: Accelerator pedal map
Boost limiters: Boost limitation by coolant temperature, Boost limitatio..
FID: 6, 78, 79
The module is designed to work through the diagnostic connector with the motor equipment of Chinese production with the control units Bosch MSE3.0 and US6.0. Allows to identify versions of the software in blocks, virtual reading from the server and write fiel..
Module to read and write flash memory of engine control units Bosch gasoline cars in China.
The Bosch ME7.9.7 (FID: 68)
Control unit Bosch ME7.9.7 is based on the C167 CPU with external flash memory 1Mb. Supported virtual reading and writing, as well as correction of the COP .
..
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86, 146, 158
Module to read and write flash memory of engine control units Delphi gasoline cars in China.
Delphi MT20U (FID: 51)
The control unit MT20U Delphi is based on the processor Motorola MC912DT128 with i..
Module to read and write flash memory of engine control units of diesel cars in China.
China Delphi DCM3.7AP (FID: 145)
The control unit is powered by a processor Renesas SH72513 with internal flash memory of 2.0 Mb. Allows reading and writing to the CAN bus via the diagnostic conne..
FID: 83
Module for reading and writing the flash memory control units Siemens/Continental petrol cars in China.
Continental Simos 9.5 (FID: 83)
The control unit Simos 9.5 is based on the C167 CPU with external flash memory 512 KB. Supported virtual rea..
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units Continental GPEC (SIM90) processor-based Motorola MPC561 external FLASH memory 2Mb.
The following calibration: Volumetric efficiency, mass flow through an orifice the mass flow limiters,..
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep and Fiat control units for Continental GPEC2 on the basis of the MPC5566 processor with an internal flash memory of 3Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calcul..
Module for the calibration firmware different motorcycles BRP, Ducati, Arctic Cat, Stels, Dinli, etc. with the control units Continental M3C.
Available the following cards:
The calculated mass air flow to throttle position, correction of the estimated air flow correction volume..
FIDs: 191, 192, 193, 194, 195, 196
Module to work via the diagnostic connector on the table with the control units Continental M3C.
Allows identification of the software version, read and write the fullflash to the CAN bus, examination and counting of the KS region o..
Module to calibrate the firmware of the control units Continental SIM2K-24x petrol atmospheric and turbocharged Kia/Hyundai vehicles.
You can edit the following cards:
Air calculation: correction of measured MAF, maximal airmass flow, target air mass flow f..
Software module for editing calibrations Continental SIM2K-260 and SIM2K-261 ECUs of petrol normal aspirated and turbocharged Kia/Hyundai vehicles.
Available maps:
Air calculation: Air mass flow through the throttle body, Target air mass flow in additional mode
Driver reque..
Module for editing of calibrations turbo diesel Ford c units Delphi DCM6.1.
A list of available maps: the expected mass air flow mass air flow to control the usr specified boost pressure and the limit boost pressure, map control VNT controller to regulate the charge card modes for activation ..
Module for the calibration of the firmware control unit Delphi MT05, MT05.2, MT05.3 used in various types of motorcycles.
You can edit the following cards:
Basic content, the volumetric efficiency correction volumetric efficiency, throttle position to enter the full load rpm of..
FID: 2
Module for working with Delphi MT05 and Delphi MT05.2/3 ECUs through the diagnostic connector or on the bench. It allows identification, read FullFlash with automatic MCU detection and write the calibration area, as well as automatic correction checksums while writing.
&..
Module to work via the diagnostic connector on the CAN bus with the control units Bosch installed on diesel and petrol cars BMW E-series. Does not require the removal, opening or drilling unit!
Allows shared read-write field calibrations.
The module supports:
..
FIDs: 142, 143, 305, 306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316, 349, 353
A module for working with gasoline, electric and diesel cars with Denso SH72xxx CAN control units.
The work is performed when connected to the table via the CAN bus. Removing the ECU is necessa..
FID: 106, 107, 108, 124
Module to read and write via the diagnostic connector diesel vehicles Chrysler/Dodge/Jeep with the control units of Bosch.
FCA Bosch EDC17C49 (FID: 106)
The control unit is a processor Infineon Tricore TC1797 internal flash memory of 4.0 M..
FID: 12, 13, 14, 15, 16, 17
Module to read and write via the diagnostic connector Chrysler/Dodge/Jeep and Fiat control units for Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2.
Allows for tuning most cars of these brands 2004-2014 year of release. The main criterion for the select..
FID: 18, 19, 20, 21 GPEC2 29bit, GPEC2A
Module to work through the diagnostic connector with car production FCA group (Chrysler/Dodge/Jeep/Fiat) with the control units Continental GPEC2 LOCKED, GPEC2 29bit, GPEC2A.
These units are installed on diesel vehicles listed brands and since 2013 ..
FIDs: 326, 327, 331
Module for reading and writing Ford petrol vehicles with Bosch ME(G)9 ECUs.
Ford Bosch ME9.0 (FID:327)
This FID is for working with Bosch ME9.0 ECUs based on Motorola MPC561 with external flash memory 2Mb.
Allows ID, reading/virtual reading and writi..
FID: 180, 181
Module to read and write via the diagnostic connector Ford control units Bosch MG1.
Ford Bosch MG1CS015 TC277 (FID: 180)
The family support units Ford Bosch MG1CS015 processor-based Infineon Aurix TC277 with internal memory of 4 MB.
Allows readi..
FIDs: 255, 256, 257, 259, 260, 261, 262, 263
Module for reading and writing Ford diesel vehicles with Continental SIDxxx ECUs.
Work is possible with OBD2 or on the Bench.
Ford Continental SID206 (FID: 259)
This FID is for working with Continental SID206 ECUs ..
FIDs: 265, 266, 267, 268, 269, 270, 271
Module for reading and writing by CANbus Ford petrol vehicles with Continental EMSxxxx ECUs.
Ford Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BIN
Ford Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BIN
Ford..
FIDs: 301, 302, 318
Module for reading and writing by CANbus Ford diesel vehicles with Delphi ECUs.
Ford Delphi DCM3.5 (FID: 301)
This FID is for working with Delphi DCM3.5 ECUs based on MPC5566 with internal flash memory 3Mb.
Allo..
Module for the calibration of the firmware control unit ACDelco E92 atmospheric petrol cars of GM (Chevrolet, Cadillac, etc.)
You can edit the following cards:
Fan Control: the Desired FAN control, FAN control via Desired coolant temperature
Fuel: AFR target valu..
FID: 91, 94, 96, 97, 98, 99, 100, 102
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen1 installed on petrol cars of GM (Opel, Chevrolet, etc.).
ACDelco GM E38 (FID: 96)
The control unit is based on the processor Motoro..
FIDs: 128, 129, 167, 168, 176
Module to read and write via the diagnostic connector on the CAN bus control unit ACDelco Gen2 installed on petrol cars of GM.
GM ACDelco E39A Gen2 (FID: 129)
The control unit is powered by a processor from NXP MPC5566's internal fla..
FID: 65, 67
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars of GM (Opel, Chevrolet, Saab).
GM Bosch EDC16C39 HW1 (FID: 65)
The control unit is powered by the Motorola MPC562 processor with ext..
FID: 30, 43
Module to read and write via the diagnostic connector of the motorcycle brand Harley-Davidson with control units Delphi.
HD Delphi MT05 CAN (FID:30) on the basis of MC9S12XEP768 NXP MCU with internal flash memory 768Kb.
HD Delphi VooDoo CAN (FID:43) on the basis of NXP MC9..
Module for editing of calibrations turbocharged petrol Honda cars with control units Bosch MED17.9.3.
For edit following maps: calculation of the air mass through the throttle, the calculation of the cyclic filling and optimal torque, maximum torque in normal and sport modes, maps, calculatio..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Continental .
It supports all the Continental blocks with the Motorola processor MPC5554 2Mb.
We provide the following card for editing: Control of valve timing (VTC), closed loop c..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units from Hitachi.
All the blocks are supported Hitachi CPUs with 1Mb Renesas SH7058, SH7059 1.5 Mb, 2Mb SH72543 and Motorola MPC5554 2Mb.
We provide the following card for editing: Cont..
Module for editing of calibrations of Honda/Acura with turbo petrol engines volume of 0.66 l and control units from Hitachi.
Supported cars: Honda S660 (2014+), Honda N-One, Honda N-Box and so on. with the engine S07A Turbo.
Maps available: the expected boost pressure, boost limiter, the ..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units are Keihin.
It supports all blocks Keihin processor SH7058, SH72543, MPC5566.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, the openi..
Module for editing calibrations of Honda cars with 1.5 L atmospheric gasoline engines and Keihin control units based on the TC1782 processor.
Supported file size: 2.5 MB
Supported Maps:
Air Calculation: Air Charge Efficiency High VTEC, Air Charge E..
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 1.5 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
Module for editing of calibrations of Honda cars with turbo petrol engines volume of 2.0 l and the control units are Keihin.
Calculation and Air boost intake system efficiency, boost pressure threshold for operation wastegate, wastegate duty, boost limitation by EGT, load limitation, maxi..
Module for editing of calibrations of Honda/Acura with turbo petrol engines 2.3 l and control the Keihin on the basis of the Renesas SH7058 processor with internal memory of 1Mb.
Maps available: the expected boost pressure, a control valve timing (VTC), closed loop composition of the mixture,..
FIDs: 228, 229
Module for working with Keihin control units installed on Honda Marine outboard motors.
Allows identification of the software version, reading and writing full flash, checking and counting the COP, reading and writing eeprom, recovery from any state.
..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Matsushita.
Supported all blocks Matsushita Renesas processors with 512Kb SH7055, SH7058 1Mb, 2Mb SH72543.
We provide the following card for editing: Control of valve timing (VTC), ..
A module for editing firmware of motorcycles, scooters, ATVs and other Honda motorcycles with Keihin control units.
Due to the rather large variety of Keihin block types and processor types used in them, the set of maps available for editing can be very different for each file. An ..
FIDs: 125, 126, 174, 175, 226, 227
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.
Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.
..
FID: 337
A module for reading and writing Shindengen control units installed on Honda motorcycles.
Honda Moto Shindengen V850/RH850 K-Line (FID:337)
Sihndengen engine control units are powered by Renesas V850/RH 850 series processors with 256/384Kb internal flash memo..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Motorola processors Renesas SH7055 internal memory of 512 KB and Renesas SH7058 1024 KB.
Include a map to edit: Control of valve timing (VTC), closed loop composition of the mixture, th..
Module for editing of calibrations the entire line of Honda cars with atmospheric engines and control units Panasonic processor Infineon Tricore TC197X with internal flash memory 4Mb.
..
FID: 340
Module for working with Honda/Acura cars via CAN bus with Keihin control units.
The family supports control units:
Keihin SH7058 (1MB)
Keihin SH72543 (2MB)
Keihin MPC5554 (2MB)
Keihin TC1782 (2.5MB)
Keihin TC275 (4MB)
Ke..
FIDs: 365, 366, 367, 371
A module for reading and writing flash memory of Delphi engine control units in diesel cars of the Indian market.
Allows identification of the software version, reading, writing with CS correction.
Tata Delphi DCM2.5 XC2XXX CAN (..
FID: 280
Module for reading and writing by CANbus Isuzu diesel vehicles with Transtron ECUs based on Renesas SH7058, SH7059, SH72533 and SH72544.
Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)
Family for Transtron ECUs based on MCUs Renesas SH7058/SH7059/..
Module for firmware calibration of Transtron ECUs with Infineon Aurix processors for Isuzu diesel cars with 3.0TD 4JJ3 engines.
Supported maps:
Boost Pressure: Boost limit per Atmospheric Pressure Correction, Boost limit per intake air temperature, Boost Pre..
Module for calibration of firmware of Delphi control units for diesel Isuzu vehicles.
Supported maps:
Boost Pressure: Target Boost atmospheric pressure correction, Target Boost Base, Target Boost Coolant Temperature, Target Boost Intake Air Temperature Compensation, T..
Module for the calibration of firmware control blocks Kefico CPEGD2/CPGDSH2 petrol atmospheric and turbocharged Kia/Hyundai vehicles.
Available maps:
The filling: Ripple sensor mass air flow, the calculated content
Control boost the Efficiency of the compressor and th..
Attention! A special BITS001 adapter (or an alternative with automatic BOOT pin control) is necessary and required for operation. Guaranteed to work only with the J2534 adapter Skanmatik SM2/SM2 Pro, also works with Bosch VCM2.
Module for reading and writing in the mode of..
Module for reading and writing control units installed on diesel cars Korean brands Kia/Hyundai.
Hyundai Denso Diesel SH72546 (FID: 42)
The control unit is powered by a processor Renesas SH72546 with internal flash memory of 3.75 Mb.
Allows shared read and write ..
FID: 251, 253
Module for reading and writing control unit Kefico CPGDSH2.2x.x/CPEGD2.20.x installed on petrol cars Korean brands Kia and Hyundai.
Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)
These types of units are processo..
Module to read and write via the diagnostic connector on the CAN-bus control units installed on diesel cars Korean brands Kia/Hyundai.
Kefico CPEGD2/CPGDSH2 (FID: 70)
Control units Kefico CPEGD2.20.1 and CPGDSH2.26.1 work based processor Infineon Tricore TC1782 with ..
Module for the calibration control systems for petrol turbocharged engines of cars Dodge, Jeep, Fiat, Abbarth with the control units of Magneti Marelli 8Gx.
Available to edit the map limits power and torque, otnositelnye power query and power maps for different modes, control the XX, phase in..
Module for editing a ECU Magneti Marelli IAW9GV used in the cars of concern VAG c engine CFZA 1.6.
Idle speed in all modes
The friction torque and mechanical loss torque, the requested torque in different modes and on different gears, torque limit, the relative momentum and the mome..
Module for editing a ECU Magneti Marelli IAW7GFR used in FoMoCo vehicles.
We offer to edit the following calibration: control of the twentieth, the limiter engine speed, correction and calculation of the air mass, the throttle control, the composition of the mixture at partial and full loads,..
Module for editing a ECU Magneti Marelli IAW7GV used in the cars of concern VAG for 1.6 engines CFNA, CFNB, CLRA, CLPA, CLSA, CGGB.
To adjust available the following cards:
The injection correction injection for IDENTITY, and control of the injection phase at start-up
Idle speed..
Module for the calibration firmware petrol cars Mazda c control Denso processors Renesas SH7055, SH7058.
You can edit the following cards:
Air load: engine load limitation, load correction for MAF
Configuration: engine volume, dwell time, MAF scaling
EGR: EGR..
Module for the calibration of the firmware control unit Denso diesel Mazda engine SkyActiv-D.
Editable the following cards:
Control boost: limit the boost pressure by the atmospheric pressure, the boost limiters, the desired boost pressure, the correction valve current control of boos..
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
Module to calibrate the firmware of the control units Mitsubishi petrol cars with the Mazda 2.3 Turbo motor.
Available the following cards:
Boost pressure: boost limitation on closed throttle, boost pressure limitation, pressure desired boost, desired load, intake pressure ..
Module to calibrate the firmware of the control units Mitsubishi petrol cars Mazda engine SkyActiv-G 1.3, 1.5, 2.0, 2.5 liters.
Editable the following cards:
The pressure in the rail for direct injection, the estimated temperature of the EXHAUST gas phase of the intake and exhaust shafts,..
FID: 238, 242, 245, 246
Module for reading and writing control unit Denso installed on diesel vehicles with engines Mazda SkyActiv-D.
Mazda Diesel Denso Gen3 SH72543 (FID: 246)
The control unit is powered by a processor Renesas SH72543 with internal flash memory ..
FIDs: 240, 241, 243, 244, 249
Module for reading and writing control unit Denso and Mitsubishi installed on petrol cars with engines Mazda SkyActiv-G.
Mazda Denso Gen3 (D02) (FID: 244)
The control unit is powered by a processor Renesas SH72543 with internal flash..
FID: 200, 201, 202
Module to read and write via the diagnostic connector diesel Mercedes-Benz cars with control units Bosch EDC17.
Supported the following units:
Bosch EDC17CP01 / EDC17CP10 (FID: 200)
Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
Bosch EDC17CP46 (F..
FID: 203, 204, 205, 208
Module for virtual read and write via the diagnostic connector petrol Mercedes-Benz vehicles with the control units Bosch MED17.
Supported block types are:
MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
MB Bosch MED17.7.3.1 (FID: 204)
MB B..
FIDs: 214, 216, 217, 218
Module to read and write via the diagnostic connector diesel cars Mercedes-Benz control units for Delphi CRD.
MB Delphi CRD3.xx (FID: 214)
The family support units Delphi CRD3.xx on the basis of the Infineon Tricore TC1797 CPU ..
Module for reading and writing on the table (without opening) of control units Continental SIM271DE2.0 and Siemens SIM271KE2.0 installed on gasoline vehicles Mercedes-Benz.
Continental SIM271DE2.0 (FID: 209)
FID supports with blocks of Continental SIM271DE2.0 process..
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel vehicles Mitsubishi.
Supported file size is 1Mb.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control: ..
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel vehicles Mitsubishi.
Supported file size - 1.5 MB.
You can edit the following cards:
Air mass: the expected air mass, the expected mass of air with EGR off
Boost control..
FID: 334
A module for reading and writing via the CAN bus of Mitsubishi MH8XXX control units installed on Mitsubishi Motors Corporation (MMC) gasoline cars.
Mitsubishi MH8XXX CAN (FID:334)
The module allows software identification, reading, writing, counting CS with a..
FID: 64, 103
Service module for identification and virtual reading of the firmware control unit Denso 32920-4xxxx. The ECU is powered by a Renesas SH7052 CPU.
Read the actual flash memory of a given block is only possible by drilling a fairly large hole in the hull f..
The module is designed to work through a diagnostic connector with Eldor blocks used on motorcycles of different brands. Allows identification of the software version, virtual reading and writing, as well as automatic correction of checksums during recording.
The control un..
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4 Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the cons..
Module for the calibration control systems for gasoline engines Chrysler/Dodge/Jeep with the control units NGC4A Motorola processor MPC5554 internal flash memory 2Mb.
The following calibration: Volumetric efficiency, its correction and multipliers, calculate the mass flow at start-up, the con..
Module for the calibration of the firmware control unit Denso SH7058 processor for diesel Nissan.
Supported file size is 1 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection in..
Module for the calibration of the firmware control unit Denso processor SH7059 for diesel Nissan.
Supported file size - 1.5 MB.
Available the following cards:
Expected mass air flow, the expected boost pressure, the boost limit, limiting the amount of injection i..
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7054 used for atmospheric petrol Nissan/Infiniti.
Supported size firmware 384Кб.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in ..
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7055 used for atmospheric petrol Nissan cars.
Supported size 512 KB firmware.
Available the following cards: basic and additional card account for the fraction of fresh intake air, the fuel in the..
Module to calibrate the firmware of the control units Hitachi Gen1 on the basis of the Renesas SH7058 processor that is used for atmospheric petrol Nissan cars.
Supported firmware size of 1MB.
Available the following cards: basic and additional card account for the fraction of fresh intak..
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH7059 used for atmospheric petrol Nissan cars.
Supported firmware size 1.5 MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensation o..
Module to calibrate the firmware of the control units Hitachi Gen1 processor-based Renesas SH72xx used for atmospheric petrol Nissan/Infiniti.
Supported size 2.0 firmware MB.
Of available maps: the fuel in the regulatory regime and the underlying composition of the mixture, the compensati..
Module to calibrate the firmware of the control units Hitachi Gen2 diesel turbocharged and naturally aspirated vehicles Nissan. Supported file MCU Renesas SH72533 size 2.0 MB.
Editable the following calibration: sensitivity Control PID-boost regulator correction according to the de..
Module to calibrate the firmware of the control units Hitachi Gen1 petrol turbocharged Nissan (Juke 1.6 T Tiida 1.6 T, GTR).
Supported file MCU Renesas SH7058 size 1.0 MB.
Available the following cards:
The specified boost pressure, multiplier to limit and boost cut-off, the calculati..
FID: 179, 210, 211, 232
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)
This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows readin..
FIDs: 346, 347
A module for working on a CAN bus with control units of Peugeot and Citroen petrol cars.
PSA Valeo V46.11 (FID: 346)
The control unit is powered by a Renesas SH72544 processor with 2.5 Mb internal flash memory. Allows reading and writing of the..
FID: 139, 154, 165, 169, 178
Module to read and write via the diagnostic connector control unit for petrol cars of the Renault brand.
Renault Continental EMS3110 (FID:139)
Family to work with blocks of Continental EMS3110 based processor Infineon Tricore internal..
Module to calibrate the firmware of the control units Siemens EMS3150 for turbocharged petrol Renault / Dacia.
This module provides a set of cards is sufficient to create the modified files at any Stage:
Control boost PWM control valve boost limit the boost and MAF, threshold of time ..
FIDs: 155, 157, 177
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.
Renault Siemens SID301 (FID:157)
This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0..
The module is designed to work with a variety of extreme vehicles on the Rotax motors with the control units Bosch ME17.8.5 and Siemens MSE of 3.7 x. The work is performed via the diagnostic connector or on the table without opening the control unit.
Siemens MSE 3.7 x
The family of Siemen..
Module for the calibration firmware different motorcycles BRP, Aprilia with the control units Siemens MSE 3.7/ 3.71.
Available the following cards:
The revolutions of the twentieth, the thresholds of the exit of the twentieth, the calculation of the injection time, the efficien..
Module for reading and writing control unit Delphi installed on diesel cars of mark SsangYong.
SsangYong Delphi DCM6.2AP (FID: 32)
Work processor-based NXP SPC5673 with an internal memory of 3Mb.
Available read and write field calibration via CAN bus, checksum correction. R..
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)
Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
This ECU is used on SsangYong pe..
FID: 198
Module for working on the BENCH with Mitsubishi ECUs used in Suzuki Marine Outboards.
FID 198: Suzuki Marine Mitsubishi MH8104F K-Line
Allows software identification, FullFlash reading and writing by K-line, CS calculation. Supports:
S..
Module support editing the entire line of diesel engines Toyota 1.4 and 1.6 D-4D with control units Bosch EDC15, EDC16, EDC17.
To edit any one of the following cards: calculation of air mass for the usr, the thresholds to enable the usr specified boost pressure and the boost limiters, control..
FID: 140
Module for virtual read and write via CAN bus control units Toyota Delphi Gen1 installed on gasoline vehicles Toyota/Scion.
Toyota Delphi MPC565/SH72xx (FID: 140)
The module allows to work with three types of units a Delphi running on different processor..
Module for the calibration of control systems of diesel engines of Toyota and Scion control units for Delphi.
Supports all types of blocks Delphi - MPC and SH72xx (1mb, 1.5 mb, 2mb file size).
The efficiency of the intake: the intake efficiency of the intake and vypu..
The module allows you to make configuration of control systems of diesel engine capacity of 2.0 and 2.2 liters of Toyota and Lexus with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost..
The module allows you to make configuration of control systems of diesel engines of 2.5 and 3.0 litres Toyota cars with control units, Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ..
The module allows you to make configuration of control systems of diesel engine capacity of 4.5 liter Toyota with the control module Denso 89661-xxxxx.
You can change the calibration of the fuel rail pressure, cyclic fuel delivery, the request torque, limit torque, boost pressure. For more ac..
The module allows you to make configuration of control systems of diesel engine capacity of 4.0 liter trucks Toyota Hino with the control module Denso 89661-xxxxx (MCU 76F0039AGD, 76F0085).
Available for editing: curves for converting the basic sensors, a given boost pressure, the boost limit..
Module for the calibration of the firmware control unit Denso diesel newGen Toyota vehicles with an engine capacity of 2.4 and 2.8 TD.
The module supports firmware files:
MCU D76F0196F1 1536Kb
MCU D76F0219F1 2048Kb
You can change the calibration of the fuel rail..
Software module for editing calibrations Denso Gen3 ECUs of diesel Toyota vehicles with 2.4TD 2GDFTV and 2.8TD 1GDFTV engines .
Supported filesize: 4Mb.
Available maps:
Air calculation: Air flow correction, Desired air calculation, Desired air calculat..
The module allows you to adjust the transmission of Toyota, Lexus, in which the control program resides in a separate processor NEC 76F0040AGD.
We offer to edit the following settings of the transmission conditions for the transmission shift up and down, control pressure switch, overall oil p..
Module for virtual read and write via CAN bus control units, Denso Toyota Gen1 installed on petrol and diesel cars Toyota/Lexus/Scion/Hino.
Toyota Denso NEC 76F00XX (FID: 24)
The supported control units, Denso's CAN-bus and works on the basis of processors NEC 76F003..
A module for reading/virtual read and write via the diagnostic connector of the control units of the new generation Toyota Denso newGen installed on petrol and diesel cars of Toyota Lexus.
The module consists of two types of protocols:
Type 1
Supported read-write..
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)
Supports Denso ECUs based on MCU Renesas R7F7012..
The module allows you to make configuration of control systems for gasoline engines 1.0, 1.2, 1.3, 1.6, 1.8 litre Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the..
The module allows you to make configuration of control systems for gasoline engines 2.0, 2.4, 2.5 and 2.7 liters Toyota, Lexus, Scion with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following calibration: the ..
The module allows you to make configuration of control systems of diesel engine capacity of 3.0, 3.3 and 3.5 litre Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, mi..
The module allows you to make configuration of control systems for gasoline engines 4.0, 4.3, 4.6, and 4.7 liters of cars Toyota, Lexus with the control module Denso 89661-xxxxx and NEC processors 76F0038, 76F0039, 76F0040, 76F0070, 76F0085.
Currently it supports the following card..
The module allows you to make configuration of control systems of diesel engine 5.0 and 5.7 liter Toyota, Lexus with the control module Denso 89661-xxxxx and processors 76F00XX. Currently it supports the following calibration: the ignition timing for high and low fuel quality, minimum angle, the ..
The module allows you to make configuration of control systems for atmospheric petrol engines Toyota, Lexus new generation control units newGen. Supported files with new MCUs D76F0xxx size and 1536Kb 2048Kb.
Currently it supports the following calibration: the ignition timing for h..
An adjustment module for petrol atmospheric engines of cars Toyota, Lexus with old control units, Denso processors 76F0015 and 76F0021. The size of the firmware 320 and 384 KB.
Attention! To date, these processors are not subject to reading and writing in BSL mode. Entry is only po..
Module for the calibration of the firmware control unit Denso diesel turbocharged Toyota and Lexus, the new processors NEC D76F0xxxF1. The size of the firmware is 1536 KB.
Supported models:
Lexus NX 200t
Lexus IS 200t
Lexus GS 200t
Lexus RX 200t
Toyo..
Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A ..
Service module for the virtual reader firmware blocks GEN1 Denso on Toyota, Lexus, Scion, Hino.
Allows to identify FOR the car and if there is a corresponding file on the server to download it.
Attention! The module does not provide RECORDING.
Files for blocks Denso Gen2/newGen 1.25, ..
Module for the calibration of the firmware control unit Denso c processor Renesas SH72531 used on gasoline-powered cars, Toyota GT86, Subaru BRZ, Scion FR-S.
Available maps:
The limitation of the load, calibration of a flowmeter of air, the temperature of the fan switch, the ex..
FID: 117, 118
Module for reading and writing to the CAN bus control unit Delphi DMCI, mounted on DAF trucks and Hyundai.
The control unit is based on the processor Motorola MPC561 external flash memory 2.0 Mb.
Allows read and write field calibration via CAN-bus w..
Module to read and write via the diagnostic connector on the CAN bus the control units of the Delphi ETC3, installed on trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.
DAF/Industrial Delphi ETC3 (FID: 220)
The family support units of the Delphi ETC3 processor-based ..
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module to read and write via the diagnostic connector on the CAN bus the control units Bosch EDC17CV41, installed on trucks and buses, Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.
The control unit is a processor In..
FID: 401, 402
Module for working with Continental Simos 12 and Simos 18 ECUs used in VAG vehicles.
VAG Continental Simos 12.X (FID: 401)
Supports Simos 12.1 and 12.2 ECU types.
ECU based on TC1797 with internal flash memory 4Mb.
Allows reading and..
The module for blocks management Magneti Marelli installed on petrol cars of concern VAG (Audi/Seat/Skoda/VW).
Magneti Marelli IAW 7GV (FID: 5)
This block is used for cars of concern VAG engines 1.4/1.6 CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB. Supported read full fl..
VAZ M86 (FID: 348)
Module for reading and writing ECUs by CANbus used in Lada/VAZ petrol vehicles.
ECU is based on MCU Infineon XC27XX with internal flash memory 1088Kb. Allows virtual reading and writing of calibration area by OBD2 with checksum correction on writing.
..
Single-Board multi-brand scanner DS150e Bluetooth is a quick and reliable diagnostic tool serving as a link between vehicle and computer. It works on both old and new cars. Simply plug a single Board DS-150 to the diagnostic connector of the car, and he will contact you with the diagnostic progra..
