MasterEditPro Modules

Includes maps of the major calibration firmware M7.8.0. Free map updates for new software Bosch M7.8.0. Works with standard format firmware. Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, o..

In stock

Bosch M7.8.0 module 1

Includes all the module 1, the calibrated dual-mode firmware Bosch M7.8.0 and map-editing dual-mode firmware. Possible dual firmware Bosch M7.8.0: switching between the main calibrations (more than 20). Organization of switching modes according to the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, on-hold pedal to switch, etc.). ..

In stock

Bosch M7.8.0 module 2

Включает карты основных калибровок прошивок M7.8.0. Бесплатное обновление карт для новых софтов Bosch M7.8.0. Работает с стандартным форматом прошивок. Возможности двухрежимных прошивок Bosch M7.8.0: Переключение основных калибровок (более 20). Организация переключения режимов по сигналам ДТВ, ДК2 или педали газа. Типы переключение режимов тумблер/кнопка. Тонкая настройка срабатывания переключения (АЦП фиксации в момент..

In stock

Bosch M7.8.0 модуль 1

$56.96

In stock

EMS3120 module 1

Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera, Duster (engines D4F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries 'reprove', calibration off ДК2 and control system thresholds, inclusion of L-regulation, start-up calibra..

Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for fixing the general KSPZ At and each area separately. Works with the standard firmware format. ..

In stock

EMS3120 module 1

EMS3120 module 1 in the presence of two or more of any module MEPro

In stock

Designed for Renault cars/VAZ/Nissan Logan2, Sandero2, Lada Largus, Nissan Almera (motors D7F, K7M, K4M) MT and AT ECUS are equipped with Continental EMS3120. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries 'reprove', calibration off ДК2 and control system thresholds, inclusion of L-regulation, start-up calibration, cal..

$56.96

In stock

EMS3125 module 1

Designed for vehicles Renault/VAZ Logan2, Sandero2, Kaptur, Lada XRAY (H4M engines, F4R) MT and AT ECUS are equipped with Continental EMS3125. The module contains a set of basic calibrations, including: the Extended mask error, detailed identification information, the ability to view log entries 'reprove', calibration off ДК2 and control system thresholds, inclusion of L-regulation, start-up calibration, calibration constra..

GAZ M74.9(1) Read/Write/Configuration Script

In stock

For ITELMA GAZ M74.9/M74.9.1 ECUs (259.3765 004-01/11). Supports identification, fault codes, Flash and EEPROM read/write, VIN editing and checksum checks. Connect via OBDII or directly; J2534 required. A J2534 adapter is required...

GAZ M74.9/M74.9.1 Module 1

In stock

Calibration maps for GAZ M74.9 and M74.9.1 (259.3765 004-01/11) ECUs with ITELMA software. Supports checksum recalculation, checksum locking and the standard firmware format...

GAZ M74.9/M74.9.1 Recorder

In stock

Edits recorder data in GAZ M74.9 and M74.9.1 ECUs with ITELMA software. Checks data integrity and recalculates required checksums. Works with EEPROM or a full firmware dump containing recorder data...

GrantaFL (from 2025) Immobilizer and Central Body ECU Read/Write/Service/Configuration Script

In stock

For ITELMA immobilizer and central body electronics units in LADA GrantaFL from 2025. Supports key learning/clearing, pairing with the M74.9(1) engine ECU, software updates and configuration. J2534 required. A J2534 adapter is required...

GrantaFL/NivaL MC9S12HY64 Instrument Cluster Read/Write/Configuration Script

In stock

For ITELMA instrument clusters in GrantaFL and NivaLegend with MC9S12HY64 (from 2018). Supports EEPROM reading, firmware read/write without BOOT, diagnostics, configuration and odometer editing. J2534 required. A J2534 adapter is required...

GrantaFL/NivaLT Artery Instrument Cluster Read/Write/Configuration Script

In stock

For ITELMA instrument clusters in GrantaFL, NivaLegend and NivaTravel with Artery MCU (from 2023). Supports FullFlash reading, firmware writing, diagnostics, configuration, odometer and operating-time editing. J2534 required. A J2534 adapter is required...

GrantaFL/NivaLT Kesens/ITELMA ABS Firmware/Configuration Script

In stock

For Kesens/ITELMA ABS in GrantaFL, NivaLegend and NivaTravel; supports NXP FS32K144, Flagchip and TriCore TC234. Supports diagnostics, software update/recovery, configuration and odometer editing. J2534 required. A J2534 adapter is required...

ISKRA/VestaNG Artery Instrument Cluster Read/Write/Configuration Script

In stock

For LADA ISKRA instrument clusters with Artery; the developer lists VestaNG support for 2026 models. Supports FullFlash reading, firmware writing, diagnostics, configuration and odometer editing. J2534 required. A J2534 adapter is required...

ITELMA Additional Body Electronics Firmware/Configuration Script

In stock

For the ITELMA additional body electronics unit in LADA XRAY, Vesta and VestaNG (STM8/STM32). Supports identification, fault codes, firmware writing, configuration reading and editing. J2534 required. A J2534 adapter is required...

ITELMA CAN Gateway Diagnostics/Configuration Script

In stock

For the ITELMA CAN gateway in LADA VestaNG and ISKRA from 2025. Supports identification, diagnostics, VIN/configuration changes and configuration-lock removal. J2534 required. A J2534 adapter is required...

$43.81

In stock

ITELMA Electric Power Steering Firmware/Diagnostics/Configuration Script

For ITELMA electric power steering in LADA vehicles from 2023. Supports diagnostics, VIN/configuration, steering-zero calibration, software updates and recovery. J2534 required. A J2534 adapter is required...

$43.81

In stock

ITELMA VestaNG Access and Start Unit Read/Write/Service/Configuration Script

For the ITELMA access and start unit in keyless VestaNG vehicles with key cards. Supports software updates, key EEPROM operations, key-card learning/clearing, configuration and pairing of the access unit, uBCM and engine ECU. J2534 required. A J2534 adapter is required...

January 7.2+ module 2 (only for users of the Module M73)

In stock

Available only when the module M73. Includes all the module 1, the calibrated dual-mode firmware Jan 7.2+ and map-editing dual-mode firmware. ..

KIA/Hyundai Bosch M(G)7.9.8 module 1

In stock

Includes maps calibrations for all (known) firmware KIA/Hyundai Bosch M(G)7.9.8. Free map updates for new software Bosch M(G)7.9.8. Works with standard format firmware. Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, l..

KIA/Hyundai Bosch M(G)7.9.8 module 2

In stock

Includes all the module 1, the calibrated dual-mode firmware KIA/Hyundai Bosch M(G)7.9.8 (more than 260 modified to switch firmware) and maps editing dual-mode firmware. Possible dual firmware KIA/Hyundai Bosch M(G)7.9.8: Switching basic calibrations (more than 50). Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, ..

KIA/Hyundai Bosch ME(D)17.9.8 module 1

In stock

Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. Or via OBD (diagnostic method), provided that the boot loader supports it. ..

KIA/Hyundai Bosch ME(D)17.9.8 module 1 to module owners ME17.9.21

In stock

Includes maps of the calibration firmware the atmospheric GDI and Turbo GDI engines (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. Or via OBD (diagnostic method), provided that the boot loader supports it. ..

KIA/Hyundai Bosch ME(D)17.9.8 Module 2

In stock

Includes Module 1 and dual-mode firmware creation by combining two single-mode files. All ECU calibrations are switched; mode switching uses the rear oxygen sensor signal. Price for ME17.9.21 owners: RUB 6,000; upgrade from Module 1: RUB 2,000...

$146.05

In stock

KIA/Hyundai Bosch ME17.9.11(12,13) module 1

Includes maps calibrations for all versions (free map updates for new software). Works with standard (uncompressed) format. Writing a modified firmware available only via BSL mode any existing boot loader. ..

$102.23

In stock

KIA/Hyundai Bosch ME17.9.11(12,13) Module 2

Includes Module 1 and dual-mode firmware creation. Supports copying calibrations between modes and firmware files, and disabling the fuel-pump relay in either mode. Switching is triggered by the rear oxygen sensor signal...

KIA/Hyundai Bosch ME17.9.21 module 1

In stock

Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. Or via OBD (diagnostic method), provided that the boot loader supports it. ..

KIA/Hyundai Bosch ME17.9.21 module 1 to module owners ME(D)17.9.8

In stock

Includes maps of the calibration firmware the atmospheric MPI engines up to 1.6, inclusive, (free map updates). Works with standard (uncompressed) format. When you save the firmware recalculates the checksum of the calibration and code, it allows you to record them via BSL mode any existing boot loader. Or via OBD (diagnostic method), provided that the boot loader supports it. ..

KIA/Hyundai Bosch ME17.9.21 Module 2

In stock

Includes Module 1 and dual-mode firmware creation by combining two single-mode files. All calibrations are switched and the fuel-pump relay can be disabled. Price for ME(D)17.9.8 owners: RUB 6,000; upgrade from Module 1: RUB 2,000...

$146.05

In stock

LADA EnjoY Multimedia Diagnostics/Configuration Script

For the LADA EnjoY (PRO) multimedia system. Supports identification, diagnostics and configuration. Connects via OBDII; CAN pin switching may be required depending on the adapter. Scanmatik 2 PRO/3 is recommended. A J2534 adapter is required...

LADA ERA-GLONASS Diagnostics/Configuration Script

In stock

For LADA ERA-GLONASS units connected to the vehicle CAN bus. Supports identification, diagnostics, factory-state reset, vehicle-type/VIN changes and configuration. J2534 required. A J2534 adapter is required...

LargusSE Trinova ABS Configuration Script

In stock

For Trinova ABS in LADA LargusSE with Infineon XC2365B MCU. Supports diagnostics, software updates, configuration and odometer setting. J2534 required. Temporary price: RUB 4,000 with the LargusSE/Vesta cluster script (MC9S12HY64). A J2534 adapter is required...

LargusSE/Vesta MC9S12HY64 Instrument Cluster Read/Write/Configuration Script

In stock

For LargusSE (from 2024) and Vesta (through 2022) instrument clusters with MC9S12HY64. Supports EEPROM and firmware read/write without BOOT, configuration, odometer editing and service-counter reset. J2534 required. A J2534 adapter is required...

Includes maps calibrations for all firmware M73. Works with standard format firmware. ..

In stock

M73 module 1

Includes all the module 1, the calibrated dual-mode under LPG firmware M73 (all the existing software) and maps editing dual-mode firmware. So, buyers free program DoubleM73 tied to the key. ..

In stock

M73 module 2

$65.72

In stock

M74 6.38 (M74.5) Module 1

Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of calibrations (over 1500) and partial (to optimize the process in small settings), including the configuration, mask errors, fine-tun..

M74 6.38 (M74.5) Module 2

In stock

Includes all the module 1, the calibrated dual-mode firmware 6.38 M74 and map editing dual-mode firmware. ..

M74 6.38 module 1 for owners module M75

In stock

For owners module M75 Includes maps calibrations for firmware blocks VAZ M74 6.38 (21127). Free map update module M74 6.38. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of calibrations (over 1500) and partial (to optimize the process in small settings), including the configurat..

$51.12

In stock

M74 module 1

Includes maps calibrations for all firmware M74, М74CAN and М74к. Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the ADC, the ADC is fixing the shift points, on-hold pedal to switch, etc.). In any mode, you can optionally disable the fuel pump, i..

Includes all the module 1, the calibrated dual-mode firmware M74 (front wheel drive) and maps editing dual-mode firmware. Possible dual firmware M74: Complete switching of all calibrations in the firmware. Switching on the signals of DTV, ДК2 or the gas pedal. Types switch toggle switch/button. Fine-tune triggering of a switch (limit switch of the ADC, the ADC is fixing the shift points, on-hold pedal to switch, etc.). ..

In stock

M74 module 2

Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of calibrations (over 1500) and partial (to optimize the process in small settings), incl..

In stock

M75 module 1

M75 module 1 to module owners M74 6.38

In stock

For owners module M74 6.38 Includes maps calibrations for firmware blocks VAZ M75 (ELCAR ECU M75). Free map update module M75. For transfer and cleaning of the area of study. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 832kb (or 768kb). To edit an expanded set of calibrations (over 1500) and partial (to optimize the p..

$51.12

In stock

M75 module 2

Includes all the module 1, the calibrated dual-mode firmware M75 and map editing dual-mode firmware. Possible firmware M75 dual mode: switching between the main calibrations (more than 50). The mode switching signal ДК2. In any mode, you can optionally disable the fuel pump, injector, and to set the delay of the transition to any mode. Firmware designed for the professional construction of systems with LPG and commercial mu..

M86/M74M (ACCORDING TO VAZ) module 2

In stock

Includes calibration cards for the firmware of the M86 ECU with VAZ software and the M74M ECU. As well as basic, non-calibrated dual-mode M86 (VAZ) and M74M firmware, dual-mode firmware editing cards. The maps also contain additional calibrations of the "Extended Mix composition" for specialized software M86/M74M. ..

$102.23

In stock

Mikas-11 module 1 (only for users of the Module M73)

Available only when the module M73 Includes maps of the calibration firmware the GAS Mikas 11/11CR/11ET. Works with standard format firmware. ..

The module is intended for editing data from Ieprom blocks Bosch ABS9, VAZ cars (XRAY / VESTA). You can change the main mileage, mileage after ECU reset, TPMS log mileage, VIN, Hardware ID, wheel diameter, TPMS activation flag. The module monitors the integrity of the data upon opening and recalculates all the necessary CAs when saving. It allows you to set the desired mileage, and not reset it. ..

In stock

Registrar VAZ Bosch ABS9

Registrar VAZ M74.8/M74.9 (Itelma software)

In stock

The module is designed to edit the data of the registrar of the VAZ 74.8 and M74.9 blocks with NPO Itelma. The module monitors the integrity of the data when opening and recalculates all the necessary CS when saving. An EEPROM (4 kilobytes) is used for editing. ..

Renault/VestaNG ClimBoxGen3 Climate Diagnostics/Configuration Script

In stock

For Calsonic Kansei ClimBoxGen3 climate systems in Renault and VestaNG vehicles. Supports identification, live data, fault-code read/clear and configuration. J2534 required. A J2534 adapter is required...

The Registrar FOR * itelma UAZ M86I/Микас12

In stock

The module is intended for editing of data logger units UAZ M86I and Микас12 (GAS) with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training data inside the ..

The Registrar M74/М86 (FOR vases)

In stock

The module is intended for editing of data logger units M74 (storing training data in flash CPU) and М86, ON 'VAZ'. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training data inside. ..

The Registrar UAZ Bosch M(E)17.9.7/M(E)17.9.71

In stock

The module is intended for editing of data logger units UAZ Bosch M(E)17.9.7 and M(E)17.9.71. So the module allows to change the counter programmed the ECU. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes, respectively the type of ECU). ..

The Registrar VAZ Bosch ME17.9.7/ME17.9.71

In stock

The module is intended for editing of data logger units VAZ Bosch ME17.9.7 and ME17.9.71. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing is used EEPROM (32 or 64 kilobytes, respectively the type of ECU). ..

The Registrar VAZ M74.5/M75/M86I (FOR * Itelma)

In stock

The module is intended for editing of data logger units M74.5 (6.38), M75 and vases M86I with * Itelma. The ECM monitors data integrity when opening and recalculates all necessary COP when saving. For editing you can use as EEPROM separately (64 kilobytes) and the firmware entirely from the training data inside. ..

UAZ М86І (FOR * Itelma) module 1

In stock

Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb. ..

UAZ М86І (FOR * Itelma) module 2

In stock

Includes all the module 1, the base, not calibrated dual-mode firmware UAZ M86I and map editing dual-mode firmware. Includes maps of the calibration firmware the UAZ with the ECU М86І AT * Itelma. Free map update module UAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb. Possible dual firmware VAZ and UA..

VAZ Bosch M7.9.7+ module 1

In stock

Includes maps calibrations for all firmware VAZ Bosch M7.9.7+. Works with standard and 'compressed' format firmware. Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, on-hold pedal to switch, etc.). In any mode, you can optionally disa..

VAZ Bosch M7.9.7+ module 2

In stock

Includes all the module 1, the calibrated dual-mode firmware VAZ Bosch M7.9.7+cards and editing dual-mode firmware. Possible dual firmware 797+: switching between the main calibrations (more than 30). Switching to DTV signals, the PSD or the gas pedal. Types switch toggle switch/button. Fine tuning of the actuation switch (ADC fixing the shift points, on-hold pedal to switch, etc.). In any mode, you can optionally disab..

VAZ ITELMA uBCM Read/Write/Service Script

In stock

For ITELMA uBCM in VAZ VestaNG, LargusSE and ISKRA. Supports Flash/EEPROM read/write, key, VIN and configuration operations, key learning, lock removal and service functions. J2534 required. A J2534 adapter is required...

VAZ M74.8 (Ithelma software) module 1

In stock

Includes calibration cards of VAZ firmware with ECU 74.9 manufactured by Itelma. Free map updates for this module. Recalculation of all CS in the firmware (BOOT area, main code and calibrations). Calibrations are available for the factory fixation of the CS and an extended software function for fixing the general KSPZ At and each area separately. Works with the standard firmware format. ..

VAZ M74.8(+)/M74.9(1) Read/Write Script

In stock

For ITELMA VAZ M74.9/M74.91/M74.8/M74.8+ ECUs. Supports identification, fault codes, memory and EEPROM read/write, VIN editing and checksum checks. For M74.8/8+, EEPROM read/write and firmware/calibration writing are supported. J2534 adapter required. A J2534 adapter is required...

VAZ WLY CVT Read/Write/Configuration Script

In stock

For WanLiYang CVT units in LADA VestaNG, ISKRA and AZIMUT. Supports identification, fault codes and adaptations, VIN/serial number/counter editing, virtual firmware reading and firmware writing with integrity checks. J2534 required; virtual reading requires Internet access. A J2534 adapter is required...

VAZ М86І (FOR * Itelma) module 1

In stock

Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb. ..

VAZ М86І (FOR * Itelma) module 2

In stock

Includes all the module 1, the base, not calibrated dual-mode firmware VAZ M86I and map editing dual-mode firmware. Includes maps of the calibration firmware vases with ECU М86І AT * Itelma. This engines a 1.8 L 16v with VVT. Free map update module VAZ М86І. Recalculation of the COP calibration of factory fixing, the COP extended its software-lock function of the COP. Works with standard format firmware 1088kb. Poss..

VAZ/GAZ M74.9(1) Dual-Mode Firmware Creation

In stock

An add-on for creating and editing dual-mode VAZ/GAZ M74.9(1) firmware. The corresponding VAZ or GAZ Module 1 is required. Modes switch by rear oxygen sensor signal or accelerator pedal; calibration switching and fuel-pump relay disabling are supported...

VAZ/Renault Bosch 9.x ABS Read/Write/Configuration Script

In stock

For Bosch 9.x ABS in VAZ and Renault/Nissan vehicles. Supports identification, fault codes, EEPROM/firmware read/write and ABS/ESP configuration. RideSelect EDL is included by the developer; the ABS recorder is sold separately. J2534 required. A J2534 adapter is required...

VAZ/Renault Siemens EMS3132 Module 1

In stock

Calibration maps for Siemens EMS3132 ECUs in Lada Largus and Renault Logan/Sandero; the developer plans to add maps for related systems. Supports 256 kB FullBIN and calibration-only files. Code and calibration checksums are recalculated after editing...

VAZ/Renault Siemens EMS3132 module 1

In stock

Includes maps of the calibration firmware the Lada Largus and Renault Logan/Sandera (also the cards will be added calibrations from similar control systems, such as Kangoo, Symbol and others). Free map updates for new software EMS3132. Works with FullBIN 256 kb and the file of some calibrations (note that the calibration file is smaller than 32 kilobytes is not part of the axis of quantization, and some calibration). Module..

VAZ/UAZ Bosch ME17.9.7 module 2 for owners of version ME17.9.7 module 1

In stock

Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7 and maps edit the 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any existing bootloader (recommended to use MultiFlasher). Opportuniti..

VAZ/UAZ Bosch ME17.9.7(1) module 1

In stock

Includes maps calibrations for all versions (free map updates for new software). Works with regular (not compressed) format. This module INCLUDES the CONVERSION of a DIGITAL SIGNATURE! The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any existing bootloader (recommended to use MultiFlasher). ..

$94.93

In stock

VAZ/UAZ Bosch ME17.9.7(1) module 2

Includes all the module 1, basic, not calibrated 3 performance firmware VAZ/UAZ ME17.9.7(1) with possibility of setting the desired composition of the mixture in any mode and map editor 2nd and 3rd mode in this firmware. Works with regular (not compressed) format. The edited firmware can be written as a diagnostic method (without disassembling the unit) or via BSL mode any existing boot loader. Opportunities 3 secure fi..

$153.35

In stock

VAZ/UAZ Takata/Joyson CAN SRS Reset/Diagnostics/Configuration Script

For Takata/Joyson CAN airbag units in VAZ and UAZ vehicles. Supports identification, diagnostics, data reset, VIN, configuration and EEPROM read/write. J2534 required. A J2534 adapter is required...

VAZ/UAZ XC27xx Engine ECU Read/Write Script

In stock

For VAZ/UAZ engine ECUs based on XC27xx/XC2060: M74, M74CAN, M74M, M74.5, M75, M86, M86I and M12. Supports identification, fault codes, BSL/BENCH, supported OBDII writing, Flash/EEPROM read/write, automatic structure detection and checksum checks. J2534 required. A J2534 adapter is required...

VestaNG NXP Instrument Cluster Read/Write/Configuration Script

In stock

For graphical and analogue VestaNG instrument clusters with NXP FS32K14x. Supports EEPROM/firmware read, diagnostics, configuration, odometer and operating time, vehicle emulation and service-counter reset. J2534 required. A J2534 adapter is required...

VestaNG WORLDTECH ESCL Pairing/Service Script

In stock

For the WORLDTECH electronic steering-column lock (ESCL) in VestaNG. Supports identification, diagnostics, software updates, VIN, pairing with uBCM, lock/unlock and service functions. The developer temporarily includes the parking-sensor script. J2534 required. A J2534 adapter is required...

$43.81

In stock

VestaNG/ISKRA Kesens/ITELMA ABS Firmware/Configuration Script

For Kesens/ITELMA ABS in VestaNG and ISKRA (NXP FS32K144/TriCore TC234). Supports software updates/writing, recovery after failed programming, configuration, ESP and sensor functions. J2534 required. A J2534 adapter is required...

ITELMA VestaNG/ISKRA/LargusSE Parking Sensor Configuration Script

In stock

For ITELMA parking sensor and blind-spot units in VestaNG, ISKRA and LargusSE. Supports identification, fault-code read/clear and configuration changes. Temporarily supplied with the ESCL script according to the developer. J2534 required. A J2534 adapter is required...

Basic calibration maps for Январь 7.2 firmware and selected non-commercial versions. Included free with any MasterEditPro module...

Expected arrival

January 7.2 Module 1

Calibration maps for Январь 7.2+ firmware. Supports the standard 576 kB firmware format. Included free with any MasterEditPro module...

Expected arrival

January 7.2+ Module 1

RideSelect EDL Firmware/Configuration Script

Expected arrival

For the Ride Select mode selector in VestaNG and XRAY with Bosch 9.x ABS. Supports diagnostics, firmware writing and configuration. Supplied with the Bosch 9.x ABS script; no separate price is listed by the developer. J2534 required. A J2534 adapter is required...